Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System) › from 2017.12
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0341635 LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System)  Taillight Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the TAIL relay.

WIRING DIAGRAM

E367352E13
0.896,1 2.052,1.333 1.156,0.333 10 false from Battery 2.469,1.156 2.969,1.375 0.5,0.219 10 false ALT 4.74,1.521 5.094,1.75 0.354,0.229 10 false TAIL 5.313,1.417 5.667,1.646 0.354,0.229 10 false TAIL 6,0.906 6.427,1.135 0.427,0.229 10 false TRLY 3.823,3.208 5.427,3.604 1.604,0.396 10 false Instrument Panel Junction Block Assembly 5.396,3.76 7.031,4.708 1.635,0.948 10 false Main Body ECU (Multiplex Network Body ECU) 5.396,3.604 5.75,3.833 0.354,0.229 10 false MB 5.771,0.896 6.125,1.125 0.354,0.229 10 false 14 3.5,1.74 3.854,1.969 0.354,0.229 10 false 3C 3.49,1.563 3.844,1.792 0.354,0.229 10 false 32 3.49,2.76 3.844,2.99 0.354,0.229 10 false 3D 3.5,2.573 3.854,2.802 0.354,0.229 10 false 30 1.354,1.708 2.854,2.5 1.5,0.792 10 false to Clearance Lights and FOG FR Relay* 3.5,1.031 3.854,1.26 0.354,0.229 10 false 3F 3.531,0.844 3.885,1.073 0.354,0.229 10 false 1 0.594,2.75 2.875,3.646 2.281,0.896 10 false to Taillights and License Plate Lights 0.698,3.969 3.177,4.354 2.479,0.385 10 false *: w/ Front Fog Light

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System




PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Taillight Relay Taillight relay OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Taillight Relay
50004 123 13
OK:

Taillights illuminate.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (POWER SOURCE - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3F instrument panel junction block assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3F-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367362C01
1.479,0.344 1.844,0.552 0.365,0.208 4.875,0.729 5.25,0.948 0.375,0.219 2.323,2.042 2.688,2.25 0.365,0.208 5.083,2.031 5.448,2.24 0.365,0.208 4.677,1.542 4.844,1.208 false 0.302,0.177 0.615,0.375 0.313,0.198 10 false *a 1.573,0.375 1.885,0.573 0.313,0.198 10 false 3C 2.427,2.063 2.74,2.26 0.313,0.198 10 false 3D 4.948,0.75 5.26,0.948 0.313,0.198 10 false MB 4.51,1.563 5.01,1.802 0.5,0.24 10 false TRLY 5.188,2.052 5.5,2.25 0.313,0.198 10 false 3F
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the battery to terminal 3F-1.


d.

Connect a negative (-) lead from the battery to terminal MB-14 (TRLY).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3C-32 - Battery negative (-) terminal Always 11 to 14 V
3D-30 - Battery negative (-) terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY