Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0327417 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  B14B3  Lost Communication with Rear Panel LIN  


DESCRIPTION

The cooler control switch assembly communicates with the air conditioning amplifier assembly via LIN communication.

If a malfunction occurs in the LIN communication system, the air conditioning amplifier assembly will not operate, even if the cooler control switch assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14B3 Lost Communication with Rear Panel LIN Lost communication with cooler control switch assembly
·

Harness or connector

·

Cooler control switch assembly

·

Air conditioning amplifier assembly


Memorized
(10 sec. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E378490E01
1.729,0.417 2.042,0.615 0.313,0.198 10 false +B 1.688,1.438 2,1.635 0.313,0.198 10 false IG+ 1.625,0.927 1.938,1.125 0.313,0.198 10 false ACC 1.615,1.958 1.927,2.156 0.313,0.198 10 false GND 1.604,2.469 1.917,2.667 0.313,0.198 10 false RLIN 5.25,2.49 5.563,2.688 0.313,0.198 10 false LIN1 2.031,0.313 2.208,0.479 0.177,0.167 10 false 9 2.021,0.823 2.198,0.99 0.177,0.167 10 false 1 2.021,1.313 2.198,1.479 0.177,0.167 10 false 10 2.021,1.854 2.198,2.021 0.177,0.167 10 false 16 2.021,2.344 2.198,2.51 0.177,0.167 10 false 13 4.969,2.344 5.146,2.51 0.177,0.167 10 false 14 0.979,3.385 2.625,3.594 1.646,0.208 10 false : LIN Communication Line 0.479,2.813 0.708,3 0.229,0.188 10 false Z1 0.469,2.969 2.563,3.177 2.094,0.208 10 false Cooler Control Switch Assembly 4.677,2.896 5,3.073 0.323,0.177 10 false K54 4.677,3.052 6.958,3.25 2.281,0.198 10 false Air Conditioning Amplifier Assembly 2.208,0.552 3.135,0.74 0.927,0.188 10 false ECU-B NO. 2 2.219,1.583 3.188,1.771 0.969,0.188 10 false ECU-IG1 NO. 4 2.24,1.073 3.167,1.26 0.927,0.188 10 false ECU-ACC 3.771,0.417 4.698,0.604 0.927,0.188 10 false from Battery 3.781,1.438 5.208,1.635 1.427,0.198 10 false from IG1-NO. 1 Relay 3.781,0.917 4.917,1.115 1.135,0.198 10 false from ACC Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.

Disconnect the Z1 cooler control switch assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Z1-9 (+B) - Body ground Always 11 to 14 V
Z1-1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Z1-10 (IG+) - Body ground Ignition switch ON 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
Z1-16 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (COOLER CONTROL SWITCH ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z1-13 (RLIN) - K54-14 (LIN1) Always Below 1 Ω
Z1-13 (RLIN) or K54-14 (LIN1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
E334619N03
0.302,1.563 0.76,1.76 0.458,0.198 10 false GND

a.

Connect the K54 air conditioning amplifier assembly connector.


b.

Turn the ignition switch to ON.


c.

Using an oscilloscope, check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Terminal No. K54-14 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON


Result:
Proceed to
OK
NG



OK

4.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

4.INSPECT AIR CONDITIONING CONTROL ASSEMBLY
E378489C01
1.615,0.188 1.896,0.427 0.281,0.24 1,2.313 1.167,2.313 1.167,2.313 1.656,1.438 true 0.188,0.208 0.385,0.406 0.198,0.198 10 false *a 1.677,0.208 1.875,0.406 0.198,0.198 10 false Z1 0.677,2.229 1.042,2.417 0.365,0.188 10 false RLIN 0.344,3.917 0.708,4.104 0.365,0.188 10 false GND
*a Component with harness connected
(Cooler Control Switch Assembly)


a.

Connect the Z1 cooler control switch assembly connector.


b.

Turn the ignition switch to ON.


c.

Using an oscilloscope, check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Terminal No. Z1-13 (RLIN) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE COOLER CONTROL SWITCH ASSEMBLY