Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/ Automatic Headlight Beam Level Control System)
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0329531 LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/ Automatic Headlight Beam Level Control System)  Front Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the front fog lights.

WIRING DIAGRAM

for LHD


E381002E01
0.427,0.604 2.115,0.802 1.688,0.198 10 false from Battery 2.021,0.781 3.708,0.979 1.688,0.198 10 false ALT 1.813,2.729 3.5,2.927 1.688,0.198 10 false FOG FR 3.969,2.677 5.969,3.323 2,0.646 10 false Instrument Panel Junction Block Assembly 1.427,3.938 1.927,4.146 0.5,0.208 10 false A57 1.427,4.083 3.115,4.281 1.688,0.198 10 false Fog Light Assembly LH 1.417,5.281 3.104,5.479 1.688,0.198 10 false A56 1.417,5.438 3.104,5.635 1.688,0.198 10 false Fog Light Assembly RH 1.344,3.25 1.844,3.458 0.5,0.208 10 false 1 1.531,3.25 2.031,3.458 0.5,0.208 10 false E 2.594,3.25 3.094,3.458 0.5,0.208 10 false B 2.802,3.25 3.302,3.458 0.5,0.208 10 false 2 1.833,3.604 3.521,3.802 1.688,0.198 10 false Fog Light 2.938,2.833 4.625,3.031 1.688,0.198 10 false FOG FR 2.792,2.104 3.292,2.313 0.5,0.208 10 false 2 2.792,2.438 3.292,2.646 0.5,0.208 10 false 5 3.448,2.104 3.948,2.313 0.5,0.208 10 false 1 3.458,2.438 3.958,2.646 0.5,0.208 10 false 3 3.844,0.417 4.344,0.625 0.5,0.208 10 false 1 3.844,0.625 4.344,0.833 0.5,0.208 10 false 3F 3.823,1.406 4.323,1.615 0.5,0.208 10 false 32 3.823,1.615 4.323,1.823 0.5,0.208 10 false 3C 3.844,2.01 4.344,2.219 0.5,0.208 10 false 25 3.844,2.219 4.344,2.427 0.5,0.208 10 false 3C 5.083,1.781 6.771,1.979 1.688,0.198 10 false TAIL 5.083,1.24 6.771,1.438 1.688,0.198 10 false TAIL 6.063,0.51 6.563,0.719 0.5,0.208 10 false TRLY 6.042,2.094 6.542,2.302 0.5,0.208 10 false FFGO 5.771,0.521 6.271,0.729 0.5,0.208 10 false 14 5.854,2.094 6.354,2.302 0.5,0.208 10 false 7 5.365,4.865 5.865,5.073 0.5,0.208 10 false MB 5.365,5.031 7.01,5.49 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 1.844,4.917 3.531,5.115 1.688,0.198 10 false Fog Light 2.615,4.594 3.115,4.802 0.5,0.208 10 false B 1.531,4.583 2.031,4.792 0.5,0.208 10 false E 1.354,4.583 1.854,4.792 0.5,0.208 10 false 1 2.813,4.594 3.313,4.802 0.5,0.208 10 false 2


for RHD


E381002E02
0.427,0.604 2.115,0.802 1.688,0.198 10 false from Battery 2.021,0.781 3.708,0.979 1.688,0.198 10 false ALT 1.813,2.729 3.5,2.927 1.688,0.198 10 false FOG FR 3.969,2.677 5.969,3.323 2,0.646 10 false Instrument Panel Junction Block Assembly 1.427,3.938 1.927,4.146 0.5,0.208 10 false A57 1.427,4.083 3.115,4.281 1.688,0.198 10 false Fog Light Assembly LH 1.417,5.281 3.104,5.479 1.688,0.198 10 false A56 1.417,5.438 3.104,5.635 1.688,0.198 10 false Fog Light Assembly RH 1.344,3.25 1.844,3.458 0.5,0.208 10 false 1 1.531,3.25 2.031,3.458 0.5,0.208 10 false E 2.594,3.25 3.094,3.458 0.5,0.208 10 false B 2.802,3.25 3.302,3.458 0.5,0.208 10 false 2 1.833,3.604 3.521,3.802 1.688,0.198 10 false Fog Light 2.938,2.833 4.625,3.031 1.688,0.198 10 false FOG FR 2.792,2.104 3.292,2.313 0.5,0.208 10 false 2 2.792,2.438 3.292,2.646 0.5,0.208 10 false 5 3.448,2.104 3.948,2.313 0.5,0.208 10 false 1 3.458,2.438 3.958,2.646 0.5,0.208 10 false 3 3.844,0.417 4.344,0.625 0.5,0.208 10 false 1 3.833,0.625 4.333,0.833 0.5,0.208 10 false 3G 3.823,1.406 4.323,1.615 0.5,0.208 10 false 32 3.823,1.615 4.323,1.823 0.5,0.208 10 false 3C 3.844,2.01 4.344,2.219 0.5,0.208 10 false 25 3.844,2.219 4.344,2.427 0.5,0.208 10 false 3C 5.083,1.781 6.771,1.979 1.688,0.198 10 false TAIL 5.083,1.24 6.771,1.438 1.688,0.198 10 false TAIL 6.063,0.51 6.563,0.719 0.5,0.208 10 false TRLY 6.042,2.094 6.542,2.302 0.5,0.208 10 false FFGO 5.771,0.521 6.271,0.729 0.5,0.208 10 false 14 5.854,2.094 6.354,2.302 0.5,0.208 10 false 7 5.365,4.865 5.865,5.073 0.5,0.208 10 false MB 5.365,5.031 7.01,5.49 1.646,0.458 10 false Main Body ECU (Multiplex Network Body ECU) 1.844,4.917 3.531,5.115 1.688,0.198 10 false Fog Light 2.615,4.594 3.115,4.802 0.5,0.208 10 false B 1.531,4.583 2.031,4.792 0.5,0.208 10 false E 1.354,4.583 1.854,4.792 0.5,0.208 10 false 1 2.802,4.594 3.302,4.802 0.5,0.208 10 false 2


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Front Fog Light Relay Front fog lights OFF or ON Light control switch in tail position
Body Electrical > Main Body > Active Test
Tester Display
Front Fog Light Relay
50004 123 16
OK:

Front fog light relay operates. (Front fog lights come on.)



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - FOG FR RELAY)
3.CHECK HARNESS AND CONNECTOR (POWER SOURCE - FOG FR RELAY)
a.

Remove the FOG FR relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (FOG FR relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FOG FR RELAY INPUT VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FOG FR RELAY INPUT VOLTAGE)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (FOG FR relay) - Body ground Light control switch in tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.INSPECT FOG FR RELAY

NG

9.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
5.INSPECT FOG FR RELAY
a.

Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - FOG LIGHT ASSEMBLY)

NG

REPLACE FOG FR RELAY

6.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - FOG LIGHT ASSEMBLY)
a.

Disconnect the A57 fog light assembly LH connector.


b.

Disconnect the A56 fog light assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (FOG FR relay) - A57-2 (B) Always Below 1 Ω
3 (FOG FR relay) - A56-2 (B) Always Below 1 Ω
3 (FOG FR relay) or A57-2 (B) - Body ground Always 10 kΩ or higher
3 (FOG FR relay) or A56-2 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (FOG FR relay) - 3C-25 Always Below 1 Ω
1 (FOG FR relay) or 3C-25 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367360C06
1.74,0.583 2.115,0.833 0.375,0.25 4.875,0.938 5.25,1.188 0.375,0.25 4.563,2.052 4.146,1.531 false 0.479,0.438 0.792,0.635 0.313,0.198 10 false *a 1.854,0.635 2.167,0.833 0.313,0.198 10 false 3C 4.948,0.979 5.26,1.177 0.313,0.198 10 false MB 4.427,2.073 4.958,2.302 0.531,0.229 10 false FFGO
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-25 - MB-7 (FFGO) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (FOG FR RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FOG FR relay) - 3C-32 Always Below 1 Ω
2 (FOG FR relay) or 3C-32 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR