Home › Engine / Hybrid System › 2GR-FKS (ENGINE CONTROL) › SFI SYSTEM
RM33A0E _51 Engine / Hybrid System _065332 2GR-FKS ENGINE CONTROL _0329835 SFI SYSTEM C

2GR-FKS ENGINE CONTROL  SFI SYSTEM  P034011  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground  P034015  Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open  P034511  Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground  P034515  Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open  


DESCRIPTION

The VVT sensor (for intake camshaft) (VV1, VV2 signal) consists of a magnet and MRE (Magneto Resistance Element).

The intake camshaft has a timing rotor for the VVT sensor. When the intake camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration, injection timing and the Variable Valve Timing (VVT) system.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P034011 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Ground The VVT sensor (for intake camshaft of bank 1) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on DTC stored SAE Code: P0342
P034015 Camshaft Position Sensor "A" Bank 1 or Single Sensor Circuit Short to Battery or Open The VVT sensor (for intake camshaft of bank 1) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 1) circuit

·

VVT sensor (for intake camshaft of bank 1)

·

ECM


Comes on DTC stored SAE Code: P0343
P034511 Camshaft Position Sensor "A" Bank 2 Circuit Short to Ground The VVT sensor (for intake camshaft of bank 2) output voltage is less than 0.3 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on DTC stored SAE Code: P0347
P034515 Camshaft Position Sensor "A" Bank 2 Circuit Short to Battery or Open The VVT sensor (for intake camshaft of bank 2) output voltage is higher than 4.7 V for 4 seconds or more (1 trip detection logic).
·

Open or short in VVT sensor (for intake camshaft of bank 2) circuit

·

VVT sensor (for intake camshaft of bank 2)

·

ECM


Comes on DTC stored SAE Code: P0348

A356009E10
0.094,1.323 0.479,1.542 0.385,0.219 10 false CH1 0.135,2.063 0.469,2.271 0.333,0.208 10 false CH2 2.813,1.479 3.271,1.677 0.458,0.198 10 false GND 2.802,2.208 3.26,2.406 0.458,0.198 10 false GND 2.677,0.771 3.302,1 0.625,0.229 10 false 5 V/DIV. 1.25,2.552 2.938,2.75 1.688,0.198 10 false 20 ms./DIV.

Reference: Inspection using an oscilloscope.

HINT:
·

The correct waveform is as shown.

·

VV1 stands for the VVT sensor (for intake camshaft of bank 1) signal, and VV2 stands for the VVT sensor (for intake camshaft of bank 2) signal.



ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between VV2+ and VV2-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If the output voltage transmitted by the VVT sensor (for intake camshaft) remains low or high the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction in the sensor circuit illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) VVT sensor (for intake camshaft)
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG).

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the engine switch off and wait for at least 30 seconds.

6.

Turn the engine switch on (IG).

7.

Turn the GTS on.

8.

Wait for 5 seconds or more.

9.

Enter the following menus: Powertrain / Engine / Trouble Codes.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P034011, P034015, P034511 or P034515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system is malfunctioning.




WIRING DIAGRAM

A357733E15
1.917,0.802 2.229,1 0.313,0.198 10 false VC 2.198,0.813 2.354,1.01 0.156,0.198 10 false 3 1.75,1.365 2.365,1.563 0.615,0.198 10 false VVR+ 2.188,1.354 2.344,1.552 0.156,0.198 10 false 1 1.771,1.885 2.385,2.083 0.615,0.198 10 false VVR- 2.198,1.885 2.354,2.083 0.156,0.198 10 false 2 0.969,2.365 1.427,2.563 0.458,0.198 10 false C16 0.969,2.542 3.781,2.833 2.813,0.292 10 false VVT Sensor (for Intake Camshaft of Bank 1) 4.771,0.813 5.083,1.01 0.313,0.198 10 false 99 4.698,1.333 5.156,1.531 0.458,0.198 10 false 132 4.708,1.896 5.167,2.094 0.458,0.198 10 false 100 5.01,0.813 5.625,1.01 0.615,0.198 10 false VCV1 5.01,1.333 5.625,1.531 0.615,0.198 10 false VV1+ 5.021,1.885 5.635,2.083 0.615,0.198 10 false VV1- 5.469,5.156 5.813,5.385 0.344,0.229 10 false C96 5.854,5.156 6.313,5.354 0.458,0.198 10 false ECM 1.906,3.25 2.219,3.448 0.313,0.198 10 false VC 2.188,3.25 2.344,3.448 0.156,0.198 10 false 3 1.771,3.771 2.385,3.969 0.615,0.198 10 false VVL+ 2.188,3.771 2.344,3.969 0.156,0.198 10 false 1 1.792,4.281 2.219,4.5 0.427,0.219 10 false VVL- 2.198,4.292 2.354,4.49 0.156,0.198 10 false 2 0.979,4.823 1.438,5.021 0.458,0.198 10 false C19 0.979,5.021 3.708,5.396 2.729,0.375 10 false VVT Sensor (for Intake Camshaft of Bank 2) 4.781,3.24 5.094,3.438 0.313,0.198 10 false 98 4.708,3.771 5.167,3.969 0.458,0.198 10 false 129 4.792,4.302 5.104,4.5 0.313,0.198 10 false 97 5.01,3.24 5.625,3.438 0.615,0.198 10 false VCV2 5.021,3.771 5.635,3.969 0.615,0.198 10 false VV2+ 5.031,4.302 5.646,4.5 0.615,0.198 10 false VV2- 5.99,0.635 6.604,0.833 0.615,0.198 10 false 5 V 6,3.052 6.615,3.25 0.615,0.198 10 false 5 V 5.917,1.198 6.531,1.396 0.615,0.198 10 false 1.5 kΩ 5.917,3.615 6.531,3.813 0.615,0.198 10 false 1.5 kΩ

CAUTION / NOTICE / HINT

HINT:
·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR
A376492C68
0.198,1.156 0.552,1.406 0.354,0.25 0.198,0.813 0.552,1.063 0.354,0.25 1.958,1.167 2.448,1.76 true 1.385,1.177 0.75,1.615 true 1.615,1.177 1.552,1.844 true 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.26,1.198 0.573,1.396 0.313,0.198 10 false C19 2.396,1.771 2.708,1.969 0.313,0.198 10 false VC 0.25,0.854 0.563,1.052 0.313,0.198 10 false C16 0.583,0.823 0.896,1.021 0.313,0.198 10 false *b 0.583,1.167 0.896,1.365 0.313,0.198 10 false *c 0.479,1.635 1.031,1.865 0.552,0.229 10 false VVR+*b 0.479,1.813 1.031,2.042 0.552,0.229 10 false VVL+*c 1.333,1.844 1.885,2.073 0.552,0.229 10 false VVR-*b 1.354,2 1.917,2.177 0.563,0.177 10 false VVL-*c
*a Front view of wire harness connector
(to VVT Sensor (for Intake Camshaft))
*b Bank 1
*c Bank 2


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C16-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C19-3 (VC) - Body ground Engine switch on (IG) 4.5 to 5.5 V
C16-1 (VVR+) - Body ground Engine switch on (IG) 3.0 to 5.0 V
C19-1 (VVL+) - Body ground Engine switch on (IG) 3.0 to 5.0 V



d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-3 (VC) - C16-1 (VVR+) Engine switch off 1.425 to 1.575 kΩ
C19-3 (VC) - C19-1 (VVL+) Engine switch off 1.425 to 1.575 kΩ
C16-2 (VVR-) - Body ground Always Below 1 Ω
C19-2 (VVL-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

NG

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
2.CHECK HARNESS AND CONNECTOR (VVT SENSOR (FOR INTAKE CAMSHAFT) - ECM)
a.

Disconnect the VVT sensor (for intake camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C16-1 (VVR+) - C96-132 (VV1+) Always Below 1 Ω
C16-2 (VVR-) - C96-100 (VV1-) Always Below 1 Ω
C16-3 (VC) - C96-99 (VCV1) Always Below 1 Ω
C19-1 (VVL+) - C96-129 (VV2+) Always Below 1 Ω
C19-2 (VVL-) - C96-97 (VV2-) Always Below 1 Ω
C19-3 (VC) - C96-98 (VCV2) Always Below 1 Ω
C16-1 (VVR+) or C96-132 (VV1+) - Body ground and other terminals Always 10 kΩ or higher
C16-2 (VVR-) or C96-100 (VV1-) - Body ground and other terminals Always 10 kΩ or higher
C16-3 (VC) or C96-99 (VCV1) - Body ground and other terminals Always 10 kΩ or higher
C19-1 (VVL+) or C96-129 (VV2+) - Body ground and other terminals Always 10 kΩ or higher
C19-2 (VVL-) or C96-97 (VV2-) - Body ground and other terminals Always 10 kΩ or higher
C19-3 (VC) or C96-98 (VCV2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR