Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column) › 2017.12–2018.04
RM33A0E _55 Steering _065371 STEERING COLUMN _0327257 STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for Power Tilt and Power Telescopic Steering Column)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during steering column assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: w/ Smart Entry and Start System

Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Steering sensor
·

Steering angle neutral point (Initialize parking assist monitor system)

·

Steering angle setting


Parking assist monitor system for Initialization:(Click here)
for Calibration:(Click here)
Steering lock ECU (steering lock actuator or upper bracket assembly)*1 Perform code registration (Immobiliser function)
·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.

PROCEDURE

Hide 2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS

a.

Disable the auto tilt away function by changing the customize settings.

Click hereSteering>STEERING COLUMN>POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM>CUSTOMIZE PARAMETERS

NOTICE:

Record the current customize setting (whether the auto tilt away function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the auto tilt away function to be disabled when the engine switch is turned off.



b.

Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.


Hide 3. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 4.REMOVE HORN BUTTON ASSEMBLY

Hide 5.REMOVE STEERING WHEEL ASSEMBLY

Hide 45024 6.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY

NOTICE:

Removing the lower steering column cover sub-assembly in the incorrect order will cause the parts to break.


a.
C379356

Remove the 3 screws.


b.
C379357C01
0,0 0,0 false
V100155

Push Area
V113147

Push in this direction


While pressing the push area shown in the illustration to disengage the 2 claws, slightly lower the lower steering column cover sub-assembly.


Hide 45286B 7.REMOVE UPPER STEERING COLUMN COVER

a.
C379358C02
0,0 0,0 false
V113147

Separate in this direction


Disengage the claw and separate the upper steering column cover.


b.
C379359

Disengage the 2 claws and 4 clips to remove the upper steering column cover.


Hide 8.REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not remove/install the spiral cable with sensor sub-assembly with the battery connected and the engine switch on (IG).

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the battery connected and the engine switch on (IG).

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.

Disconnect each connector from the turn signal switch assembly with spiral cable sub-assembly.


b.
C373451C01
1.698,0.521 1.99,0.521 false 2.031,0.427 2.344,0.583 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


c.

While holding the clamp expanded, raise the claw using a screwdriver to disengage it, and then remove the turn signal switch assembly with spiral cable sub-assembly from the steering column assembly.


Hide 67914 9.REMOVE FRONT DOOR SCUFF PLATE

Hide 62112A 10.REMOVE COWL SIDE TRIM SUB-ASSEMBLY

Hide 62312B 11.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

a.

Disconnect the front door opening trim weatherstrip.

HINT:

Disconnect the front door opening trim weatherstrip to the extent that allows the removal of the instrument side panel.



Hide 55318C 12.REMOVE INSTRUMENT SIDE PANEL

Hide 55606 13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 55436B 14.REMOVE NO. 2 METER HOOD CLUSTER

Hide 53601 15.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55435B 16.REMOVE NO. 1 METER HOOD CLUSTER

Hide 55434B 17.REMOVE LOWER CENTER INSTRUMENT PANEL FINISH PANEL

Hide 55302D 18.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY

Hide 73900 19.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 87211 20.REMOVE NO. 1 AIR DUCT (for LHD)

a.
C378964C01
1.427,0.167 1.74,0.323 0.313,0.156 10 false *a 1.615,2.604 1.76,2.781 0.146,0.177 10 true A
*a View A
V100137

Front


Remove the 2 bolts.


b.

Disengage the 3 claws to remove the No. 1 air duct.

NOTICE:

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.



Hide 87211 21.REMOVE NO. 1 AIR DUCT (for RHD)

a.
C379827C02
1.76,0.271 2.073,0.427 0.313,0.156 10 false *a 1.771,2.635 1.917,2.771 0.146,0.135 10 true A
*a View A
V100137

Front


Remove the 2 bolts.


b.

Disengage the 3 claws to remove the No. 1 air duct.

NOTICE:

Be careful not to deform or damage the lower heater case of the air conditioner unit assembly when removing the No. 1 air duct.



Hide 22.REMOVE FRONT WHEEL LH (for LHD)

Hide 23.REMOVE FRONT WHEEL RH (for RHD)

Hide 45220 24.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45253 25.REMOVE STEERING COLUMN HOLE COVER

a.

Turn back the floor carpet.


b.
C373453

Remove the clip.


c.

Disengage the 2 clips to remove the steering column hole cover.


Hide 45220 26.REMOVE STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C373454

Using a screwdriver, loosen the clamp as shown in the illustration.


b.
C379360C01
0.635,0.469 1.635,0.469 true 1.042,0.469 1.042,0.542 1.042,0.542 1.604,0.542 true 0.469,0.385 0.635,0.542 0.167,0.156 10 true *a
*a Matchmark


Remove the bolt and slide the steering intermediate shaft assembly.

NOTICE:

Do not remove the steering intermediate shaft assembly from the steering column assembly.



c.

Put matchmarks on the steering intermediate shaft assembly and steering column assembly.


d.

Remove the steering intermediate shaft assembly from the steering column assembly.


Hide 45250 27.REMOVE STEERING COLUMN ASSEMBLY

a.

Disconnect each connector and disengage each wire harness clamp from the steering column assembly.


b.
C379361

Remove the bolt, 2 nuts and steering column assembly.