There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
| Resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus lines ·
Short in CAN branch lines ·
Central gateway ECU (network gateway ECU) ·
Headlight ECU sub-assembly LH (w/ Automatic Headlight Beam Level Control System) ·
Headlight ECU sub-assembly RH (w/ Automatic Headlight Beam Level Control System) ·
Outer mirror control ECU assembly (for driver side) (w/ Seat Position Memory System) ·
Outer mirror control ECU assembly (for front passenger side) (w/ Seat Position Memory System) ·
Position control ECU assembly RH (w/ Seat Position Memory System) ·
Multiplex tilt and telescopic ECU (w/ Power Tilt and Power Telescopic System) ·
Air conditioning amplifier assembly ·
Certification ECU (smart key ECU assembly) (w/ Smart Entry and Start System) ·
Main body ECU (multiplex network body ECU) ·
Combination meter assembly ·
Meter mirror sub-assembly (w/ Headup Display System) ·
No. 3 CAN junction connector ·
No. 1 junction connector ·
No. 2 junction connector ·
No. 5 junction connector (for RHD) ·
No. 6 junction connector (for LHD) |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
Before replacing the main body ECU (multiplex network body ECU) or certification ECU (smart key ECU assembly), refer to Service Bulletin.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the K126 No. 3 CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to No. 1 Junction Connector |
| *c | to Certification ECU (Smart Key ECU Assembly)
(w/ Smart Entry and Start System) |
*d | to Combination Meter Assembly |
| *e | to Main Body ECU (Multiplex Network Body ECU) | *f | to Air Conditioning Amplifier Assembly |
| *g | to Headlight ECU Sub-assembly LH
(w/ Automatic Headlight Beam Level Control System) |
*h | to Meter Mirror Sub-assembly
(w/ Headup Display System) |
| *i | to Multiplex Tilt and Telescopic ECU
(w/ Power Tilt and Power Telescopic System) |
- | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| K126-3 (CANH) - K126-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 junction connector |
| K126-4 (CANH) - K126-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly)*1 |
| K126-5 (CANH) - K126-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| K126-6 (CANH) - K126-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| K126-7 (CANH) - K126-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| K126-8 (CANH) - K126-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Headlight ECU sub-assembly LH*2 |
| K126-9 (CANH) - K126-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Meter mirror sub-assembly*3 |
| K126-10 (CANH) - K126-21 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Multiplex tilt and telescopic ECU*4 |
*1: w/ Smart Entry and Start System
*2: w/ Automatic Headlight Beam Level Control System
*3: w/ Headup Display System
*4: w/ Power Tilt and Power Telescopic System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to combination meter assembly) | B |
| NG (Line to No. 1 junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Disconnect the K21 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 3 CAN Junction Connector) |
*b | to Combination Meter Assembly |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K126-5 (CANH) - K126-16 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect the K126 No. 3 CAN junction connector.
Disconnect the R94 No. 1 junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 1 Junction Connector) |
*b | to Outer Mirror Control ECU Assembly (for Front Passenger Side)
(w/ Seat Position Memory System) |
| *c | to No. 3 CAN Junction Connector | *d | to No. 5 Junction Connector
(for RHD) |
| *e | to No. 6 Junction Connector
(for LHD) |
- | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R94-1 (CANH) - R94-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Outer mirror control ECU assembly (for front passenger side)*1 |
| R94-3 (CANH) - R94-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 3 CAN junction connector |
| R94-4 (CANH) - R94-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 5 junction connector*2 |
| R94-4 (CANH) - R94-15 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 6 junction connector*3 |
*1: w/ Seat Position Memory System
*2: for RHD
*3: for LHD
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 3 CAN junction connector) | B |
| NG (Line to No. 5 junction connector (for RHD)) | C |
| NG (Line to No. 6 junction connector (for LHD)) | D |
| NG (Line to ECU or sensor) | E |
A
B
C
D
E
Reconnect the R94 No. 1 junction connector.
Disconnect the R100 No. 5 junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 5 Junction Connector) |
*b | to No. 2 Junction Connector |
| *c | to No. 1 Junction Connector | *d | to Position Control ECU Assembly RH
(w/ Seat Position Memory System) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R100-5 (CANH) - R100-16 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 junction connector |
| R100-6 (CANH) - R100-17 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 junction connector |
| R100-7 (CANH) - R100-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Position control ECU assembly RH* |
*: w/ Seat Position Memory System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 1 junction connector) | B |
| NG (Line to No. 2 junction connector) | C |
| NG (Line to ECU or sensor) | D |
A
B
C
D
Reconnect the R94 No. 1 junction connector.
Disconnect the R101 No. 6 junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 6 Junction Connector) |
*b | to No. 2 Junction Connector |
| *c | to No. 1 Junction Connector | - | - |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R101-1 (CANH) - R101-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 junction connector |
| R101-2 (CANH) - R101-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 1 junction connector |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 1 junction connector) | B |
| NG (Line to No. 2 junction connector) | C |
A
B
C
Reconnect the R100 No. 5 junction connector or R101 No. 6 junction connector.
Disconnect the R97 No. 2 junction connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 2 Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| *c | to No. 5 Junction Connector
(for RHD) |
*d | to No. 6 Junction Connector
(for LHD) |
| *e | to Outer Mirror Control ECU Assembly (for Driver Side)
(w/ Seat Position Memory System) |
*f | to Headlight ECU Sub-assembly RH
(w/ Automatic Headlight Beam Level Control System) |
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
| R97-1 (CANH) - R97-12 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Central gateway ECU (network gateway ECU) |
| R97-2 (CANH) - R97-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 5 junction connector*1 |
| R97-2 (CANH) - R97-13 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 6 junction connector*2 |
| R97-3 (CANH) - R97-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Outer mirror control ECU assembly (for driver side)*3 |
| R97-5 (CANH) - R97-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Headlight ECU sub-assembly RH*4 |
*1: for RHD
*2: for LHD
*3: w/ Seat Position Memory System
*4: w/ Automatic Headlight Beam Level Control System
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Line to No. 5 junction connector (for RHD)) | B |
| NG (Line to No. 6 junction connector (for LHD)) | C |
| NG (Line to central gateway ECU (network gateway ECU)) | D |
| NG (Line to ECU or sensor) | E |
A
B
C
D
E
Disconnect the K76 central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| *a | Front view of wire harness connector
(to No. 2 Junction Connector) |
*b | to Central Gateway ECU (Network Gateway ECU) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| R97-1 (CANH) - R97-12 (CANL) | Cable disconnected from negative (-) battery terminal | 1 MΩ or higher |
| Result |
|---|
| OK |
| NG |
OK
NG
Reconnect all wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU
| *a | Component with harness connected
(Central Gateway ECU (Network Gateway ECU)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K76-15 (CA5H) - K76-16 (CA5L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.
| Result |
|---|
| OK |
| NG |
OK
NG