Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0327417 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14B9  Open in Ion Generator Circuit  


DESCRIPTION

The ion generator sub-assembly operates when the blower switch is on. The air conditioning amplifier assembly sends a drive signal to the ion generator sub-assembly. When the ion generator sub-assembly receives the drive signal and starts to operate, it outputs an operation condition signal to the air conditioning amplifier assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14B9 Open in Ion Generator Circuit Open or short in ion generator circuit
·

Harness or connector

·

Ion generator sub-assembly

·

Air conditioning amplifier assembly


Memorized
(12 min. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E378349E01
2.667,0.917 2.979,1.115 0.313,0.198 10 false IG 3.438,0.917 3.75,1.115 0.313,0.198 10 false IG+ 2.656,2.156 2.969,2.354 0.313,0.198 10 false GND 3.385,2.156 3.698,2.354 0.313,0.198 10 false PCL 5.625,2.156 5.854,2.344 0.229,0.188 10 false IC 4.635,2.052 5.094,2.24 0.458,0.188 10 false NANO 4.635,0.813 5.094,1 0.458,0.188 10 false NAIN 4.365,0.813 4.604,1.01 0.24,0.198 10 false 26 4.427,2.052 4.594,2.25 0.167,0.198 10 false 7 3.771,2.063 3.938,2.26 0.167,0.198 10 false 2 2.479,2.073 2.646,2.271 0.167,0.198 10 false 4 2.448,0.813 2.615,1.01 0.167,0.198 10 false 1 3.75,0.823 3.917,1.021 0.167,0.198 10 false 3 1.594,1.063 2.615,1.24 1.021,0.177 10 false ECU-IG1 NO. 4 2.333,2.583 2.646,2.781 0.313,0.198 10 false Y1 2.354,2.74 4.177,2.948 1.823,0.208 10 false Ion Generator Sub-assembly 4.427,2.99 4.74,3.188 0.313,0.198 10 false K54 4.427,3.146 6.677,3.354 2.25,0.208 10 false Air Conditioning Amplifier Assembly 5.813,0.365 6.125,0.552 0.313,0.188 10 false 5 V 0.375,0.917 1.313,1.271 0.938,0.354 10 false from IG1-NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Air Conditioner > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Ion Generator Ion generator sub-assembly OFF or ON -
Body Electrical > Air Conditioner > Active Test
Tester Display
Ion Generator
50004 121 94
OK:

Ion generator sub-assembly operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - IG POWER SOURCE AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - IG POWER SOURCE AND BODY GROUND)
a.

Disconnect the Y1 ion generator sub-assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Y1-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Y1-1 (IG) - Body ground Ignition switch off Below 1 V


Standard Resistance:
Tester Connection Condition Specified Condition
Y1-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ION GENERATOR SUB-ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Y1-3 (IG+) - K54-26 (NAIN) Always Below 1 Ω
Y1-2 (PCL) - K54-7 (NANO) Always Below 1 Ω
Y1-3 (IG+) or K54-26 (NAIN) - Other terminals and body ground Always 10 kΩ or higher
Y1-2 (PCL) or K54-7 (NANO) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY COMMUNICATION POWER SUPPLY

NG

REPAIR OR REPLACE HARNESS AND CONNECTOR

4.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY COMMUNICATION POWER SUPPLY
a.

Reconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Y1-3 (IG+) - Body ground
·

Ignition switch ON

·

Blower switch off


4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

5.CHECK ION GENERATOR SUB-ASSEMBLY OUTPUT

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.CHECK ION GENERATOR SUB-ASSEMBLY OUTPUT
E328993C39
1.75,0.26 2.167,0.5 0.417,0.24 1.885,1.844 1.635,1.354 true 0.094,0.094 0.406,0.25 0.313,0.156 10 false *a 1.865,0.313 2.177,0.469 0.313,0.156 10 false K54 1.771,1.865 2.177,2.021 0.406,0.156 10 false NAIN
*a Component with harness connected
(Air Conditioning Amplifier Assembly)


a.

Reconnect the Y1 ion generator sub-assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
K54-26 (NAIN) - Body ground
·

Ignition switch ON

·

Blower switch off


Below 2.2 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE ION GENERATOR SUB-ASSEMBLY