The steering pad switch assembly outputs the on/off signal and various control signals to the ECM.
The ECM performs cruise control according to the signals received from the steering pad switch assembly.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Before replacing the ECM, refer to Service Bulletin.
| *1 | Steering Pad Switch Assembly |
| *a | Cruise Control Main Switch |
| *b | -SET Switch |
| *c | +RES Switch |
| *d | CANCEL Switch |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Cruise Control / Data List.
Check the Data List to confirm proper functioning of the steering pad switch assembly.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Cancel Switch | CANCEL switch status | ON or OFF | ON: CANCEL switch pushed
OFF: CANCEL switch not pushed |
- |
| -SET Switch | -SET switch status | ON or OFF | ON: -SET switch pushed
OFF: -SET switch not pushed |
- |
| +RES Switch | +RES switch status | ON or OFF | ON: +RES switch pushed
OFF: +RES switch not pushed |
- |
| Cruise Main Switch Operation Condition | Cruise control main switch status | ON or OFF | ON: Cruise control main switch pushed
OFF: Cruise control main switch not pushed |
- |
| Tester Display |
|---|
| Cancel Switch |
| -SET Switch |
| +RES Switch |
| Cruise Main Switch Operation Condition |
The value of each measurement item changes according to the operation of the steering pad switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM (except 2AR-FE)>PROBLEM SYMPTOMS TABLE
NG
Remove the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL
Inspect the steering pad switch assembly.
Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the K22 spiral cable sub-assembly connector.
Disconnect the A24 ECM connector (for A25A-FKS).
Disconnect the A23 ECM connector (for 2GR-FKS).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-27 (CCS) - K22-13 (CCS) | Always | Below 1 Ω |
| A24-28 (ECCS) - K22-2 (ECC) | Always | Below 1 Ω |
| A24-27 (CCS) or K22-13 (CCS) - Body ground | Always | 10 kΩ or higher |
| A24-28 (ECCS) or K22-2 (ECC) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-41 (CCS) - K22-13 (CCS) | Always | Below 1 Ω |
| K22-2 (ECC) - Body ground | Always | Below 1 Ω |
| A23-41 (CCS) or K22-13 (CCS) - Body ground | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (for A25A-FKS) | A |
| OK (for 2GR-FKS) | B |
| NG | C |
A
B
C
Disconnect the A24 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A24-10 (E1) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG