Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P2120  Throttle / Pedal Position Sensor / Switch "D" Circuit  P2121  Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance  P2122  Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input  P2123  Throttle / Pedal Position Sensor / Switch "D" Circuit High Input  P2125  Throttle / Pedal Position Sensor / Switch "E" Circuit  P2127  Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input  P2128  Throttle / Pedal Position Sensor / Switch "E" Circuit High Input  P2138  Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation  


DESCRIPTION

HINT:

These DTCs relate to the accelerator pedal position sensor.


The accelerator pedal position sensor is built into the accelerator pedal sensor assembly and has 2 sensor circuits: VPA (main) and VPA2 (sub). This sensor is a non-contact type sensor and uses Hall-effect elements in order to yield accurate signals even in extreme driving conditions, such as at high speeds as well as very low speeds. The voltage, which is applied to terminals VPA and VPA2 of the ECM, varies between 0.5 V and 4.75 V in proportion to the operating angle of the accelerator pedal (throttle valve). A signal from VPA indicates the actual accelerator pedal opening angle (throttle valve opening angle) and is used for engine control. A signal from VPA2 conveys the status of the VPA circuit and is used to check the accelerator pedal position sensor itself.

The ECM monitors the actual accelerator pedal opening angle (throttle valve opening angle) through the signals from VPA and VPA2, and controls the throttle actuator according to these signals.

A255815E08
4.333,2.031 4.208,1.948 false 4.323,2.198 4.208,2.146 false 4.344,2.24 4.229,2.333 false 4.344,2.396 4.229,2.51 false 4.344,2.917 4.219,2.917 false 4.354,3.125 4.208,3.125 false 0.844,2.875 0.552,3.281 false 1.063,2.198 1.323,1.365 false 4.333,1.833 3.844,0.938 false 1.323,1.365 1.417,1.365 false 1.063,2.563 0.927,1.823 false 0.927,1.823 0.854,1.823 false 0.552,3.802 1.708,4.135 1.156,0.333 10 Accelerator Pedal Position Sensor 1.458,1.292 1.938,1.469 0.479,0.177 10 Magnet 0.313,1.74 0.844,1.917 0.531,0.177 10 IC No. 1 0.313,3.313 0.844,3.49 0.531,0.177 10 IC No. 2 2.063,1.74 2.531,1.917 0.469,0.177 10 VPA 2.063,2.073 2.552,2.271 0.49,0.198 10 EPA 2.063,2.385 2.583,2.563 0.521,0.177 10 VCPA 2.063,2.688 2.573,2.865 0.51,0.177 10 VPA2 2.063,3 2.563,3.198 0.5,0.198 10 EPA2 2.063,3.323 2.583,3.5 0.521,0.177 10 VCP2 2.677,3.76 3,3.938 0.323,0.177 10 ECM 4.271,1.542 4.427,1.719 0.156,0.177 10 *1 5.865,1.542 6.021,1.719 0.156,0.177 10 *2 3.917,1.854 4.208,2.031 0.292,0.177 10 4.55 3.844,2.063 4.208,2.24 0.365,0.177 10 3.988 3.938,2.281 4.229,2.458 0.292,0.177 10 3.75 3.875,2.469 4.24,2.646 0.365,0.177 10 3.188 3.969,2.823 4.271,3 0.302,0.177 10 1.6 3.979,3.042 4.281,3.219 0.302,0.177 10 0.8 4.406,3.344 4.698,3.521 0.292,0.177 10 0.29 4.26,3.594 4.417,3.771 0.156,0.177 10 0 5.781,3.594 6.073,3.771 0.292,0.177 10 13.1 4.677,3.583 5.604,3.823 0.927,0.24 10 Usable Range 4.667,3.896 7.167,4.094 2.5,0.198 10 Accelerator Pedal Angle (°) 4.344,4.656 6.625,4.833 2.281,0.177 10 *1: Accelerator Pedal Fully Released 4.344,4.969 6.729,5.135 2.385,0.167 10 *2: Accelerator Pedal Fully Depressed 2.156,0.813 3.854,1.167 1.698,0.354 10 Accelerator Pedal Position Sensor Output Voltage (V) 6.479,2.281 6.927,2.51 0.448,0.229 10 VPA 6.438,1.823 6.865,2 0.427,0.177 10 VPA2

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit VPA fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open or short in accelerator pedal sensor assembly circuit

·

ECM


Comes on DTC stored
P2121 Throttle / Pedal Position Sensor / Switch "D" Circuit Range / Performance Either of the following conditions is met (1 trip detection logic):
1.

Difference between VPA and VPA2 is less than 0.4 V, or higher than 1.2 V. (learned value of accelerator off position)

2.

Difference between VPA and VPA2 is greater than or equal to the specified value.


·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored
P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in VCPA circuit

·

Open or ground short in VPA circuit

·

ECM


Comes on DTC stored
P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input VPA is 4.8 V or higher for 2 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in EPA circuit

·

Short in VPA circuit

·

ECM


Comes on DTC stored
P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit VPA2 fluctuates rapidly beyond the upper and lower malfunction thresholds for 0.5 seconds or more (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open or short in accelerator pedal sensor assembly circuit

·

ECM


Comes on DTC stored
P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input VPA2 is 1.2 V or less for 0.5 seconds or more when the accelerator pedal is depressed (1 trip detection logic).
·

Accelerator pedal sensor assembly

·

Open in VCP2 circuit

·

Open or ground short in VPA2 circuit

·

ECM


Comes on DTC stored
P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input Both of the following conditions are met for 2 seconds or more (1 trip detection logic):
(a) VPA2 is 4.8 V or higher.
(b) VPA is between 0.4 V and 3.45 V.
·

Accelerator pedal sensor assembly

·

Open in EPA2 circuit

·

Short in VPA2 circuit

·

ECM


Comes on DTC stored
P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation Either of the following conditions is met for 2 seconds or more (1 trip detection logic):
(a) The difference between VPA and VPA2 is 0.02 V or less.
(b) VPA is 0.4 V or less, and VPA2 is 1.2 V or less.
·

Short between VPA and VPA2 circuits

·

Accelerator pedal sensor assembly

·

ECM


Comes on DTC stored

HINT:

When any of these DTCs are output, check the accelerator pedal position sensor voltage using the GTS. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Trouble Area Accelerator Pedal Fully Released Accelerator Pedal Fully Depressed
Accel Sensor Out No.1 Accel Sensor Out No.2 Accel Sensor Out No.1 Accel Sensor Out No.2
Open in VCP circuit 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V 0 to 0.2 V
Open or ground short in VPA circuit 0 to 0.2 V 1.2 to 2.0 V 0 to 0.2 V 3.4 to 4.75 V
Open or ground short in VPA2 circuit 0.5 to 1.1 V 0 to 0.2 V 2.6 to 4.5 V 0 to 0.2 V
Open in EPA circuit 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V 4.5 to 4.98 V
Normal condition 0.5 to 1.1 V 1.2 to 2.0 V 2.6 to 4.5 V 3.4 to 4.75 V


HINT:

Accelerator pedal positions are expressed as voltages.


MONITOR DESCRIPTION

When either output voltage of VPA or VPA2 deviates from the standard range, or the difference between the output voltages of the 2 sensor circuits is more than the threshold, the ECM determines that there is a malfunction in the accelerator pedal position sensor. The ECM then illuminates the MIL and stores a DTC.

Example:

When the output voltage of VPA is 0.4 V or less for 0.5 seconds or more when the accelerator pedal is fully depressed, DTC P2122 is stored.

MONITOR STRATEGY

Required Sensors/Components Accelerator pedal sensor assembly
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

P2120, P2122, P2123, P2125, P2127, P2128, P2138
A413263E01
2.146,2.448 2.469,2.115 2.469,2.115 2.583,2.104 false 3.719,1.854 2.844,1.177 2.844,1.177 3.073,1.177 false 4.896,2.438 5.208,1.656 5.208,1.656 5.365,1.656 false 0.469,2.354 1.823,2.625 1.354,0.271 10 false Ignition Switch ON 0.073,0.094 1.875,0.438 1.802,0.344 10 false Accelerator Pedal State 0.917,0.417 1.969,0.76 1.052,0.344 10 false Depressed 1,0.906 2.052,1.188 1.052,0.281 10 false Released 2.125,2.51 2.479,2.802 0.354,0.292 10 false [A] 2.979,3.042 3.917,3.375 0.938,0.333 10 false 5 seconds 2.646,2.042 3.531,2.385 0.885,0.344 10 false Released 3.146,1.104 4.521,1.302 1.375,0.198 10 false Depressed 3.896,1.156 4.323,1.49 0.427,0.333 10 false [B] 4.396,3.438 4.792,3.729 0.396,0.292 10 false [C] 5.406,1.583 6.219,1.938 0.813,0.354 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Fully depress and release the accelerator pedal [B].

9.

Check that 5 seconds or more have elapsed since the ignition switch is turned to ON.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P2120, P2122, P2123, P2125, P2127, P2128 or P2138.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.





P2121
A256657E73
3.635,2.01 2.771,1.302 2.771,1.302 2.927,1.302 false 4.729,2.448 5.115,1.802 5.115,1.802 5.26,1.802 false 2.208,2.438 2.438,2.094 2.438,2.094 2.542,2.094 false 0.125,0.094 1.74,0.271 1.615,0.177 10 false Accelerator Pedal State 0.865,0.417 1.583,0.563 0.719,0.146 10 false Depressed 0.948,0.875 1.594,1.031 0.646,0.156 10 false Released 0.51,2.406 1.927,2.573 1.417,0.167 10 false Ignition Switch ON 2.094,2.49 2.469,2.688 0.375,0.198 10 false [A] 4.417,3.438 4.844,3.615 0.427,0.177 10 false [C] 5.365,1.719 6.01,1.875 0.646,0.156 10 false Released 2.375,3.052 3.188,3.229 0.813,0.177 10 false 5 seconds 3.01,1.229 3.729,1.375 0.719,0.146 10 false Depressed 3.865,3.042 4.208,3.24 0.344,0.198 10 false [B] 2.594,2.01 3.24,2.167 0.646,0.156 10 false Released

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Wait for 5 seconds after turning the ignition switch turned to ON.

9.

Operate the accelerator pedal in accordance with the following procedure [B].

(a)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Accel Sens. No.1 Volt %, and Accel Sens. No.2 Volt %.

(b)

Slowly depress the accelerator pedal until Accel Sens. No.1 Volt % is approximately 30% and Accel Sens. No.2 Volt % is approximately 46%, then slowly release the accelerator pedal.


10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P2121.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.





FAIL-SAFE

When these DTCs are stored, the ECM enters fail-safe mode. If either of the 2 sensor circuits malfunctions, the ECM limits the engine output. If both of the circuits malfunction, the ECM regards the accelerator pedal as being released. As a result, the throttle valve is closed and the engine idles.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is turned off.

WIRING DIAGRAM

A413264E01
0.115,3.146 0.51,3.458 0.396,0.313 10 false A20 0.417,3.146 3.302,3.677 2.885,0.531 10 false Accelerator Pedal Position Sensor (Accelerator Pedal Sensor Assembly) 1.583,0.604 2.021,0.875 0.438,0.271 10 false VPA 1.969,0.531 2.125,0.729 0.156,0.198 10 false 6 1.594,1.052 2.052,1.25 0.458,0.198 10 false EPA 1.99,0.948 2.146,1.146 0.156,0.198 10 false 5 1.5,1.458 2.115,1.656 0.615,0.198 10 false VCPA 1.99,1.375 2.146,1.573 0.156,0.198 10 false 4 1.531,1.875 2.146,2.073 0.615,0.198 10 false VPA2 2.021,1.781 2.177,1.979 0.156,0.198 10 false 3 1.531,2.292 2.146,2.49 0.615,0.198 10 false EPA2 2,2.208 2.156,2.406 0.156,0.198 10 false 2 1.521,2.719 2.135,2.917 0.615,0.198 10 false VCP2 2.01,2.583 2.167,2.781 0.156,0.198 10 false 1 5.813,0.875 6.49,1.156 0.677,0.281 10 false 39 kΩ 5.813,2.125 6.375,2.427 0.563,0.302 10 false 39 kΩ 5.313,0.521 5.625,0.719 0.313,0.198 10 false 47 5.604,0.521 6.063,0.719 0.458,0.198 10 false VPA 5.333,0.927 5.646,1.125 0.313,0.198 10 false 48 5.594,1.188 6.052,1.385 0.458,0.198 10 false EPA 6.302,1.26 6.76,1.458 0.458,0.198 10 false 5 V 5.344,1.354 5.656,1.552 0.313,0.198 10 false 49 5.583,1.365 6.198,1.563 0.615,0.198 10 false VCPA 5.365,1.792 5.677,1.99 0.313,0.198 10 false 50 5.594,1.76 6.208,1.958 0.615,0.198 10 false VPA2 5.333,2.188 5.646,2.385 0.313,0.198 10 false 51 5.583,2.417 6.198,2.615 0.615,0.198 10 false EPA2 5.354,2.625 5.667,2.823 0.313,0.198 10 false 52 5.604,2.625 6.219,2.823 0.615,0.198 10 false VCP2 6.302,2.5 6.76,2.698 0.458,0.198 10 false 5 V 5.667,3.156 6.125,3.354 0.458,0.198 10 false A22 6.01,3.167 6.438,3.417 0.427,0.25 10 false ECM

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (ACCEL SENSOR OUT)
A208621C05
0.719,1.75 1,1.969 0.281,0.219 10 *a 2.646,1.74 2.927,1.979 0.281,0.24 10 *b
*a Fully Depressed
*b Fully Released


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Accel Sensor Out No.1 and Accel Sensor Out No.2.

Powertrain > Engine and ECT > Data List
Tester Display
Accel Sensor Out No.1
Accel Sensor Out No.2
50003 234 280,281

e.

Read the value displayed on the GTS.

Standard Voltage:
Accelerator Pedal Operation Accel Sensor Out No.1 Accel Sensor Out No.2 Difference between Accel Sensor Out No.1 and Accel Sensor Out No.2
Fully Released 0.5 to 1.1 V 1.2 to 2.0 V Higher than 0.02 V
Fully Depressed 2.6 to 4.5 V 3.4 to 4.75 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ACCELERATOR PEDAL SENSOR ASSEMBLY)
A372411C17
0.281,0.958 0.667,1.24 0.385,0.281 0.656,1.76 1.177,1.198 true 1.219,1.771 1.385,1.198 true 1.917,1.833 1.771,1.208 true 2.448,1.823 1.958,1.208 true 0.125,0.146 0.438,0.344 0.313,0.198 10 false *a 0.344,1.021 0.802,1.219 0.458,0.198 10 false A20 0.448,1.792 1.063,1.99 0.615,0.198 10 false VCP2 1.01,1.813 1.625,2.01 0.615,0.198 10 false EPA2 1.75,1.885 2.365,2.083 0.615,0.198 10 false VCPA 2.333,1.854 2.792,2.052 0.458,0.198 10 false EPA
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A20-4 (VCPA) - A20-5 (EPA) Ignition switch ON 4.5 to 5.5 V
A20-1 (VCP2) - A20-2 (EPA2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)

NG

5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
3.CHECK HARNESS AND CONNECTOR (RESISTANCE OF ECM)
A372411C14
0.229,1 0.604,1.26 0.375,0.26 1.396,1.833 1.583,1.208 true 0.979,1.823 1.406,1.208 true 2.531,1.802 2.146,1.208 true 2.031,1.813 1.948,1.208 true 0.292,1.052 0.75,1.25 0.458,0.198 10 false A20 1.229,1.865 1.688,2.063 0.458,0.198 10 false VPA2 0.74,1.854 1.198,2.052 0.458,0.198 10 false EPA2 2.458,1.865 2.917,2.063 0.458,0.198 10 false VPA 1.917,1.865 2.375,2.063 0.458,0.198 10 false EPA 0.24,0.208 0.698,0.406 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Accelerator Pedal Sensor Assembly)


a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-6 (VPA) - A20-5 (EPA) Ignition switch off 37.05 to 40.95 kΩ
A20-3 (VPA2) - A20-2 (EPA2) Ignition switch off 37.05 to 40.95 kΩ



Result:
Proceed to
OK
NG



OK

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY

NG

4.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-6 (VPA) - A22-47 (VPA) Always Below 1 Ω
A20-5 (EPA) - A22-48 (EPA) Always Below 1 Ω
A20-3 (VPA2) - A22-50 (VPA2) Always Below 1 Ω
A20-2 (EPA2) - A22-51 (EPA2) Always Below 1 Ω
A20-6 (VPA) or A22-47 (VPA) - Body ground and other terminals Always 10 kΩ or higher
A20-5 (EPA) or A22-48 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A20-3 (VPA2) or A20-50 (VPA2) - Body ground and other terminals Always 10 kΩ or higher
A20-2 (EPA2) or A22-51 (EPA2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL SENSOR ASSEMBLY - ECM)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-4 (VCPA) - A22-49 (VCPA) Always Below 1 Ω
A20-5 (EPA) - A22-48 (EPA) Always Below 1 Ω
A20-1 (VCP2) - A22-52 (VCP2) Always Below 1 Ω
A20-2 (EPA2) - A22-51 (EPA2) Always Below 1 Ω
A20-4 (VCPA) or A22-49 (VCPA) - Body ground and other terminals Always 10 kΩ or higher
A20-5 (EPA) or A22-48 (EPA) - Body ground and other terminals Always 10 kΩ or higher
A20-1 (VCP2) or A22-52 (VCP2) - Body ground and other terminals Always 10 kΩ or higher
A20-2 (EPA2) or A22-51 (EPA2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR