Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System) › from 2017.12
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0341635 LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System) C

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System)  B2430  LED Headlight LH  B2431  LED Headlight RH  


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a communication malfunction is detected between the light control ECU and main body ECU (multiplex network body ECU).

HINT:

DTC B2430 or DTC B2431 may also be stored if a headlight cooling fan is malfunctioning. In this case, the light control ECU will dim or turn off the malfunctioning low beam headlight.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2430 LED Headlight LH
Detection condition:

All of the following conditions are met:

-

Engine running

-

Low beam headlights on



Malfunction Status:

Any of the following conditions is met:

-

Light control ECU malfunction

-

Headlight LED unit assembly LH malfunction

-

Light control ECU power source and signal malfunction



Malfunction Time:

10 seconds or more


·

Headlight LED unit assembly LH

·

Headlight unit assembly LH

·

Light control ECU

·

H-LP LH relay

·

Instrument panel junction block assembly

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


Main Body
B2431 LED Headlight RH
Detection condition:

All of the following conditions are met:

-

Engine running

-

Low beam headlights on



Malfunction Status:

Any of the following conditions is met:

-

Light control ECU malfunction

-

Headlight LED unit assembly RH malfunction

-

Light control ECU power source and signal malfunction



Malfunction Time:

10 seconds or more


·

Headlight LED unit assembly RH

·

Headlight unit assembly RH

·

Light control ECU

·

H-LP RH relay

·

Main body ECU (multiplex network body ECU)

·

Harness or connector


Main Body

WIRING DIAGRAM

E367078E07
0.698,0.344 2.531,0.542 1.833,0.198 10 false from Battery 0.698,1.729 2.531,1.927 1.833,0.198 10 false from Battery 0.625,1 2.458,1.198 1.833,0.198 10 false H-LP LH 1.917,1.385 2.563,1.635 0.646,0.25 10 false H-LP LH 1.927,2.76 2.573,3.01 0.646,0.25 10 false H-LP RH 0.635,2.385 1.281,2.635 0.646,0.25 10 false H-LP RH 4.198,1.104 4.844,1.354 0.646,0.25 10 false 3C 4.208,0.906 4.854,1.156 0.646,0.25 10 false 31 2.448,0.99 2.646,1.198 0.198,0.208 10 false 1 1.813,1 2.01,1.208 0.198,0.208 10 false 2 1.813,0.74 2.01,0.948 0.198,0.208 10 false 5 2.448,0.74 2.646,0.948 0.198,0.208 10 false 3 5.802,0.906 6.448,1.156 0.646,0.25 10 false 15 5.792,1.104 6.438,1.354 0.646,0.25 10 false MB 6.156,1.01 6.802,1.26 0.646,0.25 10 false HRLY 2.406,4.063 3.052,4.313 0.646,0.25 10 false LO 1.729,4.646 2.375,4.896 0.646,0.25 10 false E 2.49,4.656 3.135,4.906 0.646,0.25 10 false S 2.698,3.958 3.344,4.208 0.646,0.25 10 false 3 1.542,4.552 2.188,4.802 0.646,0.25 10 false 1 2.698,4.531 3.344,4.781 0.646,0.25 10 false 2 1.396,4.969 2.771,5.25 1.375,0.281 10 false A74 5.813,4.469 6.458,4.719 0.646,0.25 10 false 14 5.771,4.656 6.417,4.906 0.646,0.25 10 false K51 6.729,4.167 6.99,4.417 0.26,0.25 10 false IG 6.729,6.042 6.99,6.292 0.26,0.25 10 false IG 6.146,4.542 6.792,4.792 0.646,0.25 10 false LLEW 6.146,6.427 6.792,6.677 0.646,0.25 10 false RLEW 5.813,6.344 6.156,6.542 0.344,0.198 10 false 15 5.781,6.531 6.427,6.781 0.646,0.25 10 false K51 2.5,6.531 3.146,6.781 0.646,0.25 10 false S 2.417,5.938 3.063,6.188 0.646,0.25 10 false LO 1.729,6.531 2.375,6.781 0.646,0.25 10 false E 1.333,6.854 2.844,7.208 1.51,0.354 10 false A73 1.396,5.094 3.208,5.5 1.813,0.406 10 false Headlight Assembly LH 1.333,6.979 3.167,7.292 1.833,0.313 10 false Headlight Assembly RH 1.813,2.135 2.01,2.344 0.198,0.208 10 false 5 1.813,2.396 2.01,2.604 0.198,0.208 10 false 2 2.458,2.135 2.656,2.344 0.198,0.208 10 false 3 2.458,2.396 2.656,2.604 0.198,0.208 10 false 1 6.156,2.375 6.802,2.625 0.646,0.25 10 false HRY2 5.771,2.49 6.417,2.74 0.646,0.25 10 false K52 5.813,2.292 6.458,2.542 0.646,0.25 10 false 12 5.51,6.969 7.156,7.458 1.646,0.49 10 false Main Body ECU (Multiplex Network Body ECU) 4.49,1.615 6.104,2.167 1.615,0.552 10 false Instrument Panel Junction Block Assembly 2.719,5.833 3.365,6.083 0.646,0.25 10 false 3 2.719,6.438 3.365,6.688 0.646,0.25 10 false 2 1.542,6.417 2.188,6.667 0.646,0.25 10 false 1

HEADLIGHT ASSEMBLY CIRCUIT


E389370E01
4.51,0.802 4.667,1 0.156,0.198 10 false C 4.5,0.406 4.656,0.604 0.156,0.198 10 false C 4.5,1.208 4.656,1.406 0.156,0.198 10 false C 4.5,2.073 4.656,2.271 0.156,0.198 10 false D 4.49,1.604 4.646,1.802 0.156,0.198 10 false D 4.5,3.24 4.656,3.438 0.156,0.198 10 false E 4.5,2.865 4.656,3.063 0.156,0.198 10 false E 4.5,0.229 4.656,0.427 0.156,0.198 10 false 3 4.5,0.615 4.656,0.813 0.156,0.198 10 false 2 4.5,1.021 4.656,1.219 0.156,0.198 10 false 1 4.094,0.292 4.25,0.49 0.156,0.198 10 false 2 4.104,0.688 4.26,0.885 0.156,0.198 10 false 9 4.083,1.083 4.396,1.281 0.313,0.198 10 false 11 4.083,1.49 4.396,1.688 0.313,0.198 10 false 10 4.104,1.969 4.26,2.167 0.156,0.198 10 false 4 4.5,1.427 4.656,1.625 0.156,0.198 10 false 2 4.5,1.885 4.656,2.083 0.156,0.198 10 false 1 4.49,2.667 4.646,2.865 0.156,0.198 10 false 2 4.49,3.052 4.646,3.25 0.156,0.198 10 false 1 2.844,2.385 3,2.583 0.156,0.198 10 false B 2.833,2.521 5.438,2.719 2.604,0.198 10 false Light Control ECU 3.635,0.396 4.25,0.594 0.615,0.198 10 false FAN+ 3.625,0.792 4.24,0.99 0.615,0.198 10 false FANS 3.667,1.198 4.281,1.396 0.615,0.198 10 false FAN- 3.656,1.594 4.271,1.792 0.615,0.198 10 false LED+ 3.677,2.073 4.292,2.271 0.615,0.198 10 false LED- 2.656,0.385 3.885,0.583 1.229,0.198 10 false +B (H/L) 2.656,1.375 3.115,1.573 0.458,0.198 10 false WNG 2.667,2.031 3.125,2.229 0.458,0.198 10 false GND 2.448,0.271 2.604,0.469 0.156,0.198 10 false 7 2.385,1.271 2.698,1.469 0.313,0.198 10 false 12 2.438,1.927 2.594,2.125 0.156,0.198 10 false 6 0.26,0.375 0.417,0.573 0.156,0.198 10 false 3 0.26,1.375 0.417,1.573 0.156,0.198 10 false 2 0.26,2.031 0.417,2.229 0.156,0.198 10 false 1 0.26,3.24 0.417,3.438 0.156,0.198 10 false 4 5.448,1.5 6.792,1.854 1.344,0.354 10 false Headlight Fan 5.344,1.854 6.875,2.052 1.531,0.198 10 false Lo/Hi Beam 0.479,0.271 0.792,0.469 0.313,0.198 10 false LO 0.49,1.281 0.646,1.479 0.156,0.198 10 false S 0.49,1.917 0.948,2.115 0.458,0.198 10 false E 0.49,3.125 0.948,3.323 0.458,0.198 10 false SOL 5.292,3.563 6.604,3.854 1.313,0.292 10 false Lo/Hi Beam Shade 4.833,3.958 6.823,4.26 1.99,0.302 10 false Headlight LED Unit Assembly 2.479,5.792 2.635,5.99 0.156,0.198 10 false G 2.469,4.75 2.625,4.948 0.156,0.198 10 false G 2.469,5.104 2.625,5.302 0.156,0.198 10 false G 2.479,5.448 2.635,5.646 0.156,0.198 10 false G 2.469,8.448 2.625,8.646 0.156,0.198 10 false F 2.469,6.365 2.625,6.563 0.156,0.198 10 false F 2.469,6.698 2.625,6.896 0.156,0.198 10 false F 2.469,7.042 2.625,7.24 0.156,0.198 10 false F 2.469,7.396 2.625,7.594 0.156,0.198 10 false F 2.469,7.75 2.625,7.948 0.156,0.198 10 false F 2.469,8.094 2.625,8.292 0.156,0.198 10 false F 2.469,4.563 2.625,4.76 0.156,0.198 10 false 5 2.458,4.927 2.615,5.125 0.156,0.198 10 false 4 2.469,5.281 2.625,5.479 0.156,0.198 10 false 3 2.458,5.615 2.615,5.813 0.156,0.198 10 false 1 2.469,6.167 2.625,6.365 0.156,0.198 10 false 7 2.469,6.531 2.625,6.729 0.156,0.198 10 false 6 2.479,6.875 2.635,7.073 0.156,0.198 10 false 5 2.479,7.219 2.635,7.417 0.156,0.198 10 false 4 2.469,7.573 2.625,7.771 0.156,0.198 10 false 2 2.469,7.917 2.625,8.115 0.156,0.198 10 false 1 2.479,8.271 2.635,8.469 0.156,0.198 10 false 3 0.26,7.74 0.417,7.938 0.156,0.198 10 false 5 0.26,8.083 0.417,8.281 0.156,0.198 10 false 6 0.479,7.99 0.635,8.188 0.156,0.198 10 false B 0.479,7.625 0.635,7.823 0.156,0.198 10 false B 2.969,4.927 4.427,6.01 1.458,1.083 10 false Electronic Light Source Control Gear A 2.969,6.698 4.427,7.781 1.458,1.083 10 false Electronic Light Source Control Gear B 5.083,5.313 6.615,6.229 1.531,0.917 10 false Clearance Light/Daytime Running Light 3.729,8.771 6.417,9.063 2.688,0.292 10 false No. 1 Headlight Clearance LED Unit 2.781,9.313 6.302,9.51 3.521,0.198 10 false Headlight Unit Assembly


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System




PROCEDURE

1.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123
OK:

DTC B2430 and B2431 are not output.



Result:
Result Proceed to
OK A
NG (DTC B2430 is output) B
NG (DTC B2431 is output) C



A

B

3.INSPECT HEADLIGHT ASSEMBLY LH (LO TERMINAL VOLTAGE)

C

16.INSPECT HEADLIGHT ASSEMBLY RH (LO TERMINAL VOLTAGE)
3.INSPECT HEADLIGHT ASSEMBLY LH (LO TERMINAL VOLTAGE)
E367359C05
1.542,0.667 1.906,0.948 0.365,0.281 2.417,2.708 2.052,1.823 false 1.604,0.719 2.063,0.917 0.458,0.198 10 false A74 0.25,0.344 0.708,0.542 0.458,0.198 10 false *a 2.385,2.76 2.844,2.958 0.458,0.198 10 false LO
*a Front view of wire harness connector
(to Headlight Assembly LH)


a.

Disconnect the A74 headlight assembly LH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A74-3 (LO) - Body ground Light control switch in head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - BODY GROUND)

NG

11.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ASSEMBLY LH)
4.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT HEADLIGHT ASSEMBLY LH (S TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT HEADLIGHT ASSEMBLY LH (S TERMINAL VOLTAGE)
E367359C06
1.542,0.667 1.906,0.948 0.365,0.281 2.052,2.813 1.698,1.823 false 1.604,0.719 2.063,0.917 0.458,0.198 10 false A74 0.25,0.344 0.708,0.542 0.458,0.198 10 false *a 2.042,2.823 2.5,3.021 0.458,0.198 10 false S
*a Front view of wire harness connector
(to Headlight Assembly LH)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A74-2 (S) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.INSPECT HEADLIGHT UNIT ASSEMBLY LH

NG

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
6.INSPECT HEADLIGHT UNIT ASSEMBLY LH
E387963C01
3.552,0.469 3.875,0.698 0.323,0.229 1.104,0.344 1.49,0.583 0.385,0.24 5.76,0.604 6.104,0.823 0.344,0.219 0.385,2.167 1.021,1.156 false 1.542,2.167 1.292,1.167 false 2.188,2.167 1.604,1.167 false 0.271,0.552 0.583,0.75 0.313,0.198 10 false *a 2.688,0.563 3,0.76 0.313,0.198 10 false *b 3.667,0.5 3.823,0.698 0.156,0.198 10 false B 1.177,0.375 1.635,0.573 0.458,0.198 10 false A74 2.177,2.177 2.635,2.375 0.458,0.198 10 false E 1.521,2.188 1.677,2.385 0.156,0.198 10 false S 0.281,2.188 0.594,2.385 0.313,0.198 10 false LO 5.135,0.563 5.448,0.76 0.313,0.198 10 false *c 5.885,0.635 6.042,0.833 0.156,0.198 10 false D
*a Component without harness connected
(to Wire Harness)
*b Component without harness connected
(to Light Control ECU)
*c Component without harness connected
(to Headlight LED Unit Assembly LH)
- -




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-1 (E) - B-6 Always Below 1 Ω
A74-2 (S) - B-12 Always Below 1 Ω
A74-3 (LO) - B-7 Always Below 1 Ω
B-4 - D-1 Always Below 1 Ω
B-10 - D-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK LIGHT CONTROL ECU

NG

7.CHECK LIGHT CONTROL ECU
a.

Remove each light control ECU, interchange the light control ECU (for LH) with (for RH) and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

8.CLEAR DTC
8.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2430 is output A
DTC B2431 is output B



A

B

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A74-2 (S) - K51-14 (LLEW) Always Below 1 Ω
A74-2 (S) or K51-14 (LLEW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - HEADLIGHT ASSEMBLY LH)
a.

Remove the H-LP LH relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP LH relay) - A74-3 (LO) Always Below 1 Ω
3 (H-LP LH relay) or A74-3 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT H-LP LH RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT H-LP LH RELAY
a.

Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY)

NG

REPLACE H-LP LH RELAY

13.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP LH RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (H-LP LH relay) - Body ground Always 11 to 14 V
5 (H-LP LH relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (H-LP LH RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP LH relay) - 3C-31 Always Below 1 Ω
1 (H-LP LH relay) or 3C-31 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367360C01
1.74,0.583 2.115,0.833 0.375,0.25 4.875,0.938 5.25,1.188 0.375,0.25 4.563,2.052 4.938,1.542 false 0.479,0.438 0.792,0.635 0.313,0.198 10 false *a 1.844,0.635 2.156,0.833 0.313,0.198 10 false 3C 4.948,0.979 5.26,1.177 0.313,0.198 10 false MB 4.396,2.083 4.927,2.313 0.531,0.229 10 false HRLY
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-31 - MB-15 (HRLY) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

16.INSPECT HEADLIGHT ASSEMBLY RH (LO TERMINAL VOLTAGE)
E367359C07
1.542,0.667 1.906,0.948 0.365,0.281 2.417,2.708 2.052,1.823 false 1.604,0.719 2.063,0.917 0.458,0.198 10 false A73 0.25,0.344 0.708,0.542 0.458,0.198 10 false *a 2.385,2.76 2.844,2.958 0.458,0.198 10 false LO
*a Front view of wire harness connector
(to Headlight Assembly RH)


a.

Disconnect the A73 headlight assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-3 (LO) - Body ground Light control switch in head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

17.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - BODY GROUND)

NG

24.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ASSEMBLY RH)
17.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.INSPECT HEADLIGHT ASSEMBLY RH (S TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.INSPECT HEADLIGHT ASSEMBLY RH (S TERMINAL VOLTAGE)
E367359C08
1.542,0.667 1.906,0.948 0.365,0.281 2.052,2.813 1.698,1.823 false 1.604,0.719 2.063,0.917 0.458,0.198 10 false A73 0.25,0.344 0.708,0.542 0.458,0.198 10 false *a 2.042,2.823 2.5,3.021 0.458,0.198 10 false S
*a Front view of wire harness connector
(to Headlight Assembly RH)


a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A73-2 (S) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

19.INSPECT HEADLIGHT UNIT ASSEMBLY RH

NG

23.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
19.INSPECT HEADLIGHT UNIT ASSEMBLY RH
E387963C02
3.542,0.438 3.865,0.667 0.323,0.229 1.125,0.313 1.51,0.552 0.385,0.24 5.771,0.573 6.094,0.802 0.323,0.229 0.573,2.156 0.99,1.156 false 1.646,2.156 1.313,1.156 false 2.281,2.135 1.667,1.125 false 0.375,0.479 0.688,0.677 0.313,0.198 10 false *a 2.729,0.49 3.042,0.688 0.313,0.198 10 false *b 3.656,0.469 3.813,0.667 0.156,0.198 10 false B 1.198,0.354 1.656,0.552 0.458,0.198 10 false A73 2.271,2.167 2.729,2.365 0.458,0.198 10 false E 1.625,2.188 1.781,2.385 0.156,0.198 10 false S 0.458,2.177 0.771,2.375 0.313,0.198 10 false LO 5.167,0.531 5.479,0.729 0.313,0.198 10 false *c 5.885,0.604 6.042,0.802 0.156,0.198 10 false D
*a Component without harness connected
(to Wire Harness)
*b Component without harness connected
(to Light Control ECU)
*c Component without harness connected
(to Headlight LED Unit Assembly RH)
- -




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-1 (E) - B-6 Always Below 1 Ω
A73-2 (S) - B-12 Always Below 1 Ω
A73-3 (LO) - B-7 Always Below 1 Ω
B-4 - D-1 Always Below 1 Ω
B-10 - D-2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.CHECK LIGHT CONTROL ECU

NG

20.CHECK LIGHT CONTROL ECU
a.

Remove each light control ECU, interchange the light control ECU (for RH) with (for LH) and connect the connectors.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY (for Bulb Type Turn Signal Light)>DISASSEMBLY


Result:
Proceed to
NEXT



NEXT

21.CLEAR DTC
21.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


e.

Clear the DTCs.

Body Electrical > Main Body > Clear DTCs
50002 123

Result:
Proceed to
NEXT



NEXT

22.CHECK FOR DTC
22.CHECK FOR DTC
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Operate the light control switch to turn on the low beam headlights and wait 10 seconds or more.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / Main Body / Trouble Codes.


f.

Check for DTCs.

Body Electrical > Main Body > Trouble Codes
50001 123

Result:
Result Proceed to
DTC B2431 is output A
DTC B2430 is output B



A

B

23.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K51 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A73-2 (S) - K51-15 (RLEW) Always Below 1 Ω
A73-2 (S) or K51-15 (RLEW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - HEADLIGHT ASSEMBLY RH)
a.

Remove the H-LP RH relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (H-LP RH relay) - A73-3 (LO) Always Below 1 Ω
3 (H-LP RH relay) or A73-3 (LO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

25.INSPECT H-LP RH RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

25.INSPECT H-LP RH RELAY
a.

Result:
Proceed to
OK
NG



OK

26.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY)

NG

REPLACE H-LP RH RELAY

26.CHECK HARNESS AND CONNECTOR (POWER SOURCE - H-LP RH RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
2 (H-LP RH relay) - Body ground Always 11 to 14 V
5 (H-LP RH relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

27.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (H-LP RH RELAY - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the K52 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (H-LP RH relay) - K52-12 (HRY2) Always Below 1 Ω
1 (H-LP RH relay) or K52-12 (HRY2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR