Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2017.12
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) C

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  P059712  Thermostat Heater Control Circuit Short to Battery  


DESCRIPTION

An electric heater is equipped to the temperature sensing portion of the thermostat. During normal driving, current does not flow to the heater and the thermostat functions as an ordinary thermostat. When the temperature of the engine increases by a large amount such as during high-load driving, control is performed to warm the heater of the temperature sensing portion, forcing the valve to open and causing a large amount of coolant to flow from the radiator.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P059712 Thermostat Heater Control Circuit Short to Battery Short in thermostat heater circuit and power supply circuit (1 trip detection logic).
·

Short in thermostat heater circuit

·

ECM


Comes on DTC stored SAE Code: P0599

Related Data List
DTC No. Data List
P059712 Coolant Temperature

MONITOR DESCRIPTION

The ECM monitors the output voltage while the thermostat heater is operating.

The thermostat heater turns on and off according to ON/OFF switching of a transistor inside the ECM.

If a continuous mismatch occurs between the ECM transistor state and the output voltage, the ECM determines there is a malfunction in the thermostat heater circuit and stores a DTC.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A232052E66
0.438,0.031 3.625,0.333 3.188,0.302 10 false Engine Coolant Temperature: 90°C or higher 0.792,0.479 1.844,0.75 1.052,0.271 10 false Calculate Load 1.479,0.875 1.844,1.094 0.365,0.219 10 false 45% 1.417,2.031 1.833,2.281 0.417,0.25 10 false Idling 0.677,2.375 2.125,2.646 1.448,0.271 10 false Ignition Switch ON 2.938,1.854 3.198,2.094 0.26,0.24 10 false [A] 4.813,0.406 5.115,0.635 0.302,0.229 10 false [B] 6.229,3.229 6.531,3.479 0.302,0.25 10 false [C] 4.229,3 5.531,3.281 1.302,0.281 10 false 3 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].

7.

Turn the GTS on.

8.

Enter the following menus: Powertrain / Engine / Data List / Calculate Load and Coolant Temperature.

9.

Drive the vehicle for at least 3 seconds at the Calculate Load of 45% or more and the Coolant Temperature of 90°C (194°F) or higher [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Stop the vehicle.

11.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

12.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P059712.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions



HINT:
·

If the judgment result is NORMAL, the system is normal.

·

If the judgment result is ABNORMAL, the system has a malfunction.

·

If the judgment result is INCOMPLETE, perform steps [B] through [C] again.




WIRING DIAGRAM

A404949E06
0.625,3.813 1.698,4.01 1.073,0.198 10 false Battery 0.49,3.125 1.333,3.438 0.844,0.313 10 false FL MAIN 0.448,2.781 1.708,3.115 1.26,0.333 10 false EFI-MAIN NO. 1 1.531,3.385 2.719,3.708 1.188,0.323 10 false EFI-MAIN NO. 1 1.604,2.479 1.76,2.677 0.156,0.198 10 false 3 2.292,2.458 2.448,2.656 0.156,0.198 10 false 5 1.615,3 1.771,3.198 0.156,0.198 10 false 1 2.302,2.979 2.458,3.177 0.156,0.198 10 false 2 6.01,4.198 6.469,4.396 0.458,0.198 10 false ECM 5.313,3.083 5.771,3.281 0.458,0.198 10 false A24 5.344,2.865 5.656,3.063 0.313,0.198 10 false 15 5.667,2.99 6.281,3.188 0.615,0.198 10 false MREL 0.51,1.646 1.156,2.042 0.646,0.396 10 false EFI-MAIN NO. 2 1.563,1.969 2.927,2.25 1.365,0.281 10 false EFI-MAIN NO. 2 1.552,1.073 1.708,1.271 0.156,0.198 10 false 3 2.26,1.052 2.417,1.25 0.156,0.198 10 false 5 1.573,1.563 1.729,1.76 0.156,0.198 10 false 1 2.26,1.563 2.417,1.76 0.156,0.198 10 false 2 2.365,1.354 3.406,1.729 1.042,0.375 10 false EFI2 NO. 2 3.771,1.063 3.927,1.26 0.156,0.198 10 false 1 5.052,1.063 5.208,1.26 0.156,0.198 10 false 2 3.594,1.531 3.906,1.729 0.313,0.198 10 false d6 3.615,1.698 5.542,2.25 1.927,0.552 10 false Thermostat Heater (Water Inlet with Thermostat Sub-assembly) 5.323,1.177 5.781,1.375 0.458,0.198 10 false C57 5.406,0.969 5.563,1.167 0.156,0.198 10 false 7 5.667,1.188 6.281,1.385 0.615,0.198 10 false HTHM 6.438,3.042 6.75,3.24 0.313,0.198 10 false IC

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WATER INLET WITH THERMOSTAT SUB-ASSEMBLY - ECM)
a.

Disconnect the water inlet with thermostat sub-assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
d6-2 or C57-7 (HTHM) - other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR