Home › Engine / Hybrid System › 2AR-FE (ENGINE CONTROL) › SFI SYSTEM › 2017.09–2021.02
RM33A0E _51 Engine / Hybrid System _065323 2AR-FE ENGINE CONTROL _0329559 SFI SYSTEM C

2AR-FE ENGINE CONTROL  SFI SYSTEM  P0617  Starter Relay Circuit High  


MONITOR DESCRIPTION

While the engine is being cranked, positive battery voltage is applied to terminal STA of the ECM.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores this DTC.

This monitor runs when the vehicle is driven at 20 km/h (12.43 mph) or more for 20 seconds or more.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0617 Starter Relay Circuit High All of the following conditions are met, and a (+B) battery voltage of 10.5 V or higher is applied to the ECM for 20 seconds (1 trip detection logic):

(a) The vehicle speed is 20 km/h (12.43 mph) or more.

(b) The engine speed is 1000 rpm or higher.

(c) The STA signal is on.


·

ST relay

·

Park/neutral position switch assembly

·

STA signal circuit

·

ECM


Comes on DTC stored

MONITOR STRATEGY

Required Sensors/Components (Main) ST relay
Park/Neutral position switch assembly
Certification ECU (smart key ECU assembly)
Required Sensors/Components (Related) Vehicle speed sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Vehicle speed 20 km/h (12.43 mph) or more
Engine speed 1000 rpm or higher

TYPICAL MALFUNCTION THRESHOLDS

Starter signal On

CONFIRMATION DRIVING PATTERN

A231469E88
1.229,1.948 1.604,2.125 0.375,0.177 10 false Idling 0.51,2.26 1.688,2.635 1.177,0.375 10 false Ignition Switch ON 1.052,0.813 1.646,1.042 0.594,0.229 10 false 24 km/h 2.396,2.854 3.083,3.167 0.688,0.313 10 false 5 seconds or more 3.594,2.938 4.865,3.104 1.271,0.167 10 false 20 seconds or more 2,2.333 2.406,2.521 0.406,0.188 10 false [A] 2.583,2.125 2.792,2.302 0.208,0.177 10 false [B] 4.031,0.458 4.26,0.625 0.229,0.167 10 false [C] 4.906,3.344 5.135,3.51 0.229,0.167 10 false [D]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on [A].

8.

Start the engine.

9.

Idle the engine for 5 seconds or more [B].

10.

Drive the vehicle at 24 km/h (15 mph) or more for 20 seconds or more [C].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

14.

Input the DTC: P0617.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [C] and [D] again and, if necessary, extend the driving time.




WIRING DIAGRAM

A402124E05
5.781,0.875 6.24,1.073 0.458,0.198 10 false NEO 6.021,5.302 6.479,5.5 0.458,0.198 10 false A22 6.333,5.302 6.792,5.5 0.458,0.198 10 false ECM 5.792,1.344 6.25,1.542 0.458,0.198 10 false NSW 5.521,0.74 5.979,0.938 0.458,0.198 10 false 16 5.521,1.198 5.979,1.396 0.458,0.198 10 false 23 5.802,4.01 6.26,4.208 0.458,0.198 10 false STA 5.51,4.01 5.969,4.208 0.458,0.198 10 false 29 2.979,4.802 3.438,5 0.458,0.198 10 false ST 2.698,4.354 3.156,4.552 0.458,0.198 10 false 2 2.698,5.281 3.156,5.479 0.458,0.198 10 false 1 2.229,4.354 2.688,4.552 0.458,0.198 10 false 5 2.219,5.281 2.677,5.479 0.458,0.198 10 false 3 0.427,4.396 1.271,4.698 0.844,0.302 10 false ST NO. 1 0.427,5.24 1.271,5.542 0.844,0.302 10 false FL MAIN 0.594,6.844 1.438,7.146 0.844,0.302 10 false Battery 1.052,6.104 1.896,6.406 0.844,0.302 10 false C74 1.125,5.906 1.969,6.208 0.844,0.302 10 false 1 1.76,5.729 2.604,6.031 0.844,0.302 10 false C61 2.083,5.729 2.927,6.031 0.844,0.302 10 false 1 2.948,2.75 3.406,2.948 0.458,0.198 10 false C55 2.948,2.917 5.75,3.219 2.802,0.302 10 false Park/Neutral Position Switch Assembly 1.323,0.875 1.781,1.073 0.458,0.198 10 false NE 1.625,0.729 2.083,0.927 0.458,0.198 10 false 16 0.219,0.188 4.375,0.594 4.156,0.406 12 false w/ Smart Entry and Start System: 1.146,1.323 1.604,1.521 0.458,0.198 10 false STAR 1.646,1.198 2.104,1.396 0.458,0.198 10 false 9 1.24,1.719 1.698,1.917 0.458,0.198 10 false STA 1.625,1.594 2.083,1.792 0.458,0.198 10 false 20 0.104,2.292 1.969,2.677 1.865,0.385 10 false Certification ECU (Smart Key ECU Assembly) 0.115,2.125 0.573,2.323 0.458,0.198 10 false A13 3.698,2.344 4.156,2.542 0.458,0.198 10 false L 4.219,2.344 4.677,2.542 0.458,0.198 10 false B 4.406,2.344 4.865,2.542 0.458,0.198 10 false 4 3.521,2.344 3.979,2.542 0.458,0.198 10 false 9 1.135,6.906 2.281,7.313 1.146,0.406 10 false Starter Assembly

A402125E02
5.719,1.073 6.177,1.271 0.458,0.198 10 false NSW 5.427,0.948 5.885,1.146 0.458,0.198 10 false 23 5.698,3.417 6.156,3.615 0.458,0.198 10 false STA 5.417,3.406 5.875,3.604 0.458,0.198 10 false 29 6.198,4.729 6.656,4.927 0.458,0.198 10 false ECM 2.104,0.927 2.563,1.125 0.458,0.198 10 false ST1 1.531,0.927 1.99,1.125 0.458,0.198 10 false AM1 2.479,0.938 2.938,1.135 0.458,0.198 10 false 5 1.313,0.948 1.771,1.146 0.458,0.198 10 false 7 1.49,1.563 2.438,2.01 0.948,0.448 10 false Ignition Switch Assembly 1.49,1.406 2.438,1.854 0.948,0.448 10 false K30 0.594,1.885 1.542,2.333 0.948,0.448 10 false AM2 0.594,2.771 1.542,3.219 0.948,0.448 10 false J/B-B 1.333,3.719 2.052,4.094 0.719,0.375 10 false ST NO. 1 0.604,4.615 1.323,4.99 0.719,0.375 10 false FL MAIN 0.771,6.604 1.49,6.979 0.719,0.375 10 false Battery 1.313,6.552 2.01,7.01 0.698,0.458 10 false Starter Assembly 1.083,5.698 1.802,6.073 0.719,0.375 10 false C74 1.115,5.5 1.833,5.875 0.719,0.375 10 false 1 1.75,5.292 2.469,5.667 0.719,0.375 10 false C61 2.083,5.26 2.802,5.635 0.719,0.375 10 false 1 2.531,4.854 3.25,5.229 0.719,0.375 10 false 3 2.542,3.896 3.26,4.271 0.719,0.375 10 false 5 3.052,3.896 3.771,4.271 0.719,0.375 10 false 2 3.052,4.865 3.771,5.24 0.719,0.375 10 false 1 3.313,4.354 4.031,4.729 0.719,0.375 10 false ST 3.396,2.604 5.198,3.052 1.802,0.448 10 false Park/Neutral Position Switch Assembly 3.396,2.438 3.875,2.74 0.479,0.302 10 false C55 4.365,2.021 4.844,2.323 0.479,0.302 10 false B 4.583,2.01 5.063,2.313 0.479,0.302 10 false 4 3.5,2.01 3.979,2.313 0.479,0.302 10 false 9 3.719,2.01 4.198,2.313 0.479,0.302 10 false L 5.885,4.729 6.344,4.927 0.458,0.198 10 false A22 0.219,0.208 3.073,0.656 2.854,0.448 12 false w/o Smart Entry and Start System:

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

According to the display on the GTS, read the Data List.

Standard:
Condition Starter Signal
Ignition switch ON OFF



f.

According to the display on the GTS, read the Data List while the vehicle is being driven with an engine speed of 1000 rpm or more at a vehicle speed of 20 km/h (12.43 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


Standard:
Condition Starter Signal
Driving at 20 km/h (12.43 mph) or more (engine speed 1000 rpm or more) OFF



HINT:

If the result of either of the above is not as specified, proceed to the next step with the ignition switch to ON, GTS connected and Data List item "Starter Signal" selected.


Result:
Result Proceed to
OK A
NG (w/ Smart Entry and Start System) B
NG (w/o Smart Entry and Start System) C


HINT:

If the starter assembly operates continuously when the ignition switch is turned to ON, proceed to the next step without reading the Data List item "Starter Signal".



A

B

2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)

C

7.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
2.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter Signal" does not change from ON A
The Data List item "Starter Signal" changes from ON to OFF B


HINT:
·

When the result of the above inspection is "The Data List item "Starter Signal" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

B

REPLACE ST RELAY

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A402442C01
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


HINT:

The purpose of this step is to check for ST relay terminal voltage under abnormal conditions.


a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
4.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A402442C02
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


a.

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

5.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A402442C03
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY - ST RELAY)

B

6.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - SMART KEY ECU ASSEMBLY - ST RELAY)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the certification ECU (smart key ECU assembly) connector.


d.

Remove the ST relay from the engine room relay block and junction block assembly.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-29 (STA), C55-9 (L), A13-20 (STA) or 2 (ST relay) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK SMART ENTRY AND START SYSTEM (CHECK FOR STA TERMINAL VOLTAGE OF SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT ST RELAY (CHECK FOR SHORT CIRCUIT)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

According to the display on the GTS, read the Data List.

Result:
Result Proceed to
The Data List item "Starter Signal" does not change from ON. A
The Data List item "Starter Signal" changes from ON to OFF. B


HINT:
·

When the result of the above inspection is "The Data List item "Starter Signal" does not change from ON", the ST relay is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)

B

REPLACE ST RELAY

8.CHECK TERMINAL VOLTAGE (POWER SOURCE OF ST RELAY)
A402442C01
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


HINT:

The purpose of this step is to check for ST relay terminal voltage under abnormal conditions.


a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Turn the ignition switch to ON.


c.

Measure the voltage between ST relay terminal 2 and body ground.

HINT:
·

Make a note of the measured voltage as it will be necessary for the inspecting the change in voltage in the next step. As the next step should be conducted under the same conditions, keep the ignition switch ON and do not install the ST relay.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.

·

If any voltage was measured with the ignition switch ON, one of the following malfunctions is suspected:

-

Short to +B in the circuit of a connected ECU or the switch.

-

Short to +B in the wire harness.





Result:
Proceed to
NEXT



NEXT

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY (CHECK FOR SHORT CIRCUIT)
A402442C02
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


a.

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the park/neutral position switch assembly is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

10.INSPECT ECM (CHECK FOR SHORT CIRCUIT)

B

10.INSPECT ECM (CHECK FOR SHORT CIRCUIT)
A402442C03
1.542,0.073 1.854,0.271 0.313,0.198 10 false *1 0.292,0.708 0.604,0.99 0.313,0.281 10 false *2
*1 Engine Room Relay Block and Junction Block Assembly
*2 ST Relay


a.

Disconnect the ECM connector.


b.

Measure the voltage between ST relay terminal 2 and body ground and compare it to the voltage measured in the previous step.

Result:
Result Proceed to
The voltage between ST relay terminal 2 and body ground does not change when the connector is disconnected. A
The voltage between ST relay terminal 2 and body ground changes when the connector is disconnected. B


HINT:
·

If the voltage is the same before and after disconnecting the connector, the ECM is normal.

·

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.





A

REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

B