Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2017.12
RM33A0E _59 Vehicle Exterior _065394 WIPER / WASHER _0320457 WIPER AND WASHER SYSTEM C

WIPER / WASHER  WIPER AND WASHER SYSTEM  B1373  Lost Communication with Wiper System LIN BUS  


DESCRIPTION

The main body ECU (multiplex network body ECU) and windshield wiper motor assembly communicate via LIN communication. The main body ECU (multiplex network body ECU) stores this DTC if communication becomes abnormal.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory DTC Output from
B1373 Lost Communication with Wiper System LIN BUS
Detection condition:

Battery voltage is 9.5 V or more


Malfunction Status:

A malfunction in the communication or LIN communication line between the main body ECU (multiplex network body ECU) and components of the wiper system occurs


Malfunction Time:

7 seconds or more 3 times consecutively


·

Windshield wiper motor assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector

·

Rain sensor*


○ Main Body

*: w/ Auto Wiper System


WIRING DIAGRAM

E378085E03
0.083,1.156 1.771,1.354 1.688,0.198 10 false K51 0.073,1.323 3.25,1.688 3.177,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 0.813,3.302 2.5,3.5 1.688,0.198 10 false : LIN Communication Line 2.219,0.615 3.906,0.813 1.688,0.198 10 false LIN3 2.615,0.448 2.896,0.656 0.281,0.208 10 false 3 4.625,0.615 6.313,0.813 1.688,0.198 10 false LIN 4.74,1.156 6.427,1.354 1.688,0.198 10 false A31 4.74,1.313 7.104,1.615 2.365,0.302 10 false Windshield Wiper Motor Assembly 4.625,2.583 6.313,2.781 1.688,0.198 10 false MPX 5.323,3.313 6.635,3.563 1.313,0.25 10 false Rain Sensor*3 4,0.448 4.729,0.656 0.729,0.208 10 false 2*1, 3*2 4.438,2.438 4.719,2.646 0.281,0.208 10 false 3 5.313,3.135 6.219,3.469 0.906,0.333 10 false V4*1, V5*2 0.635,2.208 2.323,2.406 1.688,0.198 10 false *1: for LHD 0.635,2.583 2.323,2.781 1.688,0.198 10 false *2: for RHD 3.625,1.26 3.938,1.458 0.313,0.198 10 false *3 0.635,2.948 2.49,3.208 1.854,0.26 10 false *3: w/ Auto Wiper System

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*1

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*2

*1: w/ Door Control Battery

*2: w/ Smart Entry and Start System




PROCEDURE

1.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Auto Wiper System A
w/ Auto Wiper System B



A

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY)

B

4.CHECK RAIN SENSOR
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY)
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the A31 windshield wiper motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K51-3 (LIN3) or A31-2 (LIN) - Body ground*1 Always 10 kΩ Higher
K51-3 (LIN3) or A31-3 (LIN) - Body ground*2 Always 10 kΩ Higher


*1: for LHD

*2: for RHD



Result:
Proceed to
OK
NG



OK

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
E366392C08
1.5,0.25 1.917,0.5 0.417,0.25 0.76,1.646 1.167,0.917 false 1.583,0.292 1.99,0.531 0.406,0.24 10 false K51 0.604,1.719 0.938,1.917 0.333,0.198 10 false LIN3 0.156,0.125 0.469,0.323 0.313,0.198 10 false *a
*a Component without harness connected
(Main Body ECU (Multiplex Network Body ECU)


a.

Check for voltage and pulses according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K51-3 (LIN3) - Body ground Ignition switch off Below 1 V
Ignition switch ON Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.CHECK RAIN SENSOR
a.

Disconnect the V4*1 or V5*2 rain sensor connector.

*1: for LHD

*2: for RHD



b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Turn the ignition switch to ON and wait for at least 10 seconds.


d.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B1279 is output A
DTC B1373 is output B



A

B

5.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY
5.CHECK WINDSHIELD WIPER MOTOR ASSEMBLY
a.

Disconnect the A31 windshield wiper motor assembly connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Turn the ignition switch to ON and wait for at least 10 seconds.


d.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
Only DTC B1245 is output A
DTC B1373 is output B



A

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

B

6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY AND RAIN SENSOR)
6.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - WINDSHIELD WIPER MOTOR ASSEMBLY AND RAIN SENSOR)
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

c.

Turn the ignition switch to ON and wait for at least 10 seconds.


d.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B1373 is not output A
DTC B1373 is output B



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)