Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD) › 2017.12–2018.04
RM33A0E _54 Brake _065365 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0319138 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake actuator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of brake actuator assembly Operate the electric parking brake switch (electric parking brake switch assembly) Parking brake indicator light (red) blinks when the ignition switch is first turned on (IG) (Click here)
Perform system variant learning and acceleration sensor zero point calibration.
·

VSC disabled or malfunctioning

·

DTCs are output

·

Slip indicator light illuminated

·

ABS warning light illuminated


(Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 28800 2.REMOVE BATTERY

Hide 3.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 4.REMOVE FRONT WHEEL LH

Hide 55708 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 6.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

a.
C376029

Disconnect the connector.


b.

Disengage the 3 clamps and separate the wire harness.


c.
C377997

Remove the 6 bolts, 4 nuts and front center upper suspension brace sub-assembly.


Hide 7.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for 2AR-FE)

Hide 8.REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for 2GR-FKS)

Hide 74404A 9.REMOVE BATTERY CLAMP SUB-ASSEMBLY

a.
C380324

Disengage the 5 clamps from the battery clamp sub-assembly.


b.

Remove the 3 bolts, nut and battery clamp sub-assembly.


Hide 10.REMOVE BRAKE ACTUATOR WITH BRACKET

a.
C376030C01
0,0 0,0 false
V113147

Release the lock lever
V113148

Disconnect the connector


Release the lock lever and disconnect the connector from the brake actuator assembly.

NOTICE:

Be careful not to allow any brake fluid to enter the connector.



b.
C376032C01
1.448,1.521 1.708,1.521 1.708,1.521 1.865,1.229 true 2.708,1.448 2.469,1.448 2.469,1.448 2.146,1.063 true 1.208,1.042 1.615,1.042 true 1.063,0.417 1.302,0.417 1.302,0.417 1.771,0.938 true 2.229,0.24 2.031,0.24 2.031,0.24 1.927,0.813 true 2.083,0.74 2.573,0.74 true 2.729,1.354 2.906,1.531 0.177,0.177 10 true *a 1.26,1.438 1.438,1.615 0.177,0.177 10 true *b 2.583,0.646 2.75,0.823 0.167,0.177 10 true *c 2.24,0.156 2.427,0.333 0.188,0.177 10 true *d 0.896,0.333 1.063,0.51 0.167,0.177 10 true *e 1.031,0.958 1.198,1.125 0.167,0.167 10 true *f
*a From 1st Chamber of Brake Master Cylinder Sub-assembly
*b From 2nd Chamber of Brake Master Cylinder Sub-assembly
*c To Front Wheel Cylinder Assembly RH
*d To Rear Wheel Cylinder Assembly LH
*e To Rear Wheel Cylinder Assembly RH
*f To Front Wheel Cylinder Assembly LH


Use tags or make a memo to identify the places to reconnect the brake lines.


c.
C376033

Using a union nut wrench, disconnect the 6 brake lines from the brake actuator assembly.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.




d.
C376034

Using a union nut wrench, disconnect the front No. 5 brake tube while holding the front flexible hose with a wrench.

NOTICE:
·

Do not kink or damage the front No. 5 brake tube.

·

Do not allow any foreign matter such as dirt or dust to enter the front No. 5 brake tube from the connecting parts.




e.
C376036

Disengage the clamp and separate the front No. 5 brake tube.

NOTICE:

Do not kink or damage the front No. 5 brake tube.



f.
C376037

Move aside the front No. 5 brake tube as shown in the illustration.

NOTICE:

Do not apply excessive force to the front No. 5 brake tube.



g.
C376038

Disengage the clamp and remove the brake tube clamp.


h.
C376039C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the vehicle body as shown in the illustration.


i.
C376041

Remove the 2 bolts, nut and brake actuator with bracket.

NOTICE:
·

Do not kink or damage the brake lines.

·

Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

·

Be careful not to allow any brake fluid to enter the connector.

·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator with bracket when carrying it.



HINT:

Remove the brake actuator with bracket while avoiding the brake lines.



Hide 44510 11.REMOVE BRAKE ACTUATOR ASSEMBLY

a.
C376042

Loosen the 2 nuts.


b.

Remove the bolt and brake actuator assembly from the brake actuator bracket assembly.

NOTICE:
·

Do not hold the brake actuator assembly by the connector.

·

Do not drop the brake actuator assembly when carrying it.




Hide 44521B 12.REMOVE NO. 2 BRAKE ACTUATOR CASE COLLAR

a.
C376043

Remove the No. 2 brake actuator case collar from the brake actuator bolt cushion.


Hide 44546A 13.REMOVE BRAKE ACTUATOR BOLT CUSHION

a.
C376044

Remove the brake actuator bolt cushion from the brake actuator bracket assembly.