If the air conditioning system cannot be operated using the air conditioning control panel (radio and display receiver assembly)*1 or air conditioning control assembly*2, the following factors may be the cause.
| Symptom | Factor |
|---|---|
| Air conditioning system cannot be operated using air conditioning control panel (radio and display receiver assembly)*1 or air conditioning control assembly*2
(With the exception of the switch indicators, no inputs are reflected when other switches operated) |
·
CAN communication malfunction between air conditioning amplifier assembly and air conditioning control panel (radio and display receiver assembly)*1 ·
LIN communication malfunction between air conditioning amplifier assembly and air conditioning control assembly*2 ·
Short to +B or ground in air conditioning amplifier assembly circuit ·
Air conditioning amplifier assembly malfunction ·
Air conditioning control panel (radio and display receiver assembly) malfunction*1 ·
Air conditioning control assembly malfunction*2 ·
Harness or connector |
*1: for 8 Inch Display
*2: except 8 Inch Display
for 8 Inch Display
except 8 Inch Display
Inspect the fuses for circuits related to this system before performing the following procedure.
| Result | Proceed to |
|---|---|
| for 8 Inch Display | A |
| except 8 Inch Display | B |
A
B
Disconnect the h1 air conditioning control panel (radio and display receiver assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h1-3 (+B) - Body ground | Always | 11 to 14 V |
| h1-10 (ACC) - Body ground | Ignition switch ACC | 11 to 14 V |
| h1-2 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| h1-6 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| B15F9 is not output | A |
| B15F9 is output | B |
A
B
Using the GTS, check for CAN communication system DTCs.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSTIC TROUBLE CODE CHART
| Result | Proceed to |
|---|---|
| CAN communication system DTCs are not output | A |
| CAN communication system DTCs are output | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Air Conditioner / Active Test.
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Blower Motor | Blower motor with fan sub-assembly | Min.: 0
Max.: 31 |
- |
| Tester Display |
|---|
| Blower Motor |
Blower motor with fan sub-assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| B14B2 is not output | A |
| B14B2 is output | B |
A
B
| *a | Front view of wire harness connector
(to Air Conditioning Amplifier Assembly) |
Disconnect the K54 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K54-4 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K54-1 (B) - Body ground | Always | 11 to 14 V |
| K54-2 (IG+) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG