Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM33A0E _59 Vehicle Exterior _065390 WINDOW / GLASS _0330292 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  All Power Windows do not Operate with Driver Side Door Key Cylinder or Wireless Transmitter  


DESCRIPTION

Wireless Transmitter-linked Function (w/o Canister Pump Module)
·

w/ Smart Entry and Start System:

When a key switch is pushed: 1) the door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU) through the certification ECU (smart key ECU assembly); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assemblies; and 4) the power window regulator motor assemblies are activated.

·

w/o Smart Entry and Start System:

When a key switch is pushed: 1) the door control receiver receives the wireless door lock signal; 2) the door control receiver sends a signal to the main body ECU (multiplex network body ECU); 3) the main body ECU (multiplex network body ECU) sends the operation permission signal to the power window regulator motor assemblies; and 4) the power window regulator motor assemblies are activated.


Key-linked Function

When the driver door key cylinder (key linked switch) is turned and held: 1) the door lock motor receives the signal; 2) the main body ECU (multiplex network body ECU) sends the signal to the power window regulator motor assemblies; and 3) the power window regulator motor assemblies are activated.


CAUTION / NOTICE / HINT

NOTICE:
·

These functions are set through customize settings, as they are off by default.

·

The power window control system uses the LIN communication system and CAN communication system. Inspect the communication functions by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication systems are functioning properly.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System


·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

*: w/ Door Control Battery




PROCEDURE

1.CHECK BASIC FUNCTION (WIRELESS AND POWER DOOR LOCK CONTROL SYSTEM)
a.

Check that the wireless door lock / unlock function operates normally.

w/ Smart Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/ Smart Entry and Start System)>OPERATION CHECK

w/o Smart Entry and Start System: Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Smart Entry and Start System)>OPERATION CHECK


b.

Check that the key-linked lock/unlock function operates normally.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock function and key-linked lock/unlock function operate normally A
Wireless door lock/unlock function does not operate normally B
Key-linked lock/unlock function does not operate normally C



A

2.CHECK MANUAL UP / DOWN FUNCTION

B

GO TO WIRELESS DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

C

GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Problem Symptoms Table)

2.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the manual up and down functions using the multiplex network master switch assembly, power window regulator switch assembly and rear power window regulator switch assemblies can operate all of the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Manual up and down functions are normal.



Result:
Proceed to
OK
NG



OK

3.CHECK REMOTE UP / DOWN FUNCTION

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)

3.CHECK REMOTE UP / DOWN FUNCTION
a.

Check that the remote up and down functions using the multiplex network master switch assembly can operate all of the power windows.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>OPERATION CHECK

OK:

Remote up and down functions are normal.



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

GO TO OTHER PROBLEM (Proceed to Problem Symptoms Table)