Home › Engine / Hybrid System › 2AR-FE (INTAKE / EXHAUST) › EXHAUST MANIFOLD › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065327 2AR-FE INTAKE / EXHAUST _0328640 EXHAUST MANIFOLD A

2AR-FE INTAKE / EXHAUST  EXHAUST MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during exhaust manifold converter sub-assembly (TWC: Front Catalyst) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of air fuel ratio sensor

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A344783

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·
A344784

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.



PROCEDURE

Hide 57533B 1.REMOVE FRONT CENTER FLOOR BRACE

Hide 57523A 2.REMOVE CENTER FLOOR CROSSMEMBER BRACE

Hide 52239B 3.REMOVE BODY MOUNTING PLATE

Hide 17410 4.REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.


a.
A407104

Disconnect the heated oxygen sensor connector.


b.
A407105

Remove the 4 bolts, 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and center exhaust pipe assembly.


c.

Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.


d.

Remove the 2 gaskets from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and the front exhaust pipe assembly (TWC: Rear Catalyst).


Hide 17139 5.REMOVE NO. 2 MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A407107

Remove the bolt, nut and No. 2 manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.


Hide 17118 6.REMOVE MANIFOLD STAY

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A407106

Remove the bolt, nut and manifold stay from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and stiffening crankcase assembly.


Hide 17167 7.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A407108

Remove the 4 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 25051 9.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A407109

Remove the 5 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the cylinder head sub-assembly.


b.
A407110

Remove the exhaust manifold to head gasket from the cylinder head sub-assembly.


Hide 17168 10.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

a.
A407111

Remove the 2 bolts and No. 2 exhaust manifold heat insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).


Hide 25586 11.REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR

a.
A407112

Remove the 4 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).