Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › REAR VIEW MONITOR SYSTEM
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0328875 REAR VIEW MONITOR SYSTEM C

PARK ASSIST / MONITORING  REAR VIEW MONITOR SYSTEM  C1622  Back Camera Disconnected  


DESCRIPTION

This DTC is stored if the radio and display receiver assembly judges that the signals or signal lines between the radio and display receiver assembly and the rear television camera assembly are not normal as a result of its self check.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1622 Back Camera Disconnected Open or short in the rear television camera assembly signal circuit
·

Harness or connector

·

Rear television camera assembly

·

Radio and display receiver assembly



WIRING DIAGRAM

E365933E03
0.531,3.01 5.885,3.208 5.354,0.198 10 false Radio and Display Receiver Assembly 1.906,0.615 2.365,0.813 0.458,0.198 10 false CA+ 2,1 2.313,1.198 0.313,0.198 10 false V+ 2.021,1.375 2.333,1.573 0.313,0.198 10 false V- 1.802,1.802 2.417,2 0.615,0.198 10 false CGND 1.833,2.208 2.448,2.406 0.615,0.198 10 false CSLD 1.823,2.594 2.438,2.792 0.615,0.198 10 false GND1 2.375,0.615 2.688,0.813 0.313,0.198 10 false K2 2.375,1.01 2.688,1.208 0.313,0.198 10 false K2 2.375,1.396 2.688,1.594 0.313,0.198 10 false K2 2.375,1.802 2.688,2 0.313,0.198 10 false K2 2.375,2.208 2.688,2.406 0.313,0.198 10 false K2 2.375,2.615 2.688,2.813 0.313,0.198 10 false K3 2.375,0.406 2.688,0.604 0.313,0.198 10 false 30 2.385,0.813 2.698,1.01 0.313,0.198 10 false 28 2.385,1.208 2.698,1.406 0.313,0.198 10 false 29 2.385,1.604 2.698,1.802 0.313,0.198 10 false 27 2.385,2.01 2.698,2.208 0.313,0.198 10 false 26 2.417,2.417 2.573,2.615 0.156,0.198 10 false 1 3.656,2 3.813,2.198 0.156,0.198 10 false * 5.125,0.615 5.583,0.813 0.458,0.198 10 false CB+ 5.125,1 5.583,1.198 0.458,0.198 10 false CV+ 5.135,1.396 5.594,1.594 0.458,0.198 10 false CV- 5.135,1.792 5.75,1.99 0.615,0.198 10 false CGND 4.896,0.5 5.052,0.698 0.156,0.198 10 false 6 4.896,0.896 5.052,1.094 0.156,0.198 10 false 3 4.896,1.292 5.052,1.49 0.156,0.198 10 false 2 4.896,1.677 5.052,1.875 0.156,0.198 10 false 5 4.698,2.49 6.979,2.781 2.281,0.292 10 false Rear Television Camera Assembly 4.698,2.25 5.01,2.448 0.313,0.198 10 false m1 4.771,3.146 6.458,3.344 1.688,0.198 10 false *: Shielded

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR TELEVISION CAMERA ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the m1 rear television camera assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-30 (CA+) - m1-6 (CB+) Always Below 1 Ω
K2-28 (V+) - m1-3 (CV+) Always Below 1 Ω
K2-29 (V-) - m1-2 (CV-) Always Below 1 Ω
K2-27 (CGND) - m1-5 (CGND) Always Below 1 Ω
K2-26 (CSLD) - Body ground Always Below 1 Ω
K2-30 (CA+) or m1-6 (CB+) - Body ground Always 10 kΩ or higher
K2-28 (V+) or m1-3 (CV+) - Body ground Always 10 kΩ or higher
K2-29 (V-) or m1-2 (CV-) - Body ground Always 10 kΩ or higher
K2-27 (CGND) or m1-5 (CGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Reconnect the K2 radio and display receiver assembly connector.


b.
E366062C02
1.427,0.198 1.917,0.479 0.49,0.281 0.542,1.073 1.042,1.344 true 0.771,1.76 1.167,1.375 true 1.333,1.875 1.438,1.375 true 1.583,0.25 1.896,0.448 0.313,0.198 10 false K2 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a 0.344,0.875 0.802,1.073 0.458,0.198 10 false CA+ 0.635,1.771 0.948,1.969 0.313,0.198 10 false V- 1.156,1.896 1.771,2.094 0.615,0.198 10 false CGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-29 (V-) - Body ground Always Below 1 Ω
K2-27 (CGND) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-30 (CA+) - K2-27 (CGND) Engine switch on (ACC) 5.5 to 7.05 V



Result:
Proceed to
OK
NG



OK

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

3.INSPECT REAR TELEVISION CAMERA ASSEMBLY
a.

Reconnect the m1 rear television camera assembly connector.


b.
E366063C02
1.427,0.448 1.979,0.698 0.552,0.25 1.438,2.594 1.99,2.844 0.552,0.25 0.958,2.115 1.26,1.604 true 2.344,3.385 2.646,2.875 true 1.604,0.479 1.917,0.677 0.313,0.198 10 false K2 1.615,2.635 1.927,2.833 0.313,0.198 10 false K3 0.844,2.146 1.156,2.344 0.313,0.198 10 false V+ 2.542,2.688 3.156,2.885 0.615,0.198 10 false GND1 0.24,0.24 0.552,0.438 0.313,0.198 10 false *a
*a Component with harness connected
(Radio and Display Receiver Assembly)


E265840C01
0.823,2.073 1,2.073 1,2.073 1.125,1.583 false 1.479,2.063 1.344,2.063 1.344,2.063 1.229,1.479 false 0.781,4.167 0.958,4.167 0.958,4.167 1.156,3.594 false 1.521,4.125 1.385,4.125 1.385,4.125 1.271,3.542 false 0.229,0.229 0.542,0.427 0.313,0.198 10 *a 0.396,1.052 0.76,1.313 0.365,0.26 10 GND 0.396,3.208 0.76,3.469 0.365,0.26 10 GND 0.26,2.271 0.625,2.531 0.365,0.26 10 *b 0.646,4.073 1.01,4.333 0.365,0.26 10 *c 0.656,1.979 1.021,2.24 0.365,0.26 10 *c 1.51,1.969 1.875,2.229 0.365,0.26 10 *d 1.542,4.052 1.906,4.313 0.365,0.26 10 *d
*a Waveform 1 (camera lens is not covered, displaying an image)
*b Waveform 2 (camera lens is covered, blacking out the screen)
*c Synchronization Signal
*d Video Waveform


Using an oscilloscope, check the waveform of the rear television camera assembly.

HINT:

A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the radio and display receiver assembly with the connector connected.


OK:

Waveform is similar to that shown in the illustration.


Item Content
Measurement terminal K2-28 (V+) - K3-1 (GND1)
Measurement setting 200 mV/DIV., 50 μs./DIV.
Condition Engine switch on (IG), shift lever in R

HINT:
·

The video waveform changes according to the image sent by the rear television camera assembly.

·

The video waveform is constantly output when the engine switch is turned on (ACC).




Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG