Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Injector Circuit  


DESCRIPTION

The fuel injector assembly are located on the intake manifold. They inject fuel into the cylinders based on signals from the ECM.

WIRING DIAGRAM

A413389E01
5.583,0.25 6.042,0.448 0.458,0.198 10 false #10 5.573,1.292 6.031,1.49 0.458,0.198 10 false #20 5.563,2.365 6.021,2.563 0.458,0.198 10 false #30 5.563,3.479 6.021,3.677 0.458,0.198 10 false #40 5.573,4.844 6.031,5.042 0.458,0.198 10 false E01 5.542,5.188 6,5.385 0.458,0.198 10 false E02 5.667,5.875 6.125,6.073 0.458,0.198 10 false C58 6.063,5.906 6.521,6.104 0.458,0.198 10 false ECM 5.333,5.198 5.646,5.396 0.313,0.198 10 false 58 5.333,4.823 5.646,5.021 0.313,0.198 10 false 57 1.729,5.646 4.198,6.063 2.469,0.417 10 false *1: w/ Smart Entry and Start System 1.74,6 4.125,6.521 2.385,0.521 10 false *2: w/o Smart Entry and Start System 5.313,3.458 5.625,3.656 0.313,0.198 10 false 20 3.875,3.448 4.031,3.646 0.156,0.198 10 false 1 4.938,3.469 5.094,3.667 0.156,0.198 10 false 2 4.073,3.688 4.385,3.885 0.313,0.198 10 false #4 4.604,3.688 5.063,3.885 0.458,0.198 10 false #40 3.625,3.896 4.083,4.094 0.458,0.198 10 false C37 3.625,4.094 5.646,4.458 2.021,0.365 10 false No. 4 Fuel Injector Assembly 5.323,2.354 5.635,2.552 0.313,0.198 10 false 19 4.917,2.354 5.073,2.552 0.156,0.198 10 false 2 3.865,2.385 4.021,2.583 0.156,0.198 10 false 1 3.646,2.813 4.104,3.01 0.458,0.198 10 false C36 3.646,3 5.521,3.427 1.875,0.427 10 false No. 3 Fuel Injector Assembly 4.052,2.573 4.365,2.771 0.313,0.198 10 false #3 4.594,2.594 5.052,2.792 0.458,0.198 10 false #30 3.896,1.271 4.052,1.469 0.156,0.198 10 false 1 4.917,1.26 5.073,1.458 0.156,0.198 10 false 2 5.333,1.281 5.646,1.479 0.313,0.198 10 false 18 4.615,1.49 5.073,1.688 0.458,0.198 10 false #20 4.083,1.5 4.396,1.698 0.313,0.198 10 false #2 3.667,1.708 4.125,1.906 0.458,0.198 10 false C35 3.646,1.917 5.479,2.563 1.833,0.646 10 false No. 2 Fuel Injector Assembly 5.344,0.24 5.656,0.438 0.313,0.198 10 false 21 3.885,0.208 4.042,0.406 0.156,0.198 10 false 1 4.906,0.24 5.063,0.438 0.156,0.198 10 false 2 3.656,0.646 4.115,0.844 0.458,0.198 10 false C34 3.667,0.813 5.635,1.115 1.969,0.302 10 false No. 1 Fuel Injector Assembly 4.083,0.438 4.396,0.635 0.313,0.198 10 false #1 4.625,0.448 5.083,0.646 0.458,0.198 10 false #10 2.625,0.542 3.083,0.74 0.458,0.198 10 false INJ 2.135,0.656 2.292,0.854 0.156,0.198 10 false 2 1.313,0.25 1.469,0.448 0.156,0.198 10 false 5 2.146,0.208 2.302,0.406 0.156,0.198 10 false 3 1.344,0.625 1.5,0.823 0.156,0.198 10 false 1 1.479,1.104 2.854,1.302 1.375,0.198 10 false IG2 NO. 1 0.604,0.552 1.542,0.969 0.938,0.417 10 false IG2-MAIN 2.042,2.031 2.656,2.229 0.615,0.198 10 false IG1D 1.813,1.844 2.125,2.042 0.313,0.198 10 false 17 1.813,2.594 2.271,2.792 0.458,0.198 10 false K62 1.823,2.771 3.365,3.25 1.542,0.479 10 false Certification ECU (Smart Key ECU Assembly) 1.448,1.844 1.76,2.042 0.313,0.198 10 false *1 1.333,2.917 1.646,3.115 0.313,0.198 10 false *2 1.979,3.688 2.438,3.885 0.458,0.198 10 false IG1 1.76,3.667 1.917,3.865 0.156,0.198 10 false 8 2.552,3.688 3.01,3.885 0.458,0.198 10 false AM1 2.938,3.688 3.094,3.885 0.156,0.198 10 false 7 1.625,4.125 2.083,4.323 0.458,0.198 10 false K30 1.583,4.333 3.281,4.615 1.698,0.281 10 false Ignition Switch Assembly 3.354,4.01 3.667,4.208 0.313,0.198 10 false *2 2.813,5.042 3.125,5.24 0.313,0.198 10 false *2 3.417,4.385 3.875,4.583 0.458,0.198 10 false AM2 1.917,5.073 2.688,5.271 0.771,0.198 10 false J/B-B 1.073,5.042 1.385,5.24 0.313,0.198 10 false *2 0.448,5.271 1.521,5.469 1.073,0.198 10 false FL MAIN 0.594,5.979 1.667,6.177 1.073,0.198 10 false Battery

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR ASSEMBLY)
A373664C28
0.229,0.719 0.563,0.969 0.333,0.25 0.615,0.708 0.969,0.958 0.354,0.25 0.208,1.042 0.594,1.271 0.385,0.229 0.635,1.031 0.969,1.281 0.333,0.25 0.854,1.448 1.552,1.094 true 0.146,0.115 0.542,0.385 0.396,0.271 10 false *a 0.26,0.74 0.688,0.969 0.427,0.229 10 false C34 0.646,0.74 1.104,0.938 0.458,0.198 10 false C35 0.26,1.083 0.719,1.281 0.458,0.198 10 false C36 0.667,1.073 1.125,1.271 0.458,0.198 10 false C37 0.656,1.479 1.271,1.677 0.615,0.198 10 false #1*b 0.667,1.625 1.281,1.823 0.615,0.198 10 false #2*c 0.667,1.792 1.281,1.99 0.615,0.198 10 false #3*d 0.667,1.958 1.281,2.156 0.615,0.198 10 false #4*e
*a Front view of wire harness connector
(to Fuel Injector Assembly)
*b No. 1 Fuel Injector Assembly
*c No. 2 Fuel Injector Assembly
*d No. 3 Fuel Injector Assembly
*e No. 4 Fuel Injector Assembly


a.

Disconnect the fuel injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C34-1 (#1) - Body ground Ignition switch ON 11 to 14 V
C35-1 (#2) - Body ground Ignition switch ON 11 to 14 V
C36-1 (#3) - Body ground Ignition switch ON 11 to 14 V
C37-1 (#4) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

4.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - FUEL INJECTOR ASSEMBLY)
2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Inspect the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE (FUEL)>FUEL INJECTOR>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>2AR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)

NG

REPLACE FUEL INJECTOR ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
a.

Disconnect the fuel injector assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C34-2 (#10) - C58-21 (#10) Always Below 1 Ω
C35-2 (#20) - C58-18 (#20) Always Below 1 Ω
C36-2 (#30) - C58-19 (#30) Always Below 1 Ω
C37-2 (#40) - C58-20 (#40) Always Below 1 Ω
C34-2 (#10) or C58-21 (#10) - Body ground and other terminals Always 10 kΩ or higher
C35-2 (#20) or C58-18 (#20) - Body ground and other terminals Always 10 kΩ or higher
C36-2 (#30) or C58-19 (#30) - Body ground and other terminals Always 10 kΩ or higher
C37-2 (#40) or C58-20 (#40) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - FUEL INJECTOR ASSEMBLY)
a.

Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel injector assembly connector.


c.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG2 NO. 1 relay) - C34-1 (#1) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C35-1 (#2) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C36-1 (#3) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C37-1 (#4) Always Below 1 Ω
3 (IG2 NO. 1 relay) or C34-1 (#1) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C35-1 (#2) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C36-1 (#3) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C37-1 (#4) - Body ground and other terminals Always 10 kΩ or higher


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR