Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM
RM33A0E _56 Audio / Visual / Telematics _065375 PARK ASSIST / MONITORING _0328876 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Buzzer does not Sound  


WIRING DIAGRAM

E254403E93
0.167,1.01 1.573,1.208 1.406,0.198 10 false from IG1-NO. 1 Relay 3.5,1 3.792,1.198 0.292,0.198 10 false BZP 3.125,1.302 3.469,1.5 0.344,0.198 10 false R26 3.125,1.479 5.135,1.896 2.01,0.417 10 false RCTA Buzzer (Blind Spot Monitor Buzzer) 5.615,1.927 5.906,2.125 0.292,0.198 10 false W6 5.615,2.083 6.813,2.448 1.198,0.365 10 false Blind Spot Monitor Sensor LH 4.333,1.01 4.667,1.208 0.333,0.198 10 false BZN 3.333,0.906 3.479,1.083 0.146,0.177 10 false 1 5.646,1.021 5.979,1.219 0.333,0.198 10 false BUZ 5.469,0.917 5.615,1.094 0.146,0.177 10 false 3 4.677,0.917 4.823,1.094 0.146,0.177 10 false 2 2.021,1.177 3.198,1.469 1.177,0.292 10 false ECU-IG1 NO.4

CAUTION / NOTICE / HINT

NOTICE:
·

When checking for DTCs, make sure that the blind spot monitor system is turned on.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER)
a.

Check that the RCTA buzzer (blind spot monitor buzzer) sounds when the initial check is performed.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>SYSTEM DESCRIPTION

OK:

RCTA buzzer sounds



Result:
Proceed to
OK
NG



OK

NG

2.CHECK DTC
2.CHECK DTC
a.

Turn the engine switch off.


b.

Turn the engine switch on (IG).


c.

Recheck for DTCs and check if the same DTC is output again.

Body Electrical > Blind Spot Monitor Slave > Trouble Codes
50001 314
OK:

No DTCs are output.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH)

NG

3.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the R26 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R26-1 (BZP) - Body ground Engine Switch on (IG) 11 to 14 V
R26-2 (BZN) or W6-3 (BUZ) - Body ground Below 1 V
R26-2 (BZN) - R26-1 (BZP) Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH AND BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH AND BATTERY)
a.

Disconnect the R26 RCTA buzzer (blind spot monitor buzzer) connector.


b.

Disconnect the W6 blind spot monitor sensor LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R26-2 (BZN) - W6-3 (BUZ) Always Below 1 Ω
R26-2 (BZN) or W6-3 (BUZ) - Body ground Always 10 kΩ or higher



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R26-2 (BZN) or W6-3 (BUZ) - Body ground Engine switch on (IG) Below 1 V
R26-1 (BZP) - Body ground Engine switch on (IG) 11 to 14 V
R26-1 (BZP) - Body ground Engine switch off Below 1 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR