This DTC is stored when LIN communication between the sliding roof ECU (sliding roof drive gear assembly)*1 or sliding roof ECU (sliding roof drive gear sub-assembly)*2 and main body ECU (multiplex network body ECU) stops for 10 seconds or more.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1273 | Sliding Roof ECU Communication Stop | No communication between sliding roof ECU (sliding roof drive gear assembly)*1 or sliding roof ECU (sliding roof drive gear sub-assembly)*2 and main body ECU (multiplex network body ECU) for 10 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Sliding roof ECU (sliding roof drive gear assembly)*1 ·
Sliding roof ECU (sliding roof drive gear sub-assembly)*2 ·
Wire harness or connector ·
S/ROOF fuse |
*1: w/ Panoramic Moon Roof System
*2: w/ Sliding Roof System
Inspect the fuses for circuits related to this system before performing the following procedure.
When the sliding roof ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*1
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*2
See pageXXX
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*3
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*4
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*1: w/ Panoramic Moon Roof System
*2: w/ Sliding Roof System
*3: w/ Smart Entry and Start System
*4: w/ Door Control Battery
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-17 - MB-16 (LIN2) | Always | Below 1 Ω |
| Result | Proceed to |
|---|---|
| OK (w/ Panoramic Moon Roof System) | A |
| OK (w/ Sliding Roof System) | B |
| NG | C |
A
B
C
Disconnect the q1 sliding roof ECU (sliding roof drive gear assembly) connector.
Measure the resistance according to the value(s) in the table below.
Make sure that each ECU is in sleep mode before performing the inspection. To enter sleep mode, turn the ignition switch from ON to off and wait for 180 seconds or more without operating any switches.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-17 - q1-7 (LIN) | Ignition switch off | Below 1 Ω |
| 3B-17 or q1-7 (LIN) - Body ground | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| q1-1 (+B) - q1-2 (E) | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| q1-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the sliding roof ECU (sliding roof drive gear assembly).
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B1273 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the V19 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-17 - V19-7 (MPX1) | Ignition switch off | Below 1 Ω |
| V19-7 (MPX1) or 3B-17 - Body ground | Ignition switch off | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V19-1 (B) - V19-2 (E) | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V19-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the sliding roof ECU (sliding roof drive gear sub-assembly).
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING(for Moon Roof)>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs.
DTC B1273 is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG