The main body ECU (multiplex network body ECU) receives switch signals from the door key lock and unlock switch (front door lock with motor assembly) and driver door key cylinder lock or unlock switch signals from the front door lock with motor assembly. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.
for LHD
for RHD
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*
*: w/ Smart Entry and Start System
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*: w/ Door Control Battery
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Key SW-Lock | Driver door key-linked lock / unlock switch lock signal | OFF or ON | OFF: Driver door key cylinder not turned to lock position
ON: Driver door key cylinder turned to lock position |
- |
| D Door Key SW-UL | Driver door key-linked lock / unlock switch unlock signal | OFF or ON | OFF: Driver door key cylinder not turned to unlock position
ON: Driver door key cylinder turned to unlock position |
- |
| Tester Display |
|---|
| Door Key SW-Lock |
| D Door Key SW-UL |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD
Remove the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly LH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
for RHD
Remove the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL
Inspect the front door lock with motor assembly RH.
Click hereVehicle Interior>DOOR LOCK>FRONT DOOR LOCK>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
for LHD
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O15-9 (L) - K53-18 (L2) | Always | Below 1 Ω |
| O15-10 (UL) - K53-17 (UL3) | Always | Below 1 Ω |
| O15-7 (E) - Body ground | Always | Below 1 Ω |
| O15-9 (L) or K53-18 (L2) - Other terminals and body ground | Always | 10 kΩ or higher |
| O15-10 (UL) or K53-17 (UL3) - Other terminals and body ground | Always | 10 kΩ or higher |
for RHD
Disconnect the K53 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N15-6 (L) - K53-18 (L2) | Always | Below 1 Ω |
| N15-5 (UL) - K53-17 (UL3) | Always | Below 1 Ω |
| N15-7 (E) - Body ground | Always | Below 1 Ω |
| N15-6 (L) or K53-18 (L2) - Other terminals and body ground | Always | 10 kΩ or higher |
| N15-5 (UL) or K53-17 (UL3) - Other terminals and body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG