Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065385 SEAT _0328606 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2658  Short in Sensor with Motor Power Supply Circuit  


DESCRIPTION

This DTC is stored when a power seat motor operates (a position control sensor is being supplied with power) and the power supply voltage does not rise to the specified value.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2658 Short in Sensor with Motor Power Supply Circuit Slide motor position sensor power supply voltage is low
·

Position control ECU assembly (driver seat)

·

Slide motor (Upper seat track rail sub-assembly (driver seat))

·

Power Seat Tilt Motor Assembly (Driver Seat)

·

Power Seat Lifter Motor Assembly (Driver Seat)

·

Reclining Motor (Front Seatback Frame Sub-assembly (Driver Seat))

·

Wire harness or connector



WIRING DIAGRAM

B480108E16
0.99,1.063 1.563,1.344 0.573,0.281 10 false a5 0.969,1.229 3.979,1.635 3.01,0.406 10 false Slide Motor (Upper Seat Track Rail Sub-assembly (Driver Seat)) 2.927,0.552 3.5,0.833 0.573,0.281 10 false 2 1.948,0.563 2.521,0.844 0.573,0.281 10 false 3 1.115,2.208 1.906,2.51 0.792,0.302 10 false a6 1.115,2.365 4,2.75 2.885,0.385 10 false Power Seat Tilt Motor Assembly (Driver Seat) 1.042,3.385 1.615,3.667 0.573,0.281 10 false a7 1.042,3.542 4.25,3.875 3.208,0.333 10 false Power Seat Lifter Motor Assembly (Driver Seat) 1.177,4 4.156,4.385 2.979,0.385 10 false Front Seat Adjuster Assembly (Driver Seat) 0.969,5.99 4.094,6.438 3.125,0.448 10 false Front Seatback Frame Sub-assembly (Driver Seat) 2.031,5.448 2.604,5.729 0.573,0.281 10 false o1 2.031,5.615 3.385,5.885 1.354,0.271 10 false Reclining Motor 5.229,6.573 5.802,6.854 0.573,0.281 10 false SENG 5.24,5.042 5.813,5.323 0.573,0.281 10 false SSRR 5.25,3.021 5.823,3.302 0.573,0.281 10 false SSRL 5.24,1.844 5.813,2.125 0.573,0.281 10 false SSFV 5.24,0.667 5.813,0.948 0.573,0.281 10 false SSRS 4.906,0.552 5.479,0.833 0.573,0.281 10 false 26 4.927,1.729 5.5,2.01 0.573,0.281 10 false 10 4.938,2.875 5.51,3.156 0.573,0.281 10 false 25 4.927,4.927 5.5,5.208 0.573,0.281 10 false 11 4.938,6.469 5.51,6.75 0.573,0.281 10 false 12 4.875,6.896 5.448,7.177 0.573,0.281 10 false a12 4.885,7.063 6.865,7.479 1.979,0.417 10 false Position Control ECU Assembly (Driver Seat) 1.958,1.74 2.531,2.021 0.573,0.281 10 false 3 1.969,2.896 2.542,3.177 0.573,0.281 10 false 3 1.958,4.948 2.531,5.229 0.573,0.281 10 false 3 2.917,1.729 3.49,2.01 0.573,0.281 10 false 2 2.927,2.906 3.5,3.188 0.573,0.281 10 false 2 2.958,4.927 3.531,5.208 0.573,0.281 10 false 2

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2658 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))
3.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - SLIDE MOTOR (FRONT SEAT ADJUSTER ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the a12 position control ECU assembly (driver seat) connector.


b.

Disconnect the a5 slide motor (front seat adjuster assembly (driver seat)) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a12-26 (SSRS) - a5-2 Always Below 1 Ω
a12-26 (SSRS) or a5-2 - Body ground Always 10 kΩ or higher
a12-12 (SENG) - a5-3 Always Below 1 Ω
a12-12 (SENG) or a5-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (SLIDE MOTOR CIRCUIT)
a.

Reconnect the a5 slide motor (front seat adjuster assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a5-2 - a5-3 Slide switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

5.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the a12 position control ECU assembly (driver seat) connector.


b.

Disconnect the a6 power seat tilt motor assembly (driver seat) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a12-10 (SSFV) - a6-2 Always Below 1 Ω
a12-10 (SSFV) or a6-2 - Body ground Always 10 kΩ or higher
a12-12 (SENG) - a6-3 Always Below 1 Ω
a12-12 (SENG) or a6-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (TILT MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (TILT MOTOR CIRCUIT)
a.

Reconnect the a6 power seat tilt motor assembly (driver seat) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a6-2 - a6-3 Front vertical switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

7.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the a12 position control ECU assembly (driver seat) connector.


b.

Disconnect the a7 power seat lifter motor assembly (driver seat) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a12-25 (SSRL) - a7-2 Always Below 1 Ω
a12-25 (SSRL) or a7-2 - Body ground Always 10 kΩ or higher
a12-12 (SENG) - a7-3 Always Below 1 Ω
a12-12 (SENG) or a7-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)
a.

Reconnect the a7 power seat lifter motor assembly (driver seat) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a7-2 - a7-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)))

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

9.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)))
a.

Disconnect the a12 position control ECU assembly (driver seat) connector.


b.

Disconnect the o1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a12-11 (SSRR) - o1-2 Always Below 1 Ω
a12-11 (SSRR) or o1-2 - Body ground Always 10 kΩ or higher
a12-12 (SENG) - o1-3 Always Below 1 Ω
a12-12 (SENG) or o1-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (RECLINING MOTOR CIRCUIT)
a.

Reconnect the o1 reclining motor (front seatback frame sub-assembly (driver seat)) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
o1-2 - o1-3 Reclining switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

11.REPLACE POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

11.REPLACE POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT)
a.

Replace the power seat tilt motor assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR DTC
12.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER SEAT TILT MOTOR ASSEMBLY (DRIVER SEAT) WAS DEFECTIVE)

NG

13.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
13.REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.

Replace the power seat lifter motor assembly (driver seat) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK FOR DTC
14.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT) WAS DEFECTIVE)

NG

15.REPLACE SLIDE MOTOR (UPPER SEAT TRACK RAIL SUB-ASSEMBLY (DRIVER SEAT))
15.REPLACE SLIDE MOTOR (UPPER SEAT TRACK RAIL SUB-ASSEMBLY (DRIVER SEAT))
a.

Replace the slide motor (upper seat track rail sub-assembly (driver seat)) with a new or known good one.

Click hereVehicle Interior>SEAT>POWER SEAT TRACK RAIL ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

16.CHECK FOR DTC
16.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (SLIDE MOTOR (UPPER SEAT TRACK RAIL SUB-ASSEMBLY (DRIVER SEAT)) WAS DEFECTIVE)

NG

17.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))
17.REPLACE RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT))
a.

Replace the reclining motor (front seatback frame sub-assembly (driver seat)) with a new or known good one.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CHECK FOR DTC
18.CHECK FOR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

b.

Recheck for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2685 is not output.



Result:
Proceed to
OK
NG



OK

END (RECLINING MOTOR (FRONT SEATBACK FRAME SUB-ASSEMBLY (DRIVER SEAT)) WAS DEFECTIVE)

NG

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)