Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › ECM › 2017.09–2018.04
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0319008 ECM A

2AR-FE ENGINE CONTROL  ECM  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed, or replaced during the ECM removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

*2: w/o Smart Entry and Start System

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)
Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
ECM (If possible, read the transaxle compensation code from the previous ECM) Possible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

The deterioration of fuel efficiency


(Click here)for U760E Initialization
(Click here)for U760E Registration
Impossible Perform the following procedures in the order shown:
1.

Reset Memory

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM*1 Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.
Replacement of ECM*2 Perform code registration (Immobiliser system)
·

Wireless door lock control system

·

Engine start


See Service Bulletin for the registration method.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

If the ECM has been struck or dropped, replace it.

·

Perform the Vehicle Identification Number (VIN) or frame number registration when replacing the ECM.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>REGISTRATION



PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 53295E 2.REMOVE COOL AIR INTAKE DUCT SEAL

Hide 17750A 3.REMOVE INLET AIR CLEANER ASSEMBLY

Hide 17700 4.REMOVE AIR CLEANER ASSEMBLY

a.
A405017

Disconnect the mass air flow meter sub-assembly connector.


b.

Disengage the 3 wire harness clamps.


c.
A405018

Loosen the hose clamp and remove the air cleaner hose assembly from the air cleaner assembly.


d.

Disengage the 3 pins to remove the air cleaner assembly.


Hide 89661 5.REMOVE ECM

a.
A405020

Rotate the 2 levers while pushing the locks, and disconnect the 2 ECM connectors.

NOTICE:

After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.



b.
A405022

Remove the nut, 2 bolts and ECM.

NOTICE:

If the ECM has been struck or dropped, replace it.



Hide 89667E 6.REMOVE NO. 1 ECM BRACKET

a.
A405023

Remove the 2 screws and No. 1 ECM bracket from the ECM.


Hide 89668 7.REMOVE NO. 2 ECM BRACKET

a.
A405024

Remove the 2 screws and No. 2 ECM bracket from the ECM.