Home › Power Source / Network › 2GR-FKS (BATTERY / CHARGING) › GENERATOR
RM33A0E _57 Power Source / Network _065340 2GR-FKS BATTERY / CHARGING _0328814 GENERATOR A

2GR-FKS BATTERY / CHARGING  GENERATOR  DISASSEMBLY  


PROCEDURE

Hide 27416 1.REMOVE GENERATOR PULLEY CAP

a.
A407299

Using a screwdriver, remove the generator pulley cap from the generator pulley with clutch.

NOTICE:
·

Do not reuse the generator pulley cap.

·

If the generator pulley cap is removed, replace the generator pulley cap and generator pulley with clutch with new ones as the correct grease amount cannot be confirmed.



HINT:

Although grease will be observed when the generator pulley cap is removed, this does not indicate a malfunction.



Hide 2.REMOVE GENERATOR REAR END COVER

a.
A407300

Remove the 3 bolts and generator rear end cover from the generator coil assembly.


Hide 3.REMOVE GENERATOR TERMINAL INSULATOR

a.
A407301

Remove the generator terminal insulator from the generator coil assembly.


Hide 4.REMOVE GENERATOR BRUSH HOLDER ASSEMBLY

a.
A407302

Remove the 2 screws and generator brush holder assembly from the generator coil assembly.


Hide 5.REMOVE GENERATOR COIL ASSEMBLY

a.
A407303

Remove the 4 bolts.


b.
A118275C09
2.125,0.771 2.646,0.771 false 0.677,0.594 1.115,0.115 1.115,0.115 1.26,0.115 false 2.688,0.719 3.042,0.99 0.354,0.271 10 false SST 1.313,0.052 1.635,0.323 0.323,0.271 10 false SST 2.552,0.344 2.823,0.604 0.271,0.26 10 false *a 0.125,1.844 0.438,2.042 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, remove the generator coil assembly from the generator rotor assembly.

SST
09950-40011  (09951-04020, 09952-04010, 09953-04020, 09954-04010, 09955-04071, 09957-04010, 09958-04011)


c.
A401900

Remove the bearing cover packing.

NOTICE:

If the bearing cover packing breaks, remove the broken pieces completely.


HINT:

The bearing cover packing may be installed on the generator rotor assembly.



Hide 27415 6.REMOVE GENERATOR PULLEY WITH CLUTCH

a.

Secure the generator drive end frame in a vise between aluminum plates.


b.
A407304C01
1.375,0.313 1.583,0.313 1.583,0.313 2.031,0.771 true 1.031,2.167 1.313,3.24 1.313,3.24 1.521,3.24 true 1.906,2.365 1.906,2.073 false 3,1.885 3,1.115 true 1.229,0.219 1.542,0.375 0.313,0.156 10 false *a 1.552,3.135 2.323,3.333 0.771,0.198 10 false SST B 1.771,2.375 2.542,2.573 0.771,0.198 10 false SST A 2.76,1.906 3.313,2.125 0.552,0.219 10 false SST A
*a Rotor Shaft


Install SST (A) and (B) to the generator pulley with clutch as shown in the illustration.

SST
09820-63021  

NOTICE:

Securely attach SST to the generator pulley with clutch and rotor shaft.



c.
A407305C01
2.51,1.354 2.719,0.813 2.719,0.813 2.875,0.813 false 2.167,0.969 2.375,0.427 2.375,0.427 2.531,0.427 false 0.802,2.813 1.021,3 0.219,0.188 10 true *a 1.906,1.958 2.146,2.135 0.24,0.177 10 true *b 2.906,0.719 3.396,0.969 0.49,0.25 10 false SST A 2.563,0.333 3.052,0.583 0.49,0.25 10 false SST B
*a Turn
*b Hold


Loosen the generator pulley with clutch by turning SST (B) as shown in the illustration.

NOTICE:
·

Check that the generator drive end frame is secured in the vise tightly.


·

Hold SST (A) tightly during the operation.




d.

Remove SST from the generator pulley with clutch.


e.

Remove the generator pulley with clutch from the rotor shaft.


Hide 7.REMOVE GENERATOR ROTOR ASSEMBLY

a.
A300641

Remove the generator rotor assembly from the generator drive end frame.


Hide 8.INSPECT GENERATOR DRIVE END FRAME BEARING

Hide 9.REMOVE GENERATOR DRIVE END FRAME BEARING

a.
A128076

Remove the 4 screws and retainer plate from the generator drive end frame.


b.
A407312E01
1.208,1.208 0.365,0.802 0.365,0.802 1.25,0.917 true 0.104,0.719 0.563,0.917 0.458,0.198 10 false SST

Using SST and a hammer, tap out the generator drive end frame bearing from the generator drive end frame.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)