Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › 2017.12–2019.10
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P019515  Engine Oil Temperature Sensor Circuit Short to Battery or Open  


DESCRIPTION

Refer to DTC P019511.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>SFI SYSTEM (w/o Canister Pump Module)>P019511

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P019515 Engine Oil Temperature Sensor Circuit Short to Battery or Open The engine oil temperature sensor output voltage is higher than 4.94 V for 5 seconds or more (1 trip detection logic).
·

Open or short in engine oil temperature sensor circuit

·

Engine oil temperature sensor

·

ECM


Does not come on DTC stored SAE Code: P0198

HINT:

When this DTC is output, check the engine oil temperature in the Data List. Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor.

DTC No. Engine Oil Temperature Sensor Malfunction
P019515 -40°C (-40°F)
·

Short to +B in THEO circuit

·

Open in THEO circuit

·

Open in ETHE circuit



If the Data List values is normal it may be due to a temporary recovery from the malfunction condition. Check for intermittent problems.


MONITOR DESCRIPTION

The ECM monitors the engine oil temperature sensor and uses the sensor voltage to calculate the engine oil temperature. If the engine oil temperature sensor output voltage deviates from the normal operating range, the ECM determines that the engine oil temperature sensor circuit is malfunctioning and stores this DTC.

Example:

If the engine oil temperature sensor output voltage is higher than 4.94 V for 5 seconds or more, the ECM will store this DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON.

7.

Turn the GTS on.

8.

Start the engine and wait for the time indicated below [A].

-

If the engine oil temperature sensor is higher than -27°C (-17°F): 15 seconds or more.

-

If the engine oil temperature sensor is -27°C (-17°F) or less: 13 minutes or more.


9.

Enter the following menus: Powertrain / Engine / Trouble Codes [B].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

12.

Input the DTC: P019515.

13.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [A] through [B] again.




CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
A403508C01
4.781,1.448 5.188,1.74 0.406,0.292 1.24,2.063 1.646,2.302 0.406,0.24 10 false *1 3.667,2.052 4.01,2.313 0.344,0.26 10 false *2 3.396,1.208 3.969,1.438 0.573,0.229 10 false THEO 3.396,1.781 3.969,2.083 0.573,0.302 10 false ETHE 4.875,1.5 5.292,1.76 0.417,0.26 10 false C83 5.167,0.542 5.5,0.823 0.333,0.281 10 false *a 1.51,0.969 2.083,1.198 0.573,0.229 10 false THEO 1.698,1.417 2.271,1.646 0.573,0.229 10 false E2
*1 Engine Oil Temperature Sensor *2 ECM
*a Front view of wire harness connector
(to Engine Oil Temperature Sensor)
- -


a.

Disconnect the engine oil temperature sensor connector.


b.

Connect terminals 1 and 2 of the engine oil temperature sensor connector on the wire harness side.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / Engine / Data List / Engine Oil Temperature Sensor.

Powertrain > Engine > Data List
Tester Display
Engine Oil Temperature Sensor
50003 372 261

g.

According to the display on the GTS, read the Data List.

OK:
GTS Display Specified Condition
Engine Oil Temperature Sensor Higher than 168°C (334°F)



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (ENGINE OIL TEMPERATURE SENSOR - ECM)
a.

Disconnect the engine oil temperature sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C83-1 (THEO) - C57-123 (THEO) Always Below 1 Ω
C83-2 (E2) - C57-104 (ETHE) Always Below 1 Ω
C83-1 (THEO) or C57-123 (THEO) - Other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR