Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System) › 2017.12–2021.02
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0341635 LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System)  Hazard Warning Switch Circuit  


DESCRIPTION

The combination meter assembly receives the hazard warning signal switch assembly on signal and controls the operation of the hazard warning lights.

WIRING DIAGRAM

E367346E01
1.729,1.74 4.302,1.99 2.573,0.25 10 false Hazard Warning Signal Switch Assembly 1.729,1.594 2.021,1.833 0.292,0.24 10 false M2 1.948,1.094 2.24,1.333 0.292,0.24 10 false 1 2.115,1.094 2.406,1.333 0.292,0.24 10 false E 3.448,1.104 3.74,1.344 0.292,0.24 10 false TB 3.698,1.094 3.99,1.333 0.292,0.24 10 false 4 5.229,1.938 5.521,2.177 0.292,0.24 10 false K20 5.219,2.073 7.115,2.354 1.896,0.281 10 false Combination Meter Assembly 5.531,1.031 5.969,1.25 0.438,0.219 10 false HAZ 5.354,1.083 5.646,1.323 0.292,0.24 10 false 3 6.302,0.573 6.74,0.792 0.438,0.219 10 false +B

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Body Electrical > Combination Meter > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Hazard Flasher Switch Hazard warning signal switch signal OFF or ON OFF: Hazard warning signal switch off
ON: Hazard warning signal switch on
-
Body Electrical > Combination Meter > Data List
Tester Display
Hazard Flasher Switch
50003 409 39
OK:

Normal conditions listed above are displayed.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY
a.

Remove the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>REMOVAL


b.

Inspect the hazard warning signal switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>HAZARD WARNING SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)

NG

REPLACE HAZARD WARNING SIGNAL SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (HAZARD WARNING SIGNAL SWITCH ASSEMBLY - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the K20 combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-4 (TB) - K20-3 (HAZ) Always Below 1 Ω
M2-4 (TB) or K20-3 (HAZ) - Body ground Always 10 kΩ or higher
M2-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR