The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.
1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
2. DISCHARGE FUEL SYSTEM PRESSURE
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
55708
4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53607A
5.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for LHD)
53607A
6.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for RHD)
22030
7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
11209
8.REMOVE V-BANK COVER SUB-ASSEMBLY
12261
9.DISCONNECT VENTILATION HOSE
Slide the clip and disconnect the ventilation hose from the intake air surge tank assembly.
25860
10.DISCONNECT PURGE VALVE (PURGE VSV)
Disconnect the No. 1 fuel vapor feed hose from the intake air surge tank assembly.
Remove the bolt and disconnect the purge valve (purge VSV) from the intake air surge tank assembly.
17126
11.REMOVE NO. 2 SURGE TANK STAY
Remove the 2 bolts and No. 2 surge tank stay from the intake air surge tank assembly and camshaft housing RH.
17190
12.REMOVE INTAKE AIR SURGE TANK ASSEMBLY
Disconnect the vacuum switching valve (for ACIS) connector.
Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.
| *1 | Vacuum Hose Sub-assembly |
| *2 | Vacuum Hose |
| *3 | No. 2 Air Tube |
Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.
Disengage the clamp to disconnect the vacuum hose from the intake air surge tank assembly.
Disengage the clamp to disconnect the No. 2 air tube from the intake air surge tank assembly.
|
Bolt |
|
Nut |
Remove the 5 bolts, 2 nuts and intake air surge tank assembly from the intake manifold.
Remove the plug from the intake air surge tank assembly.
17176
13.REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET
Remove the air surge tank to intake manifold gasket from the intake air surge tank assembly.
11254
14.REMOVE NO. 1 V-BANK COVER BRACKET
Perform this procedure only when replacement of the No. 1 V-bank cover bracket is necessary.
Remove the 2 No. 1 V-bank cover brackets from the intake air surge tank assembly.
12327A
15.REMOVE NO. 2 ENGINE MOUNTING STAY RH
Remove the bolt and disconnect the wire harness clamp from the wire harness clamp bracket.
Remove the bolt and separate the wire harness clamp bracket from the No. 2 engine mounting stay RH.
|
Bolt |
|
Nut |
Remove the bolt, 2 nuts and No. 2 engine mounting stay RH from the engine mounting insulator sub-assembly RH.
Remove the bolt and No. 2 engine mounting stay RH from the intake manifold and front No.1 engine mounting bracket LH.
16.DISCONNECT FUEL TUBE SUB-ASSEMBLY
23800
17.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY
23807V
18.REMOVE NO. 1 DELIVERY PIPE SPACER
23291
19.REMOVE INJECTOR VIBRATION INSULATOR
17111
20.REMOVE INTAKE MANIFOLD
|
Bolt |
|
Nut |
Remove the 4 bolts, 4 nuts and intake manifold from the cylinder head sub-assembly.
17177
21.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET
Remove the 2 No. 1 intake manifold to head gaskets from each cylinder head sub-assembly.
22.REMOVE STUD BOLT
If a stud bolt is deformed or the threads are damaged, replace it.
Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the intake manifold.