Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM (w/o Automatic Headlight Beam Level Control System) › from 2017.12
RM33A0E _59 Vehicle Exterior _065395 LIGHTING (EXT) _0341635 LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System) J

LIGHTING (EXT)  LIGHTING SYSTEM(w/o Automatic Headlight Beam Level Control System)  Rear Fog Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the rear fog light.

WIRING DIAGRAM

E371120E02
0.531,1.021 1.76,1.219 1.229,0.198 10 false from Battery 2.292,1.188 2.896,1.458 0.604,0.271 10 false ALT 3,1.042 3.25,1.271 0.25,0.229 10 false 3F 3.031,0.844 3.281,1.073 0.25,0.229 10 false 1 4.615,1.688 5,1.875 0.385,0.188 10 false TAIL 5.323,1.552 5.708,1.74 0.385,0.188 10 false TAIL 4.521,2.427 5.104,2.646 0.583,0.219 10 false FOG RR 4.49,3.729 5.073,3.948 0.583,0.219 10 false FOG RR 5.875,0.948 6.26,1.135 0.385,0.188 10 false 14 6.104,0.948 6.594,1.208 0.49,0.26 10 false TRLY 5.865,4 6.25,4.188 0.385,0.188 10 false 27 6.115,4 6.594,4.229 0.479,0.229 10 false RFGO 3.719,4.448 5.354,4.885 1.635,0.438 10 false Instrument Panel Junction Block Assembly 5.458,4.875 5.771,5.094 0.313,0.219 10 false MB 5.458,5 7.115,5.563 1.656,0.563 10 false Main Body ECU (Multiplex Network Body ECU) 2.354,2.938 2.604,3.167 0.25,0.229 10 false 3 3,2.865 3.25,3.094 0.25,0.229 10 false 21 1.458,3.25 2.24,3.448 0.781,0.198 10 false Fog Light 1.063,3.771 2.75,4.083 1.688,0.313 10 false Rear Light Assembly LH 2.156,2.958 2.406,3.188 0.25,0.229 10 false B 1.219,2.958 1.469,3.188 0.25,0.229 10 false E 1.052,3.625 1.427,3.854 0.375,0.229 10 false W15 2.99,3.063 3.24,3.292 0.25,0.229 10 false 3D 1.052,2.958 1.302,3.188 0.25,0.229 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*

*: w/ Smart Entry and Start System




PROCEDURE

1.CHECK OPERATION (TAILLIGHTS)
a.

Check the operation of the taillights.

OK:

Taillights operate normally.



Result:
Proceed to
OK
NG



OK

2.PERFORM ACTIVE TEST USING GTS

NG

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Rear Fog Light Relay Rear fog lights OFF or ON Light control switch in tail position
Body Electrical > Main Body > Active Test
Tester Display
Rear Fog Light Relay
50004 123 17
OK:

Rear fog light relay operates. (Rear fog lights come on.)



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
3.CHECK HARNESS AND CONNECTOR (REAR LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND BODY GROUND)
a.

Disconnect the W15 rear light assembly LH connector.


b.

Disconnect the 3D instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W15-3 (B) - 3D-21 Always Below 1 Ω
W15-3 (B) or 3D-21 - Body ground Always 10 kΩ or higher
W15-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
E345461C11
1.781,0.354 2.177,0.625 0.396,0.271 5.021,0.396 5.417,0.667 0.396,0.271 3.354,2.229 3.75,2.5 0.396,0.271 2.854,3.292 3.271,2.875 false 4.365,3.281 4.781,2.865 false 1.917,0.427 2.292,0.698 0.375,0.271 10 false 3F 5.146,0.469 5.521,0.74 0.375,0.271 10 false 3D 3.458,2.302 3.833,2.573 0.375,0.271 10 false MB 2.677,3.323 3.219,3.594 0.542,0.271 10 false TRLY 4.229,3.313 4.771,3.583 0.542,0.271 10 false RFGO 0.375,0.24 0.75,0.51 0.375,0.271 10 false *a
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


a.

Remove the instrument panel junction block assembly.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.


c.

Connect a positive (+) lead from the battery to terminal 3F-1.


d.

Connect a negative (-) lead from the battery to terminal MB-14 (TRLY) and MB-27 (RFGO).


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3D-21 - Battery negative (-) terminal Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY