When the engine switch is on and the refreshing seat switch is operated, the air conditioning amplifier assembly receives refreshing seat switch position signals and then sends airflow amount signals to each seat cushion climate control blower assembly.
Inspect the fuses for circuits related to this system before performing the following procedure.
The climate control seat system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the climate control seat system after confirming that the communication system is functioning properly.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Clear DTCs.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B14B5 is not output | A |
| DTC B14B5 output | B |
A
B
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| Climate control seat does not operate (for LH) | A |
| Climate control seat does not operate (for RH) | B |
| Both climate control seats do not operate | C |
A
B
C
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| Only seatback climate control blower LH does not operate | A |
| Only seat cushion climate control blower assembly LH does not operate | B |
| Both seat blowers do not operate | C |
A
B
C
Disconnect the c3 seatback climate control blower LH connector.
Disconnect the b8 seat cushion climate control blower assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| c3-1 (IG) - b8-5 (CTB) | Always | Below 1 Ω |
| c3-1 (IG) or b8-5 (CTB) - Body ground | Always | 10 kΩ or higher |
| c3-3 (BFB+) - b8-6 (BBS) | Always | Below 1 Ω |
| c3-3 (BFB+) or b8-6 (BBS) - Body ground | Always | 10 kΩ or higher |
| c3-4 (GND) - b8-4 (BFB-) | Always | Below 1 Ω |
| c3-4 (GND) or b8-4 (BFB-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the seatback climate control blower LH with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly LH) |
Disconnect the b8 seat cushion climate control blower assembly LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b8-1 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| b8-1 (IG) - Body ground | Engine switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b8-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K54 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| b8-7 (SIGN) - K54-24 (LOUT) | Always | Below 1 Ω |
| b8-7 (SIGN) or K54-24 (LOUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the K54 air conditioning amplifier assembly connector.
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Reconnect the b8 seat cushion climate control blower assembly LH connector.
Using an oscilloscope, check the input signal waveform.
| Item | Content |
|---|---|
| Tester Connection | K54-24 (LOUT) - Body ground |
| Tool Setting | 1 V/DIV., 0.5 ms/DIV. |
| Vehicle Condition | ·
Engine switch on (IG) ·
Refreshing seat switch on (blower position) |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the refreshing seat switch with a new or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Front Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
| Result | Proceed to |
|---|---|
| Only seatback climate control blower RH does not operate | A |
| Only seat cushion climate control blower assembly RH does not operate | B |
| Both seat blowers do not operate | C |
A
B
C
Disconnect the o3 seatback climate control blower RH connector.
Disconnect the a9 seat cushion climate control blower assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a9-5 (CTB) - o3-1 (IG) | Always | Below 1 Ω |
| a9-5 (CTB) or o3-1 (IG) - Body ground | Always | 10 kΩ or higher |
| a9-6 (BBS) - o3-3 (BFB+) | Always | Below 1 Ω |
| a9-6 (BBS) or o3-3 (BFB+) - Body ground | Always | 10 kΩ or higher |
| o3-4 (GND) - a9-4 (BFB-) | Always | Below 1 Ω |
| o3-4 (GND) or a9-4 (BFB-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the seatback climate control blower RH with a new or known good one.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Seat Cushion Climate Control Blower Assembly RH) |
Disconnect the a9 seat cushion climate control blower assembly RH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a9-1 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| a9-1 (IG) - Body ground | Engine switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a9-8 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K54 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a9-7 (SIGN) - K54-23 (ROUT) | Always | Below 1 Ω |
| a9-7 (SIGN) or K54-23 (ROUT) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the K54 air conditioning amplifier assembly connector.
| *a | Component with harness connected
(Air Conditioning Amplifier Assembly) |
Reconnect the a9 seat cushion climate control blower assembly RH connector.
Using an oscilloscope, check the input signal waveform.
| Item | Content |
|---|---|
| Tester Connection | K54-23 (ROUT) - Body ground |
| Tool Setting | 1 V/DIV., 0.5 ms/DIV. |
| Vehicle Condition | ·
Engine switch on (IG) ·
Refreshing seat switch on (blower position) |
Waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the refreshing seat switch with a new or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Front Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | S/HTR F/R Relay |
Remove the S/HTR F/R relay from the No. 6 relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Battery voltage applied between terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | S/HTR F/R Relay Holder |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block S/HTR F/R relay terminal 1 - Body ground | Engine switch off | Below 1 V |
| No. 6 relay block S/HTR F/R relay terminal 1 - Body ground | Engine switch on (IG) | 11 to 14 V |
| No. 6 relay block S/HTR F/R relay terminal 5 - Body ground | Always | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | S/HTR F/R Relay Holder |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block S/HTR F/R relay terminal 3 - b8-1 (IG) | Always | Below 1 Ω |
| No. 6 relay block S/HTR F/R relay terminal 3 or b8-1 (IG) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | S/HTR F/R Relay Holder |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| No. 6 relay block S/HTR F/R relay terminal 2 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K49 refreshing seat switch connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K49-1 (IG) - Body ground | Engine switch on (IG) | 11 to 14 V |
| K49-1 (IG) - Body ground | Engine switch off | Below 1 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K49-5 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Temporarily replace the refreshing seat switch with a new or known good one.
Click hereVehicle Interior>SEAT>SEAT HEATER SWITCH (for Front Side)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Check the climate control seat operation.
Click hereVehicle Interior>SEAT>CLIMATE CONTROL SEAT SYSTEM>ON-VEHICLE INSPECTION
The climate control seat operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG