Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.09–2018.04
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0327182 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1380  Stop Light Control Relay Malfunction  


DESCRIPTION

When the skid control ECU (brake actuator assembly) applies the brakes after receiving a brake request signal from the pre-collision system, dynamic radar cruise control system, secondary collision brake system or brake hold control system, the skid control ECU (brake actuator assembly) operates the stop light control relay (stop light switch assembly) to illuminate the stop lights.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1380 Stop Light Control Relay Malfunction Either condition is met:
·

When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is on, a signal is not input to the STP terminal for 5 seconds or more.

·

When the voltage at the +BS terminal is between 10 V or more and the stop light control relay (stop light switch assembly) drive output (STPO) is off, the signal at the STP2 terminal is different from the input signal at the STP terminal for 5 seconds or more.


·

Wire harness or connector

·

Stop light switch assembly

·

Skid control ECU (brake actuator assembly)

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light (center stop light set)

·

Shift lock control ECU (shift lock control unit assembly)

·

Certification ECU (smart key ECU assembly)

·

ECM



DTC Detection Conditions: C1380
Vehicle Condition
Pattern 1 Pattern 2
Diagnosis Condition The voltage at the +BS terminal is between 10 V or more. ○ ○
Malfunction Status When the stop light control relay (stop light switch assembly) drive output (STPO) is on, a signal is not input to the STP terminal. ○ -
When the stop light control relay (stop light switch assembly) drive output (STPO) is off, the signal at the STP2 terminal is different from the input signal at the STP terminal. - ○
Detection Time 5 seconds or more 5 seconds or more
Number of Trips 1 trip 1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C385671E02
3.333,8.594 4.385,8.813 1.052,0.219 10 false *3: for 2AR-FE 0.927,8 3.552,8.229 2.625,0.229 10 false Rear Combination Light Assembly RH 0.917,6.844 3.542,7.073 2.625,0.229 10 false Rear Combination Light Assembly LH 0.167,9.167 2.583,9.417 2.417,0.25 10 false *4: w/ Smart Entry and Start System 0.177,8.583 1.302,8.802 1.125,0.219 10 false *1: for 2GR-FKS 1.75,8.594 2.938,8.792 1.188,0.198 10 false *2: for A25A-FKS 3.135,9.167 5.719,9.417 2.583,0.25 10 false *5: w/o Smart Entry and Start System 0.948,2.646 1.833,2.865 0.885,0.219 10 false from Battery 4.01,7.99 6.625,8.25 2.615,0.26 10 false Center Stop Light (Center Stop Light Set) 4,6 6.927,6.198 2.927,0.198 10 false Skid Control ECU (Brake Actuator Assembly) 1.417,5.792 3.24,5.979 1.823,0.188 10 false Stop Light Switch Assembly 0.167,0.844 3.865,1.083 3.698,0.24 10 false Shift Lock Control ECU (Shift Lock Control Unit Assembly) 4.01,1.01 7.083,1.25 3.073,0.24 10 false Certification ECU (Smart Key ECU Assembly) *4 2.552,0.375 3.01,0.573 0.458,0.198 10 false STP 2.229,1.698 2.688,1.896 0.458,0.198 10 false STP 4.958,0.385 5.417,0.583 0.458,0.198 10 false STP1 1.917,2.135 2.375,2.333 0.458,0.198 10 false ECM 2.917,0.396 3.219,0.594 0.302,0.198 10 false K27 3.24,0.396 3.542,0.594 0.302,0.198 10 false K28 3.24,1.698 3.542,1.896 0.302,0.198 10 false A22 2.573,1.698 2.875,1.896 0.302,0.198 10 false A23 2.906,1.698 3.208,1.896 0.302,0.198 10 false A24 4.021,0.854 4.323,1.052 0.302,0.198 10 false R8 2.604,1.906 2.906,2.104 0.302,0.198 10 false *1 2.948,1.906 3.25,2.104 0.302,0.198 10 false *2 3.281,1.906 3.583,2.104 0.302,0.198 10 false *3 2.615,1.5 2.917,1.698 0.302,0.198 10 false 27 2.948,1.5 3.25,1.698 0.302,0.198 10 false 21 3.333,1.5 3.635,1.698 0.302,0.198 10 false 9 2.948,0.604 3.25,0.802 0.302,0.198 10 false *4 3.281,0.604 3.583,0.802 0.302,0.198 10 false *5 3,0.198 3.302,0.396 0.302,0.198 10 false 4 3.333,0.198 3.635,0.396 0.302,0.198 10 false 8 4.646,0.313 4.948,0.51 0.302,0.198 10 false 25 0.76,3.688 1.219,3.885 0.458,0.198 10 false STOP 1.979,6.573 2.438,6.771 0.458,0.198 10 false Stop 1.969,7.75 2.427,7.948 0.458,0.198 10 false Stop 1.542,5.25 2,5.448 0.458,0.198 10 false GND 2.75,5.25 3.208,5.448 0.458,0.198 10 false OUT 2.76,4.24 3.219,4.438 0.458,0.198 10 false ACC 1.542,3.667 2,3.865 0.458,0.198 10 false B 2.917,3.344 3.375,3.542 0.458,0.198 10 false L 4.719,3.333 5.177,3.531 0.458,0.198 10 false STP 4.708,4.24 5.167,4.438 0.458,0.198 10 false STPO 4.719,5.25 5.177,5.448 0.458,0.198 10 false STP2 4.5,5.01 4.802,5.208 0.302,0.198 10 false 44 4.49,4.01 4.792,4.208 0.302,0.198 10 false 10 4.49,3.104 4.792,3.302 0.302,0.198 10 false 42 4.031,5.833 4.333,6.031 0.302,0.198 10 false A34 0.917,6.667 1.333,6.865 0.417,0.198 10 false W13 4.01,7.823 4.313,8.021 0.302,0.198 10 false R47 0.948,7.823 1.344,8.021 0.396,0.198 10 false W12 1.417,5.635 1.719,5.833 0.302,0.198 10 false A37 2.417,7.479 2.875,7.677 0.458,0.198 10 false STP 2.406,6.323 2.865,6.521 0.458,0.198 10 false STP 4.958,7.479 5.417,7.677 0.458,0.198 10 false B 5.906,7.479 6.365,7.677 0.458,0.198 10 false E 1.615,7.479 2.073,7.677 0.458,0.198 10 false E 1.615,6.323 2.073,6.521 0.458,0.198 10 false E 1.083,3.417 1.542,3.615 0.458,0.198 10 false 2 0.729,3.417 1.188,3.615 0.458,0.198 10 false 1 1.406,3.427 1.865,3.625 0.458,0.198 10 false 7 6.094,7.479 6.552,7.677 0.458,0.198 10 false 2 3.125,4.021 3.583,4.219 0.458,0.198 10 false 4 3.125,5 3.583,5.198 0.458,0.198 10 false 1 3.125,3.083 3.583,3.281 0.458,0.198 10 false 3 1.458,7.479 1.917,7.677 0.458,0.198 10 false 4 2.74,6.323 3.198,6.521 0.458,0.198 10 false 2 2.75,7.479 3.208,7.677 0.458,0.198 10 false 2 1.458,6.333 1.917,6.531 0.458,0.198 10 false 4 4.792,7.479 5.25,7.677 0.458,0.198 10 false 1 1.406,5.021 1.656,5.208 0.25,0.188 10 false 2

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS (BS1 VOLTAGE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
BS1 Voltage Value +BS voltage value Min.: 0.00 V, Max.: 20.00 V - Changes in proportion to battery voltage
Chassis > ABS/VSC/TRC > Data List
Tester Display
BS1 Voltage Value
50003 105 273

d.

Take a note of the +BS voltage value.

HINT:

The noted +BS voltage value is used in a later step.



Result:
Proceed to
NEXT



NEXT

2.CHECK HARNESS AND CONNECTOR (STP2, STPO AND STP TERMINAL)
2.CHECK HARNESS AND CONNECTOR (STP2, STPO AND STP TERMINAL)
a.
C360727C72
0.208,0.26 0.708,0.51 0.5,0.25 2.792,0.354 2.448,0.938 true 1.719,0.344 2.156,0.938 true 1.99,1.302 1.604,1.854 true 0.063,0.042 0.375,0.198 0.313,0.156 10 false *a 0.333,0.302 0.688,0.5 0.354,0.198 10 false A34 1.438,1.865 1.979,2.042 0.542,0.177 10 false STPO 2.708,0.167 3.167,0.344 0.458,0.177 10 false STP2 1.542,0.167 2.083,0.344 0.542,0.177 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

Disconnect the A34 skid control ECU (brake actuator assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V
A34-10 (STPO) - Body ground Always 11 to 14 V
A34-44 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-44 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Result Proceed to
All terminal voltages are normal A
Only STP terminal voltage abnormal B
Only STPO terminal voltage abnormal C
Only STP2 terminal voltage abnormal D
STPO terminal and STP2 terminal voltage abnormal E



A

3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

B

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)

C

11.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

D

12.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

E

17.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
3.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Reconnect the A34 skid control ECU (brake actuator assembly) connector.


b.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5
OK:

Stop light turns ON/OFF in response to the GTS operation



Result:
Proceed to
OK
NG



OK

4.CHECK FOR DTC

NG

5.INSPECT BRAKE ACTUATOR ASSEMBLY
4.CHECK FOR DTC
a.

Clear the DTCs.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

c.

According to the display on the GTS, perform the Active Test.


d.

Check if the same DTC is output.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

Result:
Result Proceed to
C1380 is output A
C1380 is not output B



A

B

5.INSPECT BRAKE ACTUATOR ASSEMBLY
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on
Chassis > ABS/VSC/TRC > Active Test
Tester Display
Stop Light Relay
50004 105 5

b.
E233300C72
1.427,0.271 1.917,0.563 0.49,0.292 1.688,1.115 1.167,1.677 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.542,0.333 1.99,0.594 0.448,0.26 10 false A37 1,1.698 1.448,1.958 0.448,0.26 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-4 (ACC) - Body ground Active Test is on Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the K27 shift lock control ECU (shift lock control unit assembly) connector (w/ Smart Entry and Start System).


c.

Disconnect the K28 shift lock control ECU (shift lock control unit assembly) connector (w/o Smart Entry and Start System).


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A23 ECM connector (for 2GR-FKS).


c.

Disconnect the A24 ECM connector (for A25A-FKS).


d.

Disconnect the A22 ECM connector (for 2AR-FE).


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Result Proceed to
OK A
NG (w/ Smart Entry and Start System) B
NG (w/o Smart Entry and Start System) C



A

B

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SMART KEY ECU ASSEMBLY)

C

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the R8 certification ECU (smart key ECU assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-42 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C360727C71
0.271,0.281 0.719,0.531 0.448,0.25 2.563,0.365 2.208,0.927 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.365,0.323 0.708,0.542 0.344,0.219 10 false A34 2.479,0.188 2.906,0.375 0.427,0.188 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-42 (STP) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-42 (STP) - A37-3 (L) Always Below 1 Ω
A34-42 (STP) or A37-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-10 (STPO) - A37-4 (ACC) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
C360727C73
0.292,0.281 0.74,0.531 0.448,0.25 2.792,0.375 2.438,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.375,0.323 0.719,0.542 0.344,0.219 10 false A34 2.698,0.208 3.125,0.396 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the W13 rear combination light assembly LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-44 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-44 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

NG

13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
13.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
C360727C73
0.292,0.281 0.74,0.531 0.448,0.25 2.792,0.375 2.438,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.375,0.323 0.719,0.542 0.344,0.219 10 false A34 2.698,0.208 3.125,0.396 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the W12 rear combination light assembly RH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-44 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-44 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

NG

14.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - CENTER STOP LIGHT SET)
14.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - CENTER STOP LIGHT SET)
a.
C360727C73
0.292,0.281 0.74,0.531 0.448,0.25 2.792,0.375 2.438,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.375,0.323 0.719,0.542 0.344,0.219 10 false A34 2.698,0.208 3.125,0.396 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the R47 center stop light (center stop light set) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-44 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) (+BS x 0.85) to 14 V*
A34-44 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



Result:
Proceed to
OK
NG



OK

NG

15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
15.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
C360727C73
0.292,0.281 0.74,0.531 0.448,0.25 2.792,0.375 2.438,0.938 true 0.115,0.083 0.427,0.24 0.313,0.156 10 false *a 0.375,0.323 0.719,0.542 0.344,0.219 10 false A34 2.698,0.208 3.125,0.396 0.427,0.188 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A34-44 (STP2) - Body ground Always Below 1.5 V



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-1 (OUT) - A34-44 (STP2) Always Below 1 Ω
A37-1 (OUT) or A34-44 (STP2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
a.
E360372C05
1.427,0.333 1.927,0.583 0.5,0.25 1.281,1.188 1,1.75 true 2.25,1.188 2.583,1.75 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.552,0.375 2.01,0.531 0.458,0.156 10 false A37 0.844,1.76 1.26,1.958 0.417,0.198 10 false GND 2.552,1.76 2.969,1.958 0.417,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-2 (GND) - Body ground Always Below 1 Ω



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-7 (B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A34-10 (STPO) or A37-4 (ACC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR