If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B2325 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B2325 | LIN Communication Bus Malfunction | The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Instrument panel junction block assembly ·
Multiplex network master switch assembly ·
Power window regulator motor assembly (driver door) ·
Power window regulator motor assembly (front passenger door) ·
Power window regulator motor assembly (rear LH door) ·
Power window regulator motor assembly (rear RH door) ·
Sliding roof ECU (sliding roof drive gear assembly)*1 ·
Roof sunshade ECU (sliding roof drive gear assembly)*1 ·
Sliding roof ECU (sliding roof drive gear sub-assembly)*2 ·
Wire harness or connector |
*1: w/ Panoramic Moon Roof System
*2: w/ Sliding Roof System
When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
When the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*1
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>PANORAMIC MOON ROOF SYSTEM>INITIALIZATION
When the sliding roof ECU (sliding roof drive gear sub-assembly) is replaced or removed and reinstalled, it is necessary to perform initialization.*2
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF SYSTEM>INITIALIZATION
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.*3
The vehicle battery supplies power to the main body ECU (multiplex network body ECU) via the door control battery. Therefore, before performing this troubleshooting procedure, make sure to perform an on-vehicle inspection to confirm that the main body ECU (multiplex network body ECU) power source circuit is normal.*4
Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>ON-VEHICLE INSPECTION
*1: w/ Panoramic Moon Roof System
*2: w/ Sliding Roof System
*3: w/ Smart Entry and Start System
*4: w/ Door Control Battery
Disconnect the O6*1 or N7*2 power window regulator motor assembly (driver door) connector.
*1: for LHD
*2: for RHD
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Disconnect the O2*1 or N2*2 multiplex network master switch assembly connector.
*1: for LHD
*2: for RHD
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Disconnect the N7*1 or O6*2 power window regulator motor assembly (front passenger door) connector.
*1: for LHD
*2: for RHD
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Disconnect the P6 power window regulator motor assembly (rear RH door) connector.
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Disconnect the Q6 power window regulator motor assembly (rear LH door) connector.
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output (w/ Panoramic Moon Roof System) | A |
| DTC B2325 is output (w/ Sliding Roof System) | B |
| DTC B2325 is output (w/o Panoramic Moon Roof System and Sliding Roof System) | C |
| DTC B2325 is not output | D |
A
B
C
D
Disconnect the q1 sliding roof ECU (sliding roof drive gear assembly) connector.
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Disconnect the q2 roof sunshade ECU (sliding roof drive gear assembly) connector.
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Disconnect the 3D instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-25 - Body ground | Always | 10 kΩ or higher |
Disconnect all other connectors in the same circuit.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-25 - Other terminals | Always | 10 kΩ or higher |
| Result | Proceed to |
|---|---|
| OK (w/ Panoramic Moon Roof System or Sliding Roof System) | A |
| OK (w/o Panoramic Moon Roof System and Sliding Roof System) | B |
| NG | C |
A
B
C
Disconnect the 3B instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3B-17 - Body ground | Always | 10 kΩ or higher |
| 3B-17 - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL
Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
Measure the resistance according to the value(s) in the table below.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3D-25 - 3B-3 | Always | 10 kΩ or higher |
| MB-16 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Install the main body ECU (multiplex network body ECU) to the instrument panel junction block assembly.
Connect all instrument panel junction block assembly connectors other than 3B and 3D.
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
*b | Waveform 1 |
Using a GTS, check the waveform.
This inspection is to check the LIN communication line in the instrument panel junction block assembly that connects the wire harness to the built-in main body ECU (multiplex network body ECU).
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| 3D-25 - Body ground | Ignition switch ON | 2 V/DIV., 200 ms/DIV. | Pulse generation
(See waveform 1) |
| 3B-17 - Body ground* | Ignition switch ON | 2 V/DIV., 200 ms/DIV. | Pulse generation
(See waveform 1) |
*: w/ Panoramic Moon Roof System or Sliding Roof System
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Disconnect the V19 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
Clear the DTCs.
After 10 seconds have elapsed, check if the same DTC is output again.
| Result | Proceed to |
|---|---|
| DTC B2325 is output | A |
| DTC B2325 is not output | B |
A
B
Click hereVehicle Exterior>SLIDING ROOF / CONVERTIBLE>SLIDING ROOF HOUSING(for Moon Roof)>DISASSEMBLY
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O2-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| O2-16 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N2-16 (LIN2) - Body ground | Always | 10 kΩ or higher |
| N2-16 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG