Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL PUMP (w/o Canister Pump Module) › from 2017.12
RM33A0E _51 Engine / Hybrid System _065343 A25A-FKS FUEL _0341521 FUEL PUMP(w/o Canister Pump Module) A

A25A-FKS FUEL  FUEL PUMP(w/o Canister Pump Module)  REASSEMBLY  


PROCEDURE

Hide 23221 1.INSTALL FUEL PUMP

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>INITIALIZATION


a.

for Type A:

i.
A345414C04
2.323,0.583 2.375,0.427 2.375,0.427 2.531,0.427 false 2.323,0.771 2.677,0.771 false 2.583,0.344 2.896,0.5 0.313,0.156 10 false *1 2.74,0.698 3.052,0.854 0.313,0.156 10 false *2
*1 O-ring
*2 Fuel Pump Spacer


Apply gasoline to a new O-ring. Then install the O-ring and fuel pump spacer to the fuel pump.


ii.

Engage the 3 claws to install the fuel pump to the fuel filter.

NOTICE:
·

Make sure that the O-ring is not cut or pinched during the installation.

·

Securely engage the claws.

·

Do not remove the suction filter from the fuel pump.




iii.
A401838

Connect the fuel pump harness connector to install the fuel pump harness to the fuel pump.


iv.
A401711

Engage the claw to connect the fuel pump harness to the fuel pump.

NOTICE:
·

Securely engage the claw.

·

Make sure that there is no foreign matter between the fuel pump and the ground terminal of the fuel pump harness.

·

Make sure that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.




v.

Check the connection state of the fuel pump harness.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fuel pump body - Ground terminal of the fuel pump harness Always Below 50 Ω


If the result is not as specified, reconnect the fuel pump harness to the fuel pump so that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.


vi.

Apply gasoline to a new O-ring. Then install the O-ring to the fuel sub-tank.


vii.
A401698

Install the fuel filter to the fuel sub-tank as shown in the illustration.

NOTICE:

Make sure that the O-ring is not cut or pinched during installation.



viii.

Engage the 3 claws.

NOTICE:

Securely engage the claws.



ix.

Engage the clamp to connect the tube to the fuel filter.


x.

Engage the clamp to connect the fuel pump harness to the fuel suction plate sub-assembly.


xi.

Connect the 2 fuel pump harness connectors.


xii.

Install the harness protector to the fuel pump harness.



b.

for Type B:

i.
A345414C04
2.323,0.583 2.375,0.427 2.375,0.427 2.531,0.427 false 2.323,0.771 2.677,0.771 false 2.583,0.344 2.896,0.5 0.313,0.156 10 false *1 2.74,0.698 3.052,0.854 0.313,0.156 10 false *2
*1 O-ring
*2 Fuel Pump Spacer


Apply gasoline to a new O-ring. Then install the O-ring and fuel pump spacer to the fuel pump.


ii.

Engage the 3 claws to install the fuel pump to the fuel filter.

NOTICE:
·

Make sure that the O-ring is not cut or pinched during the installation.

·

Securely engage the claws.

·

Do not remove the suction filter from the fuel pump.




iii.
A502676

Connect the fuel pump harness connector to install the fuel pump harness to the fuel pump.


iv.
A502672

Engage the claw to connect the fuel pump harness to the fuel pump.

NOTICE:
·

Securely engage the claw.

·

Make sure that there is no foreign matter between the fuel pump and the ground terminal of the fuel pump harness.

·

Make sure that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.




v.

Check the connection state of the fuel pump harness.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Fuel pump body - Ground terminal of the fuel pump harness Always Below 50 Ω


If the result is not as specified, reconnect the fuel pump harness to the fuel pump so that the ground terminal of the fuel pump harness is securely connected to the fuel pump body.


vi.

Engage the 2 claws to install the fuel filter to the fuel sub-tank.

NOTICE:
·

Do not apply excessive force to the tube or No. 1 fuel suction support.

·

Securely engage the claws.




vii.
A406553

Engage the clamp and claw, and connect the fuel pump filter hose while aligning it with the installation position of the fuel sub-tank.

NOTICE:

Securely engage the clamp and claw.



viii.

Engage the clamp to connect the fuel pump harness to the fuel suction plate sub-assembly.


ix.

Connect the 2 fuel pump harness connectors.


x.

Install the harness protector to the fuel pump harness.