When it is determined that the vehicle is being driven in a straight line or on a gradual curve based on signals from the yaw rate and acceleration sensor, the millimeter wave radar sensor assembly performs self-diagnosis to check if the sensor beam axis has deviated. When the millimeter wave radar sensor assembly beam axis is misaligned, the millimeter wave radar sensor assembly stores DTC C1A11.
After installing a new millimeter wave radar sensor assembly, if sensor beam axis adjustment is not performed, DTC C1A14 is stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1A11 | Front Radar Sensor Incorrect Axial Gap | When the vehicle is being driven at a speed of 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, misalignment of the millimeter wave radar sensor assembly is detected for approximately 0.3 seconds or more. | Millimeter wave radar sensor assembly |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted | When the vehicle is being driven at a speed of 5 km/h (3 mph) or more and the dynamic radar cruise control system is operating, incompletion of the millimeter wave radar sensor assembly beam axis alignment is detected for approximately 0.3 seconds or more. | Millimeter wave radar sensor assembly |
When replacing the millimeter wave radar sensor assembly, make sure to replace it with a new one. If a device which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle, and as a result, a DTC may be stored.
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
If only history DTCs are stored, they may have been stored due to a temporary condition such as overloading of the vehicle.
If only history DTCs are stored, they may have been stored due to a temporary condition such as overloading of the vehicle.
Check if the stored DTCs are current DTCs.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Enter the following menus: Body Electrical / Radar Cruise 2 / Trouble Codes.
Check for DTCs.
| Result | Proceed to |
|---|---|
| Current DTC C1A11 is output | A |
| Current DTC C1A14 is output | B |
| History DTC C1A11 is output | C |
A
B
C
Check the operating conditions of the vehicle.
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is temporarily misaligned due to the vehicle being overloaded.
| Result | Proceed to |
|---|---|
| Vehicle is not overloaded or being towed | A |
| Vehicle is overloaded or being towed | B |
A
B
Check the front and rear wheel alignment (toe).
for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
DTC C1A11 may be stored if the millimeter wave radar sensor assembly beam axis is misaligned due to incorrect wheel alignment (toe).
| Result | Proceed to |
|---|---|
| Front or rear wheel is misaligned (toe) | A |
| Front and rear wheels are not misaligned (toe) | B |
A
B
Adjust the alignment (toe) of the wheels.
for front wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>FRONT WHEEL ALIGNMENT>ADJUSTMENT
for rear wheel alignment: Click hereSuspension>ALIGNMENT / HANDLING DIAGNOSIS>REAR WHEEL ALIGNMENT>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the engine switch on (IG).
Turn the dynamic radar cruise control system on using the cruise control main switch.
Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A11 is not output | A |
| DTC C1A11 is output | B |
A
B
Check that the bracket of the millimeter wave radar sensor assembly is not deformed.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>INSTALLATION
If the bracket is deformed, replace the millimeter wave radar sensor assembly.
| Result | Proceed to |
|---|---|
| Bracket is not deformed | A |
| Bracket is deformed | B |
A
B
Replace the millimeter wave radar sensor assembly.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Return the vehicle to normal operating conditions.
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Perform millimeter wave radar sensor assembly adjustment.
Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Perform the following procedure.
If the following procedure is not performed, the previously output DTC cannot be detected.
Turn the engine switch on (IG).
Turn the dynamic radar cruise control system on using the cruise control main switch.
Drive the vehicle at 5 km/h (3 mph) or more for 1 second or more.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC C1A14 is not output | A |
| DTC C1A14 is output | B |
A
B
Check for DTCs related to misalignment of millimeter wave radar sensor assembly.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT