Home › Power Source / Network › NETWORKING › LIN COMMUNICATION SYSTEM › 2017.12–2021.08
RM33A0E _57 Power Source / Network _065377 NETWORKING _0323332 LIN COMMUNICATION SYSTEM U

NETWORKING  LIN COMMUNICATION SYSTEM  TERMINALS OF ECU  


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


B472410C11
1.125,3.25 1.563,3.5 0.438,0.25 3.156,3.219 3.594,3.469 0.438,0.25 5.448,3.208 5.885,3.458 0.438,0.25 1.698,4.573 2.135,4.823 0.438,0.25 5.385,4.573 5.823,4.823 0.438,0.25 1.104,6.167 1.542,6.417 0.438,0.25 3.667,6.125 4.104,6.375 0.438,0.25 6.313,6.198 6.75,6.448 0.438,0.25 3.365,7.646 3.802,7.896 0.438,0.25 5.292,6.094 5.729,6.344 0.438,0.25 5.292,6.406 5.729,6.656 0.438,0.25 1.656,1.208 1.958,1.208 false 1.667,1.552 1.969,1.552 false 1.667,1.875 1.969,1.875 false 4.042,0.792 4.042,0.313 4.042,0.313 4.229,0.313 false 0.552,2.563 0.552,2.344 0.552,2.344 0.854,2.344 false 3.469,7.698 3.781,7.896 0.313,0.198 10 false MB 4.292,0.24 4.604,0.438 0.313,0.198 10 false MB 2.042,1.135 2.354,1.333 0.313,0.198 10 false K51 2.052,1.479 2.365,1.677 0.313,0.198 10 false K52 2.052,1.802 2.365,2 0.313,0.198 10 false K53 0.875,1.083 1.188,1.281 0.313,0.198 10 false 3D 0.875,1.667 1.188,1.865 0.313,0.198 10 false 3C 0.885,2.031 1.198,2.229 0.313,0.198 10 false 3E 5.854,1.146 6.167,1.344 0.313,0.198 10 false 3B 5.854,1.76 6.167,1.958 0.313,0.198 10 false 3A 1.229,3.302 1.542,3.5 0.313,0.198 10 false K53 3.271,3.271 3.583,3.469 0.313,0.198 10 false K52 5.542,3.26 5.854,3.458 0.313,0.198 10 false K51 1.833,4.625 2.146,4.823 0.313,0.198 10 false 3A 1.24,6.219 1.552,6.417 0.313,0.198 10 false 3C 3.813,6.177 4.125,6.375 0.313,0.198 10 false 3D 6.438,6.24 6.75,6.438 0.313,0.198 10 false 3E 5.427,6.146 5.74,6.344 0.313,0.198 10 false 3F 5.51,4.625 5.823,4.823 0.313,0.198 10 false 3B 0.531,2.625 1.042,2.969 0.51,0.344 12 false *A 0.354,2.635 0.667,2.833 0.313,0.198 10 false 3F 0.354,2.833 0.667,3.031 0.313,0.198 10 false 3G 0.542,2.823 1.052,3.167 0.51,0.344 12 false *B 5.427,6.458 5.74,6.656 0.313,0.198 10 false 3G 5.76,6.125 6.271,6.469 0.51,0.344 12 false *A 5.76,6.427 6.271,6.771 0.51,0.344 12 false *B
*A for LHD *B for RHD


a.

Disconnect the MB main body ECU (multiplex network body ECU) connector.

Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connectors disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
MB-11 (GND1) - Body ground - Ground Always Below 1 Ω
MB-31 (BECU) - Body ground - Battery power supply Always 11 to 14 V
MB-30 (ACC) - Body ground - ACC power supply Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
MB-32 (IG) - Body ground - IG power supply Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V


c.

Reconnect the MB main body ECU (multiplex network body ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
3D-25 - Body ground LA-BE - Body ground LIN communication line Ignition switch ON Pulse generation
3B-17 - Body ground* L - Body ground LIN communication line Ignition switch ON Pulse generation

*: w/ Panoramic Moon Roof System or Sliding Roof System




CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (DRIVER DOOR)


B286202C35
2.031,0.583 2.448,0.833 0.417,0.25 2.031,0.885 2.448,1.135 0.417,0.25 2.146,0.625 2.469,0.833 0.323,0.208 10 false O6 2.51,0.604 2.833,0.813 0.323,0.208 12 false *A 2.51,0.906 2.833,1.115 0.323,0.208 12 false *B 2.156,0.927 2.479,1.135 0.323,0.208 10 false N7
*A for LHD *B for RHD


a.

Disconnect the O6*1 or N7*2 power window regulator motor assembly (driver door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-2 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
O6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-2 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
N7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the O6*1 or N7*2 power window regulator motor assembly (driver door) connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-9 (LIN) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-9 (LIN) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (FRONT PASSENGER DOOR)


B286202C33
2.031,0.583 2.448,0.833 0.417,0.25 2.031,0.885 2.448,1.135 0.417,0.25 2.146,0.625 2.469,0.833 0.323,0.208 10 false N7 2.51,0.604 2.833,0.813 0.323,0.208 12 false *A 2.51,0.906 2.833,1.115 0.323,0.208 12 false *B 2.156,0.927 2.479,1.135 0.323,0.208 10 false O6
*A for LHD *B for RHD


a.

Disconnect the N7*1 or O6*2 power window regulator motor assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-2 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
N7-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-2 (B) - Body ground GR - Body ground Battery power supply Always 11 to 14 V
O6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the N7*1 or O6*2 power window regulator motor assembly (front passenger door) connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N7-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O6-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR RH DOOR)


B203471N47
2.167,0.698 2.583,0.948 0.417,0.25 2.281,0.729 2.615,0.917 0.333,0.188 10 false P6

a.

Disconnect the P6 power window regulator motor assembly (rear RH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P6-2 (B) - Body ground B - Body ground Battery power supply Always 11 to 14 V
P6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the P6 power window regulator motor assembly (rear RH door) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
P6-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK POWER WINDOW REGULATOR MOTOR ASSEMBLY (REAR LH DOOR)


B203471N48
2.167,0.75 2.583,1 0.417,0.25 2.281,0.802 2.563,0.99 0.281,0.188 10 false Q6

a.

Disconnect the Q6 power window regulator motor assembly (rear LH door) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q6-2 (B) - Body ground B - Body ground Battery power supply Always 11 to 14 V
Q6-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the Q6 power window regulator motor assembly (rear LH door) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
Q6-9 (LIN) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY


B131578C17
2.979,0.25 3.396,0.5 0.417,0.25 3.75,0.25 4.167,0.5 0.417,0.25 3.094,0.302 3.406,0.49 0.313,0.188 10 false O2 3.854,0.302 4.167,0.49 0.313,0.188 10 false N2 3.438,0.281 3.75,0.469 0.313,0.188 12 false *A 4.198,0.281 4.51,0.469 0.313,0.188 12 false *B
*A for LHD *B for RHD


a.

Disconnect the O2*1 or N2*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-11 (B) - Body ground LA-R - Body ground Battery power supply Always 11 to 14 V
O2-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-11 (B) - Body ground LA-R - Body ground Battery power supply Always 11 to 14 V
N2-12 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the O2*1 or N2*2 multiplex network master switch assembly connector.

*1: for LHD

*2: for RHD



d.

Check for pulses according to the value(s) in the table below.

for LHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
O2-17 (LIN1) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation
O2-16 (LIN2) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation

for RHD
Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
N2-17 (LIN1) - Body ground P - Body ground LIN communication line Ignition switch ON Pulse generation
N2-16 (LIN2) - Body ground G - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) (w/ Panoramic Moon Roof System)


B417851N30
3.333,0.083 3.75,0.333 0.417,0.25 3.479,0.135 3.792,0.333 0.313,0.198 10 false q1

a.

Disconnect the q1 sliding roof ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
q1-1 (+B) - Body ground L - Body ground Battery power supply Always 11 to 14 V
q1-2 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the q1 sliding roof ECU (sliding roof drive gear assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
q1-7 (LIN) - Body ground B - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) (w/ Panoramic Moon Roof System)


B417851N29
3.333,0.083 3.75,0.333 0.417,0.25 3.469,0.125 3.781,0.323 0.313,0.198 10 false q2

a.

Disconnect the q2 roof sunshade ECU (sliding roof drive gear assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
q2-1 (+B) - Body ground G - Body ground Battery power supply Always 11 to 14 V
q2-2 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the q2 roof sunshade ECU (sliding roof drive gear assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
q2-7 (LIN) - Body ground B - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) (w/ Sliding Roof System)


B417851N47
3.333,0.083 3.75,0.333 0.417,0.25 3.427,0.135 3.74,0.333 0.313,0.198 10 false V19

a.

Disconnect the V19 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V19-1 (B) - Body ground B - Body ground Battery power supply Always 11 to 14 V
V19-2 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the V19 sliding roof ECU (sliding roof drive gear sub-assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
V19-7 (MPX1) - Body ground LA-P - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Smart Entry and Start System)


B416786N70
2,0.417 2.417,0.667 0.417,0.25 3.26,0.406 3.677,0.656 0.417,0.25 4.5,0.417 4.917,0.667 0.417,0.25 2.083,0.458 2.396,0.656 0.313,0.198 10 false A13 3.375,0.448 3.688,0.646 0.313,0.198 10 false R8 4.573,0.458 4.885,0.656 0.313,0.198 10 false K62

a.

Disconnect the K62 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K62-4 (+B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
K62-18 (E) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K62 certification ECU (smart key ECU assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K62-13 (LIN) - Body ground B - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR OR UPPER BRACKET ASSEMBLY) (w/ Smart Entry and Start System)


B439652N03
3.417,0.313 3.833,0.563 0.417,0.25 3.5,0.354 3.813,0.552 0.313,0.198 10 false K65

a.

Disconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K65-7 (B) - Body ground W - Body ground Battery power supply Always 11 to 14 V
K65-1 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω


c.

Reconnect the K65 steering lock ECU (steering lock actuator or upper bracket assembly) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K65-5 (LIN) - Body ground B - Body ground LIN communication line Ignition switch ON Pulse generation



CHECK ID CODE BOX (IMMOBILISER CODE ECU) (w/ ID Code Box)


B463193N04
3.344,0.146 3.792,0.417 0.448,0.271 3.406,0.198 4.021,0.396 0.615,0.198 10 false K139

a.

Disconnect the K139 ID code box (immobiliser code ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K139-5 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
K139-1 (+B) - Body ground LA-GR - Body ground +B power supply Always 11 to 14 V


c.

Reconnect the K139 ID code box (immobiliser code ECU) connector.


d.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
K139-2 (LIN1) - Body ground GR - Body ground LIN communication line Ignition switch ON Pulse generation