Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P2610  ECM / PCM Internal Engine Off Timer Performance  


MONITOR DESCRIPTION

The soak timer is built into the ECM. While the engine is running, the ECM monitors the synchronization of the soak timer and the CPU clock. If these two are not synchronized, the ECM will interpret this as a malfunction, illuminates the MIL and store this DTC.

A413385E01
0.625,0.969 2.458,1.167 1.833,0.198 10 false from Battery 1.813,1.156 2.615,1.458 0.802,0.302 10 false IG2-MAIN 3.5,1.167 4.688,1.406 1.188,0.24 10 false ECU-IG2 NO. 1 2.719,1.698 3.5,2.021 0.781,0.323 10 false IG2 NO. 1 0.427,1.979 3.75,2.344 3.323,0.365 10 false from Certification ECU (Smart Key ECU Assembly)*1 1.708,2.323 4.188,2.656 2.479,0.333 10 false from Ignition Switch Assembly*2 4.146,0.844 4.76,1.042 0.615,0.198 10 false IGSW 4.979,1.229 5.708,1.635 0.729,0.406 10 false Soak Timer IC 5.031,2.604 5.698,3.063 0.667,0.458 10 false Power Source IC 3.99,2.667 4.688,3 0.698,0.333 10 false +B, +B2 4.948,3.365 5.708,3.844 0.76,0.479 10 false MAIN Relay Control IC 4.198,3.438 4.813,3.635 0.615,0.198 10 false MREL 5.656,4.323 6.115,4.521 0.458,0.198 10 false ECM 2.667,3.927 4.01,4.24 1.344,0.313 10 false EFI-MAIN NO. 1 1.708,3.354 2.813,3.656 1.104,0.302 10 false EFI-MAIN NO. 1 0.635,3.177 1.823,3.479 1.188,0.302 10 false from Battery 0.083,4.073 2.583,4.333 2.5,0.26 10 false *1: w/ Smart Entry and Start System 0.125,4.417 2.625,4.771 2.5,0.354 10 false *2: w/o Smart Entry and Start System

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2610 ECM / PCM Internal Engine Off Timer Performance ECM internal malfunction (2 trip detection logic). ECM Comes on (Euro-OBD) / - (Except Euro-OBD) DTC stored (Euro-OBD) / - (Except Euro-OBD)

MONITOR STRATEGY

Required Sensors/Components ECM
Frequency of Operation Once per driving cycle

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine.

9.

Idle the engine for 10 minutes or more.

10.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

11.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

13.

Input the DTC: P2610.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

DTC P2610 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

2.CLEAR DTC
2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


Result:
Proceed to
NEXT



NEXT

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2610)
a.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


b.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.

Powertrain > Engine and ECT > Trouble Codes
50001 234

c.

If no pending DTCs are output, the repair has been successfully completed.


Result:
Proceed to
NEXT



NEXT

END