Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2017.12–2018.04
RM33A0E _58 Vehicle Interior _065389 INTERIOR PANELS / TRIM _0325686 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during instrument panel safety pad removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)

CAUTION:
B401522

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. CHANGE POWER TILT AND POWER TELESCOPIC STEERING COLUMN SYSTEM SETTINGS (for Power Tilt and Power Telescopic Steering Column)

Hide 3.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 45130 4.REMOVE HORN BUTTON ASSEMBLY

Hide 5.REMOVE STEERING WHEEL ASSEMBLY

Hide 45024 6.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)

Hide 45024 7.REMOVE LOWER STEERING COLUMN COVER SUB-ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)

Hide 45286B 8.REMOVE UPPER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)

Hide 45286B 9.REMOVE UPPER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)

Hide 84650 10.REMOVE WINDSHIELD WIPER SWITCH ASSEMBLY

Hide 84329 11.REMOVE TURN SIGNAL SWITCH

Hide 58810J 12.REMOVE CONSOLE BOX ASSEMBLY

Hide 67914 13.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 14.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62312B 15.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.

Disconnect the front door opening trim weatherstrip LH.


Hide 62212 16.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Hide 62212 17.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Hide 55318C 18.REMOVE INSTRUMENT SIDE PANEL LH

a.
B482047C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B482048C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 2 claws and 4 clips as shown in the illustration.

NOTICE:

To prevent damage to the instrument side panel LH, do not insert the moulding remover in a position other than shown in the illustration.



c.
B482049C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 guides to remove the instrument side panel LH as shown in the illustration.


Hide 55606 19.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for LHD)

a.
B482050C01
0,0 0,0 false

Remove the 2 screws <C>.


b.
B482051C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 claws as shown in the illustration.


c.
B482052C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guide as shown in the illustration.


d.

Disconnect the connector.


e.
B482053

Disengage the 2 claws to disconnect the DLC3 connector.


f.

Disengage the 2 clamps to remove the No. 1 instrument panel under cover sub-assembly.


Hide 55606 20.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for RHD)

a.
B480744

Remove the 3 screws <C>.


b.
B480745C02
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws as shown in the illustration.


c.

Disconnect the connector.


d.
B480747

Disengage the 2 claws to disconnect the DLC3 connector.


e.

Disengage the clamp to remove the No. 1 instrument panel under cover sub-assembly.


Hide 55436B 21.REMOVE NO. 2 METER HOOD CLUSTER

a.
B469228C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 3 clips to remove the No. 2 meter hood cluster as shown in the illustration.


Hide 53601 22.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B469230

Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.


Hide 55302D 23.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

a.
B482060C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 8 clips as shown in the illustration.


b.

Disengage the clamp.


c.

Disconnect each connector to remove the No. 1 instrument panel sub-assembly.


Hide 55302D 24.REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY (w/ Driver Side Knee Airbag)

a.
B482054C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 6 clips as shown in the illustration.


b.

Disengage the clamp.


c.

Disconnect each connector to remove the No. 1 instrument panel sub-assembly.


Hide 73900 25.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

Hide 55410C 26.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B469233

Remove the 2 clips.


b.
B469234C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration.


c.
B482062C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration.


d.
B482063C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides as shown in the illustration.


e.

Disconnect the connector to remove the instrument cluster finish panel assembly.


Hide 83100 27.REMOVE COMBINATION METER ASSEMBLY

Hide 55480D 28.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.
B469238C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 5 clips to remove the lower instrument panel finish panel assembly as shown in the illustration.


b.

w/ Switch:

i.

Disconnect the connector.



Hide 55670 29.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

Disengage the 8 clips in the order shown in the illustration.

B482064C01
4.979,1.302 5.135,1.5 0.156,0.198 10 true 1 4.719,0.76 4.875,0.958 0.156,0.198 10 true 2 3.865,1.438 4.021,1.635 0.156,0.198 10 true 3 3.781,0.656 3.938,0.854 0.156,0.198 10 true 4 3.26,1.219 3.417,1.417 0.156,0.198 10 true 5 3.115,0.531 3.271,0.729 0.156,0.198 10 true 6 2.792,1.135 2.948,1.333 0.156,0.198 10 true 7 2.604,0.5 2.76,0.698 0.156,0.198 10 true 8
V113146

Place Hand Here
V113147

Remove in this Direction



b.

Disengage the 3 clips in the order shown in the illustration.

B482065C01
3.115,1.188 3.271,1.385 0.156,0.198 10 true 1 2.698,1.51 2.854,1.708 0.156,0.198 10 true 2 2.427,1.688 2.583,1.885 0.156,0.198 10 true 3
V113146

Place Hand Here
V113147

Remove in this Direction



c.

Disconnect the connector to remove the No. 3 instrument panel register assembly.


Hide 55900 30.REMOVE AIR CONDITIONING CONTROL ASSEMBLY (except 8 Inch Display)

Hide 55423B 31.REMOVE INSTRUMENT CLUSTER FINISH PANEL COVER (w/o Radio Receiver)

a.

for RHD:

i.

Disengage the 4 clips to remove the instrument cluster finish panel cover as shown in the illustration.

B482234C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction




Hide 55420A 32.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Radio Receiver)

a.

Disengage the 4 clips in the order shown in the illustration.

B482068C02
6.531,2.563 6.688,2.76 0.156,0.198 10 true 1 5.604,2.573 5.76,2.771 0.156,0.198 10 true 2 4.615,2.552 4.771,2.75 0.156,0.198 10 true 3 3.708,3.156 3.865,3.354 0.156,0.198 10 true 4
V113146

Place Hand Here
V113147

Remove in this Direction



b.

Disengage the 5 clips as shown in the illustration.

B482069C02
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction



c.

Disconnect the connector to remove the center instrument cluster finish panel assembly.


Hide 33.REMOVE RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)

a.
B482072

Remove the 4 bolts <B>.


b.

Disconnect the connector to remove the radio tuner opening cover with bracket.


Hide 34.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for 7 Inch Display)

Hide 35.REMOVE RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for 8 Inch Display)

Hide 67913 36.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62111A 37.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62311B 38.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62211 39.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 55317A 40.REMOVE INSTRUMENT SIDE PANEL RH

a.
B469243C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B469244C01
0,0 0,0 false
V113147

Remove in this Direction


Using a moulding remover, disengage the 2 claws and 4 clips as shown in the illustration.

NOTICE:

To prevent damage to the instrument side panel RH, do not insert the moulding remover in a position other than shown in the illustration.



c.
B469246C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.


Hide 55607 41.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B469248C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws as shown in the illustration.


b.
B469250C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides as shown in the illustration.


c.

Disengage the clamp.


d.

Disconnect the connector to remove the No. 2 instrument panel under cover sub-assembly.


Hide 73990 42.REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

Hide 55303B 43.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Passenger Side Knee Airbag)

a.
B482074C01
1.313,0.302 1.552,0.458 0.24,0.156 10 true *a 2.615,1.885 2.865,2.063 0.25,0.177 10 true *b 0.563,0.594 0.802,0.75 0.24,0.156 10 true *a 0.25,1.375 0.49,1.531 0.24,0.156 10 true *a 0.771,1.781 1.021,1.958 0.25,0.177 10 true *b
*a Screws <C>
*b Bolts <D>


Remove the 3 screws <C>.


b.

Remove the 2 bolts <D>.


c.
B482075C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws as shown in the illustration.


d.

Disconnect the connector to remove the lower instrument panel sub-assembly.


Hide 55303B 44.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/ Passenger Side Knee Airbag)

a.
B469252

Remove the 5 screws <C>.


b.
B469253C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 4 claws as shown in the illustration.


c.

Disconnect the connector to remove the lower instrument panel sub-assembly.


Hide 55472C 45.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL

a.
B469255C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration.


b.
B469256C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the No. 1 instrument panel speaker panel as shown in the illustration.


Hide 86160P 46.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

Hide 55473B 47.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL

a.
B469259C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips as shown in the illustration.


b.
B469260C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 guides to remove the No. 2 instrument panel speaker panel as shown in the illustration.


Hide 86160P 48.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 55011A 49.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.
B469263C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 4 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.


Hide 55650 50.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B469265C01
0,0 0,0 false
V113146

Place Hand Here
V113147

Remove in this Direction


Disengage the 2 clips and 2 claws to remove the No. 1 instrument panel register assembly as shown in the illustration.


Hide 82149A 51.DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/o Occupant Classification System)

Hide 82149A 52.DISCONNECT NO. 5 INSTRUMENT PANEL WIRE (w/ Occupant Classification System)

Hide 53.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

a.

for Automatic Air Conditioning System:

i.
B469267C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the 2 claws to disconnect the cooler (room temp. sensor) thermistor as shown in the illustration.



b.

Disconnect each connector.

B482077C01
6.469,1.49 6.448,1.177 true 6.385,1.531 6.698,1.729 0.313,0.198 12 true *A 0.219,4.833 0.521,5.031 0.302,0.198 12 true *B 2.375,4.781 2.688,4.979 0.313,0.198 12 true *C
*A w/ Digital Audio Broadcasting Antenna or Television Antenna *B w/ Ion Generator
*C w/ Headup Display - -



c.

Disengage each clamp.


d.

Remove the 2 clips.

B482013C04
5.25,6.156 5.563,6.313 0.313,0.156 10 true *a 2.219,4.521 2.531,4.677 0.313,0.156 10 true *b 1.083,0.74 1.396,0.896 0.313,0.156 10 false *c 3.427,2.646 3.74,2.802 0.313,0.156 10 true *d 5.385,0.25 5.698,0.406 0.313,0.156 10 false *c 6.24,6.188 6.552,6.344 0.313,0.156 10 true *a 4.531,4.146 4.844,4.302 0.313,0.156 10 true *b 5.24,3.99 5.552,4.146 0.313,0.156 10 true *b 6.615,2.927 6.927,3.083 0.313,0.156 10 true *b
*a Bolt <A> *b Bolt <B>
*c Clip *d Nut <F>



e.

Remove the 4 bolts <B>, 2 bolts <A> and nut <F>.


f.

Disengage the 4 guides and remove the instrument panel safety pad sub-assembly as shown in the illustration.

B482014C02
0,0 0,0 false
V113147

Remove in this Direction - -


NOTICE:
·

Do not damage the instrument panel safety pad sub-assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.