Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System) › 2017.09–2017.12
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0329531 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

for LHD


E367352E05
0.906,1 1.76,1.333 0.854,0.333 10 false from Battery 2.458,1.177 2.781,1.427 0.323,0.25 10 false ALT 4.74,1.521 5.094,1.75 0.354,0.229 10 false TAIL 5.313,1.417 5.667,1.646 0.354,0.229 10 false TAIL 6,0.906 6.427,1.135 0.427,0.229 10 false TRLY 3.875,3.208 5.51,3.708 1.635,0.5 10 false Instrument Panel Junction Block Assembly 5.417,3.76 7.063,4.229 1.646,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 5.417,3.604 5.771,3.833 0.354,0.229 10 false MB 5.771,0.896 6.125,1.125 0.354,0.229 10 false 14 3.5,1.75 3.854,1.979 0.354,0.229 10 false 3C 3.5,1.563 3.854,1.792 0.354,0.229 10 false 32 3.5,2.76 3.854,2.99 0.354,0.229 10 false 3D 3.5,2.563 3.854,2.792 0.354,0.229 10 false 30 1.74,1.74 3.083,2.063 1.344,0.323 10 false to FOG FR Relay* 3.5,1.031 3.854,1.26 0.354,0.229 10 false 3F 3.531,0.844 3.885,1.073 0.354,0.229 10 false 1 0.594,2.729 2.875,3.229 2.281,0.5 10 false to Taillights, Rear Side Marker Lights and License Plate Lights 0.26,4.313 1.833,4.625 1.573,0.313 10 false *: w/ Front Fog Light


for RHD


E367352E06
0.906,1 1.76,1.333 0.854,0.333 10 false from Battery 2.458,1.177 2.781,1.427 0.323,0.25 10 false ALT 4.74,1.521 5.094,1.75 0.354,0.229 10 false TAIL 5.313,1.417 5.667,1.646 0.354,0.229 10 false TAIL 6,0.906 6.427,1.135 0.427,0.229 10 false TRLY 3.875,3.208 5.51,3.708 1.635,0.5 10 false Instrument Panel Junction Block Assembly 5.417,3.76 7.063,4.229 1.646,0.469 10 false Main Body ECU (Multiplex Network Body ECU) 5.417,3.604 5.771,3.833 0.354,0.229 10 false MB 5.771,0.896 6.125,1.125 0.354,0.229 10 false 14 3.5,1.75 3.854,1.979 0.354,0.229 10 false 3C 3.5,1.563 3.854,1.792 0.354,0.229 10 false 32 3.5,2.76 3.854,2.99 0.354,0.229 10 false 3D 3.5,2.563 3.854,2.792 0.354,0.229 10 false 30 1.74,1.74 3.083,2.063 1.344,0.323 10 false to FOG FR Relay* 3.5,1.031 3.854,1.26 0.354,0.229 10 false 3G 3.531,0.844 3.885,1.073 0.354,0.229 10 false 1 0.594,2.729 2.875,3.229 2.281,0.5 10 false to Taillights, Rear Side Marker Lights and License Plate Lights 0.26,4.313 1.833,4.625 1.573,0.313 10 false *: w/ Front Fog Light


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Taillight Relay
50004 123 13
OK:

Taillights illuminate.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3F*1 or 3G*2 instrument panel junction block assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for LHD
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V

for RHD
Tester Connection Condition Specified Condition
3G-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367362C03
1.479,0.344 1.844,0.552 0.365,0.208 4.875,0.729 5.25,0.948 0.375,0.219 2.323,2.042 2.688,2.25 0.365,0.208 4.74,2.052 5.104,2.26 0.365,0.208 5.344,2.063 5.708,2.271 0.365,0.208 4.677,1.542 4.844,1.208 false 0.302,0.177 0.615,0.375 0.313,0.198 10 false *a 1.604,0.385 1.917,0.583 0.313,0.198 10 false 3C 2.427,2.073 2.74,2.271 0.313,0.198 10 false 3D 4.969,0.76 5.281,0.958 0.313,0.198 10 false MB 4.51,1.563 5.01,1.802 0.5,0.24 10 false TRLY 4.865,2.083 5.177,2.281 0.313,0.198 10 false 3F 5.146,2.073 5.458,2.271 0.313,0.198 10 false *A 5.438,2.083 5.75,2.281 0.313,0.198 10 false 3G 5.75,2.083 6.063,2.281 0.313,0.198 10 false *B
*A for LHD *B for RHD
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the battery to terminal 3F-1*1 or 3G-1*2.

*1: for LHD

*2: for RHD



d.

Connect a negative (-) lead from the battery to terminal MB-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-32 - Battery negative (-) terminal* Always 11 to 14 V
3D-30 - Battery negative (-) terminal Always 11 to 14 V


*: w/ Front Fog Light



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY