Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System) › from 2017.12
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0341635 LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System)  Daytime Running Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the daytime running lights.

WIRING DIAGRAM

E373204E06
1.417,5.229 3.333,5.521 1.917,0.292 10 false Headlight Assembly RH 1.417,5.073 1.76,5.344 0.344,0.271 10 false A73 1.375,3.26 1.719,3.531 0.344,0.271 10 false A74 1.375,3.406 3.281,3.677 1.906,0.271 10 false Headlight Assembly LH 2.688,4.24 3.031,4.51 0.344,0.271 10 false 6 2.479,2.583 2.823,2.854 0.344,0.271 10 false B 2.677,2.469 3.021,2.74 0.344,0.271 10 false 6 2.49,4.375 2.833,4.646 0.344,0.271 10 false B 1.729,2.958 2.177,3.198 0.448,0.24 10 false E 1.573,2.865 1.917,3.135 0.344,0.271 10 false 1 1.719,4.75 2.135,4.979 0.417,0.229 10 false E 1.573,4.646 1.917,4.917 0.344,0.271 10 false 1 2.031,1.479 2.375,1.75 0.344,0.271 10 false DRL 1.802,0.854 2.146,1.125 0.344,0.271 10 false 3 1.813,1.104 2.156,1.375 0.344,0.271 10 false 1 0.74,1.104 1.083,1.375 0.344,0.271 10 false DRL 2.458,1.115 2.802,1.385 0.344,0.271 10 false 2 2.458,0.844 2.802,1.115 0.344,0.271 10 false 5 0.698,0.458 1.667,0.781 0.969,0.323 10 false from Battery 4.208,1.219 4.552,1.49 0.344,0.271 10 false 3C 4.219,1.01 4.563,1.281 0.344,0.271 10 false 28 4.406,1.729 6.01,2.292 1.604,0.563 10 false Instrument Panel Junction Block Assembly 5.813,1.208 6.156,1.479 0.344,0.271 10 false MB 5.833,1.01 6.177,1.281 0.344,0.271 10 false 25 6.167,1.104 6.51,1.375 0.344,0.271 10 false DRL 5.448,2.823 7.094,3.365 1.646,0.542 10 false Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System




PROCEDURE

1.CHECK OPERATION (CLEARANCE LIGHTS)
a.

Check the operation of the clearance lights.

OK:

The clearance lights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Daytime Running Light Daytime running lights OFF or ON -
Body Electrical > Main Body > Active Test
Tester Display
Daytime Running Light
50004 123 29
OK:

Daytime running lights illuminate.



Result:
Proceed to
OK
NG



OK

NG

3.INSPECT DRL RELAY
3.INSPECT DRL RELAY

Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DRL RELAY)

NG

REPLACE DRL RELAY

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE - DRL RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (DRL relay) - Body ground Always 11 to 14 V
3 (DRL relay) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DRL RELAY - HEADLIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DRL RELAY - HEADLIGHT ASSEMBLY)
a.

Disconnect the A74 headlight assembly LH connector.


b.

Disconnect the A73 headlight assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (DRL relay) - A74-6 (B) Always Below 1 Ω
5 (DRL relay) - A73-6 (B) Always Below 1 Ω
5 (DRL relay) or A74-6 (B) - Body ground Always 10 kΩ or higher
5 (DRL relay) or A73-6 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (DRL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DRL RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 3C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (DRL relay) - 3C-28 Always Below 1 Ω
2 (DRL relay) or 3C-28 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E367360C02
1.74,0.583 2.115,0.833 0.375,0.25 4.875,0.938 5.25,1.188 0.375,0.25 5.552,2.052 5.927,1.542 false 0.479,0.438 0.792,0.635 0.313,0.198 10 false *a 1.844,0.635 2.156,0.833 0.313,0.198 10 false 3C 4.948,0.979 5.26,1.177 0.313,0.198 10 false MB 5.385,2.083 5.917,2.313 0.531,0.229 10 false DRL
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3C-28 - MB-25 (DRL) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY