Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column) › 2017.12–2018.04
RM33A0E _55 Steering _065371 STEERING COLUMN _0319591 STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Manual Tilt and Manual Telescopic Steering Column)  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:
·

After the column is installed, check the tilt operation.

·

If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.

Tighten the nuts and check the tilt operation again.




b.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 45220 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C375256C01
1.573,0.76 1.01,0.656 1.01,0.656 1.583,0.688 true 0.854,0.563 1.021,0.75 0.167,0.188 10 true *a
*a Matchmark


Align the matchmarks on the steering intermediate shaft assembly and steering column assembly.


b.

Install the steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


d.
C375250

Tighten the clamp.


Hide 45253 4.INSTALL STEERING COLUMN HOLE COVER

a.
C373453

Install the steering column hole cover with the 2 clips.


b.

Install the clip.


c.

Return the floor carpet.


Hide 45220 5.CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 6.INSTALL FRONT WHEEL LH (for LHD)

Hide 7.INSTALL FRONT WHEEL RH (for RHD)

Hide 87211 8.INSTALL NO. 1 AIR DUCT (for LHD)

a.
C373452

Engage the 3 claws to install a new No. 1 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 87211 9.INSTALL NO. 1 AIR DUCT (for RHD)

a.
C378533

Engage the 3 claws to install a new No. 1 air duct.


b.

Install the 2 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 73900 10.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55302D 11.INSTALL NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

Hide 55434B 12.INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 55435B 13.INSTALL NO. 1 METER HOOD CLUSTER

Hide 53601 14.CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55436B 15.INSTALL NO. 2 METER HOOD CLUSTER

Hide 62312B 18.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Install the front door opening trim weatherstrip.

NOTICE:

After installation, check that the corners fit correctly.



Hide 62112A 19.INSTALL COWL SIDE TRIM SUB-ASSEMBLY

Hide 67914 20.INSTALL FRONT DOOR SCUFF PLATE

Hide 21.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.
C375251C01
1.146,0.542 1.427,0.542 false 0.99,0.448 1.302,0.604 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


b.

While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.


c.

Return the clamp to its original position.


d.

Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


Hide 89782 22.INSTALL TRANSPONDER KEY COIL (w/o Entry and Start System)

a.
C373458

Engage the 2 claws to install the transponder key coil.


b.

Connect the connector.


Hide 45286B 23.INSTALL UPPER STEERING COLUMN COVER

a.
C373450

Engage the 2 claws and 4 clips to connect the upper steering column cover.


b.
C375252C01
0,0 0,0 false
V113147

Install in this direction


Engage the claw to install the upper steering column cover.


Hide 45024 24.INSTALL LOWER STEERING COLUMN COVER SUB-ASSEMBLY

a.
C384440

Engage the 2 claws to install the lower steering column cover sub-assembly.


b.
C384438

Install the 3 screws.


Hide 25.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 84306 26.INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 27.INSTALL STEERING WHEEL ASSEMBLY

Hide 28.CHECK STEERING WHEEL CENTER POINT

Hide 45130 29.INSTALL HORN BUTTON ASSEMBLY

Hide 30. PERFORM INITIALIZATION AND CALIBRATION (w/ Parking Assist Monitor System)