Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › EXHAUST MANIFOLD
RM33A0E _51 Engine / Hybrid System _065336 2GR-FKS INTAKE / EXHAUST _0328629 EXHAUST MANIFOLD A

2GR-FKS INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold assembly RH (TWC: Front Catalyst) and exhaust manifold assembly LH (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 52239B 1.REMOVE BODY MOUNTING PLATE

Hide 17584B 2.REMOVE NO. 1 EXHAUST PIPE SUPPORT BRACKET (for Lower Side)

Hide 17410 3.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

a.
A408145

Disconnect the 2 heated oxygen sensor connectors.


b.

Disengage the 2 wire harness clamps.


c.
A408146

Remove the 4 bolts, 4 nuts and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst).


d.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust pipe support.


e.

Remove the 3 gaskets from the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 89467C 4.REMOVE AIR FUEL RATIO SENSOR (for Bank 1)

Hide 17167 5.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

a.
A408148

Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold assembly RH (TWC: Front Catalyst).


Hide 17141 6.REMOVE EXHAUST MANIFOLD ASSEMBLY RH (TWC: Front Catalyst)

a.
A408149

Using a 12 mm deep socket wrench, remove the 4 nuts and exhaust manifold assembly RH (TWC: Front Catalyst) from the cylinder head sub-assembly RH.


Hide 17173 7.REMOVE EXHAUST MANIFOLD TO HEAD GASKET (for Bank 1)

a.
A408150

Remove the exhaust manifold to head gasket (for Bank 1) from the cylinder head sub-assembly RH.


Hide 53852K 8.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 53851M 9.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 51441 10.REMOVE NO. 1 ENGINE UNDER COVER

Hide 11209 11.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 53295E 12.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 89467B 13.REMOVE AIR FUEL RATIO SENSOR (for Bank 2)

Hide 11452 14.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 17168 15.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A408151

Remove the 3 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold assembly LH (TWC: Front Catalyst).


Hide 17119 16.REMOVE NO. 2 MANIFOLD STAY

a.
A408152C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold assembly LH (TWC: Front Catalyst) and cylinder block sub-assembly.


Hide 16281F 17.DISCONNECT NO. 5 WATER BY-PASS HOSE

a.
A408275

Disengage the 2 clamps to disconnect the No. 5 water by-pass hose and No. 6 water by-pass hose from the hose clamp.


Hide 17150 18.REMOVE EXHAUST MANIFOLD ASSEMBLY LH (TWC: Front Catalyst)

a.
A408153

Using a 12 mm deep socket wrench, remove the 4 nuts and exhaust manifold assembly LH (TWC: Front Catalyst).


Hide 17173 19.REMOVE EXHAUST MANIFOLD TO HEAD GASKET (for Bank 2)

a.
A408154

Remove the exhaust manifold to head gasket (for Bank 2) from the cylinder head sub-assembly.


Hide 20.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A408155

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the exhaust manifold assembly LH (TWC: Front Catalyst).