Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) › from 2017.12
RM33A0E _58 Vehicle Interior _065387 HEATING / AIR CONDITIONING _0341905 AIR CONDITIONING SYSTEM(for Manual Air Conditioning System) C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Manual Air Conditioning System)  B14B2  Lost Communication with Front Panel LIN  


DESCRIPTION

The air conditioning control assembly communicates with the air conditioning amplifier assembly via LIN communication.

If a malfunction occurs in the LIN communication system, the air conditioning amplifier assembly will not operate, even if the air conditioning control assembly is operated.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory
B14B2 Lost Communication with Front Panel LIN Lost communication with air conditioning control assembly
·

Harness or connector

·

Air conditioning control assembly

·

Air conditioning amplifier assembly


Memorized
(10 sec. or more)*

*: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.


WIRING DIAGRAM

E282266E54
0.531,2.458 0.99,2.656 0.458,0.198 10 false K26 1.594,0.865 2.052,1.063 0.458,0.198 10 false LIN1 1.615,1.396 2.073,1.594 0.458,0.198 10 false IG+ 1.604,1.958 2.063,2.156 0.458,0.198 10 false GND 2.604,1.573 3.635,1.802 1.031,0.229 10 false ECU-IG1 NO. 4 3.885,1.427 4.833,1.792 0.948,0.365 10 false from IG1-NO. 1 Relay 5.271,0.896 5.729,1.094 0.458,0.198 10 false LIN1 4.813,2.469 5.271,2.667 0.458,0.198 10 false K54 0.531,2.656 2.646,2.927 2.115,0.271 10 false Air Conditioning Control Assembly 4.792,2.635 7.031,2.885 2.24,0.25 10 false Air Conditioning Amplifier Assembly 0.958,3.198 2.677,3.406 1.719,0.208 10 false : LIN Communication Line 2.031,0.719 2.49,0.917 0.458,0.198 10 false 9 2.031,1.292 2.49,1.49 0.458,0.198 10 false 2 2.042,1.781 2.5,1.979 0.458,0.198 10 false 6 4.979,0.719 5.438,0.917 0.458,0.198 10 false 14

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - IG POWER SOURCE)
a.

Disconnect the K26 air conditioning control assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K26-2 (IG+) - Body ground Ignition switch ON 11 to 14 V
K26-2 (IG+) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K26-6 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - AIR CONDITIONING AMPLIFIER ASSEMBLY)
a.

Disconnect the K54 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K26-9 (LIN1) - K54-14 (LIN1) Always Below 1 Ω
K26-9 (LIN1) or K54-14 (LIN1) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT AIR CONDITIONING AMPLIFIER ASSEMBLY
E334619N03
0.302,1.563 0.76,1.76 0.458,0.198 10 false GND

a.

Connect the K54 air conditioning amplifier assembly connector.


b.

Turn the ignition switch to ON.


c.

Using an oscilloscope, check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Terminal No. K54-14 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON


Result:
Proceed to
OK
NG



OK

5.INSPECT AIR CONDITIONING CONTROL ASSEMBLY

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

5.INSPECT AIR CONDITIONING CONTROL ASSEMBLY
E375602E01
1.49,0.25 1.958,0.51 0.469,0.26 2.792,2.281 2.604,2.281 2.604,2.281 2.271,1.385 true 0.219,0.229 0.594,0.469 0.375,0.24 10 false *a 0.333,3.917 0.792,4.115 0.458,0.198 10 false GND 1.583,0.302 2.042,0.5 0.458,0.198 10 false K26 2.833,2.188 3.292,2.385 0.458,0.198 10 false LIN1

a.

Connect the K26 air conditioning control assembly connector.


b.

Turn the ignition switch to ON.


c.

Using an oscilloscope, check the waveform.

OK:

Waveform is similar to that shown in the illustration.


Item Content
Terminal No. K26-9 (LIN1) - Body ground
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Ignition switch ON


Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING CONTROL ASSEMBLY