Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory) › 2017.09–2018.04
RM33A0E _58 Vehicle Interior _065385 SEAT _0328606 FRONT POWER SEAT CONTROL SYSTEM(w/ Memory) C

SEAT  FRONT POWER SEAT CONTROL SYSTEM(w/ Memory)  B2653  Lifter Sensor Malfunction  


DESCRIPTION

When the position control ECU assembly (driver seat) does not receive a lifter motor position sensor signal despite the seat having been moved upward or downward by power seat motor operation, this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B2653 Lifter Sensor Malfunction Lifter motor position sensor signal not received when power seat moved upward or downward
·

Position control ECU assembly (driver seat)

·

Power seat lifter motor assembly (driver seat)

·

Wire harness or connector



WIRING DIAGRAM

B493362E02
2.198,0.438 2.604,0.667 0.406,0.229 10 false 1 2.208,0.969 2.615,1.198 0.406,0.229 10 false 4 2.208,1.458 2.615,1.688 0.406,0.229 10 false 2 2.208,1.979 2.615,2.208 0.406,0.229 10 false 3 0.76,2.385 1.167,2.615 0.406,0.229 10 false a7 0.75,2.563 2.927,2.99 2.177,0.427 10 false Power Seat Lifter Motor Assembly (Driver Seat) 0.458,3.333 3.323,3.604 2.865,0.271 10 false Front Seat Adjuster Assembly (Driver Seat) 4.75,2.594 6.698,3.115 1.948,0.521 10 false Position Control ECU Assembly (Driver Seat) 5.219,2.094 5.76,2.313 0.542,0.219 10 false SENG 5.25,1.573 5.802,1.823 0.552,0.25 10 false SSRL 5.229,0.552 5.719,0.781 0.49,0.229 10 false LFT+ 4.802,0.531 5.208,0.76 0.406,0.229 10 false a10 4.813,1.052 5.219,1.281 0.406,0.229 10 false a11 4.844,0.302 5.25,0.531 0.406,0.229 10 false 6 4.865,0.823 5.271,1.052 0.406,0.229 10 false 5 4.823,1.333 5.229,1.563 0.406,0.229 10 false 25 4.823,1.844 5.229,2.073 0.406,0.229 10 false 12 4.813,1.563 5.219,1.792 0.406,0.229 10 false a12 4.802,2.094 5.208,2.323 0.406,0.229 10 false a12 5.24,1.083 5.729,1.313 0.49,0.229 10 false LFT-

PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Body Electrical > Driver Seat > Clear DTCs
50002 162

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Body Electrical > Driver Seat > Trouble Codes
50001 162
OK:

DTC B2653 is not output.



Result:
Proceed to
OK
NG



OK

NG

3.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
3.PERFORM ACTIVE TEST USING GTS (SEAT LIFTER OPERATION)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Driver Seat / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Driver Seat > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Lifter Operation Seat lifter operation OFF/Down/Up -
Body Electrical > Driver Seat > Active Test
Tester Display
Lifter Operation
50004 162 2
OK:

Lifter motor operates normally.



Result:
Proceed to
OK
NG



OK

4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)

NG

7.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
4.CHECK POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) (LIFTER MOTOR CIRCUIT)
a.

Disconnect the a7 power seat lifter motor assembly (driver seat) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a7-2 - a7-3 Lifter switch on 4.8 to 5.1 V



Result:
Proceed to
OK
NG



OK

5.CHECK POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

NG

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
5.CHECK POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.
B343020C52
1.5,0.167 1.917,0.417 0.417,0.25 0.156,0.146 0.396,0.396 0.24,0.25 10 false *a 1.625,0.208 2,0.479 0.375,0.271 10 false a7
*a Component with harness connected
(Power Seat Lifter Motor Assembly (Driver Seat))


Reconnect the a7 power seat lifter motor assembly (driver seat) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
a7-2 - Body ground Lifter motor operating 4.5 to 4.8 V



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

6.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the a12 position control ECU assembly (driver seat) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a12-25 (SSRL) - a7-2 Always Below 1 Ω
a12-25 (SSRL) or a7-2 - Body ground Always 10 kΩ or higher
a12-12 (SENG) - a7-3 Always Below 1 Ω
a12-12 (SENG) or a7-3 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)
a.

Remove the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>DISASSEMBLY


b.

Inspect the power seat lifter motor assembly (driver seat).

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))

NG

REPLACE POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT)

8.CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT) - POWER SEAT LIFTER MOTOR ASSEMBLY (DRIVER SEAT))
a.

Disconnect the a10 and a11 position control ECU assembly (driver seat) connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
a10-6 (LFT+) - a7-1 Always Below 1 Ω
a10-6 (LFT+) or a7-1 - Body ground Always 10 kΩ or higher
a11-5 (LFT-) - a7-4 Always Below 1 Ω
a11-5 (LFT-) or a7-4 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POSITION CONTROL ECU ASSEMBLY (DRIVER SEAT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR