Home › Engine / Hybrid System › 2GR-FKS (INTAKE / EXHAUST) › INTAKE MANIFOLD › 2017.12–2018.04
RM33A0E _51 Engine / Hybrid System _065336 2GR-FKS INTAKE / EXHAUST _0328626 INTAKE MANIFOLD A

2GR-FKS INTAKE / EXHAUST  INTAKE MANIFOLD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during intake manifold removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 55708 4.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53607A 5.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for LHD)

Hide 53607A 6.REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY (for RHD)

Hide 22030 7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 11209 8.REMOVE V-BANK COVER SUB-ASSEMBLY

Hide 12261 9.DISCONNECT VENTILATION HOSE

a.
A408126

Slide the clip and disconnect the ventilation hose from the intake air surge tank assembly.


Hide 25860 10.DISCONNECT PURGE VALVE (PURGE VSV)

a.
A412397

Disconnect the No. 1 fuel vapor feed hose from the intake air surge tank assembly.


b.

Remove the bolt and disconnect the purge valve (purge VSV) from the intake air surge tank assembly.


Hide 17126 11.REMOVE NO. 2 SURGE TANK STAY

a.
A408128

Remove the 2 bolts and No. 2 surge tank stay from the intake air surge tank assembly and camshaft housing RH.


Hide 17190 12.REMOVE INTAKE AIR SURGE TANK ASSEMBLY

a.
A408129

Disconnect the vacuum switching valve (for ACIS) connector.


b.

Disconnect the vacuum hose sub-assembly from the vacuum switching valve (for ACIS).


c.

Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.


d.
A415509C01
2.354,1.104 2.635,1.281 2.635,1.281 2.635,1.542 true 1.875,1.802 1.875,1.354 true 1.271,1.75 1.271,1.104 true 1.885,4.104 1.885,3.656 true 2.323,3.438 2.604,3.615 2.604,3.615 2.604,3.875 true 1.26,4.073 1.26,3.427 true 0.021,0.052 0.354,0.302 0.333,0.25 12 true *A 0.01,2.417 0.313,2.635 0.302,0.219 12 true *B 2.563,1.573 2.771,1.781 0.208,0.208 10 true *1 1.198,1.781 1.396,1.969 0.198,0.188 10 true *2 1.792,1.833 2.01,2.042 0.219,0.208 10 true *3 1.802,4.135 2.021,4.344 0.219,0.208 10 true *3 2.51,3.906 2.719,4.115 0.208,0.208 10 true *1 1.188,4.083 1.385,4.271 0.198,0.188 10 true *2
*A for LHD
*B for RHD
*1 Vacuum Hose Sub-assembly
*2 Vacuum Hose
*3 No. 2 Air Tube


Disengage the 2 clamps to disconnect the vacuum hose sub-assembly from the intake air surge tank assembly.


e.

Disengage the clamp to disconnect the vacuum hose from the intake air surge tank assembly.


f.

Disengage the clamp to disconnect the No. 2 air tube from the intake air surge tank assembly.


g.
A408131C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 5 bolts, 2 nuts and intake air surge tank assembly from the intake manifold.


h.

Remove the plug from the intake air surge tank assembly.


Hide 17176 13.REMOVE AIR SURGE TANK TO INTAKE MANIFOLD GASKET

a.
A370410

Remove the air surge tank to intake manifold gasket from the intake air surge tank assembly.


Hide 11254 14.REMOVE NO. 1 V-BANK COVER BRACKET

HINT:

Perform this procedure only when replacement of the No. 1 V-bank cover bracket is necessary.


a.
A370409

Remove the 2 No. 1 V-bank cover brackets from the intake air surge tank assembly.


Hide 12327A 15.REMOVE NO. 2 ENGINE MOUNTING STAY RH

a.
A408132

Remove the bolt and disconnect the wire harness clamp from the wire harness clamp bracket.


b.
A408133

Remove the bolt and separate the wire harness clamp bracket from the No. 2 engine mounting stay RH.


c.
A408135C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the bolt, 2 nuts and No. 2 engine mounting stay RH from the engine mounting insulator sub-assembly RH.


d.
A408134

Remove the bolt and No. 2 engine mounting stay RH from the intake manifold and front No. 1 engine mounting bracket LH.


Hide 23800 17.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

Hide 23807V 18.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23291 19.REMOVE INJECTOR VIBRATION INSULATOR

Hide 17111 20.REMOVE INTAKE MANIFOLD

a.
A408136C01
0,0 0,0 false
V100135

Bolt
V100136

Nut


Remove the 4 bolts, 4 nuts and intake manifold from the cylinder head sub-assembly.


Hide 17177 21.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET

a.
A408137

Remove the 2 No. 1 intake manifold to head gaskets from each cylinder head sub-assembly.


Hide 22.REMOVE STUD BOLT

HINT:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A370417

Using an E8 "TORX" socket wrench, remove the 2 stud bolts from the intake manifold.