Home › Engine / Hybrid System › A25A-FKS (ENGINE CONTROL) › SFI SYSTEM (w/o Canister Pump Module) › from 2017.12
RM33A0E _51 Engine / Hybrid System _065341 A25A-FKS ENGINE CONTROL _0344647 SFI SYSTEM(w/o Canister Pump Module) J

A25A-FKS ENGINE CONTROL  SFI SYSTEM(w/o Canister Pump Module)  Ignition Circuit  


DESCRIPTION

A direct ignition system is used on this vehicle. The direct ignition system is a 1 cylinder ignition system which ignites one cylinder with one ignition coil. In the 1 cylinder ignition system, one spark plug is connected to the end of the secondary winding. High voltage is generated in the secondary winding and is applied directly to the spark plug. The spark of the spark plug passes from the center electrode to the ground electrode.

The ECM determines the ignition timing and transmits the ignition signals for each cylinder. Using the ignition signal, the ECM turns on and off the power transistor inside the igniter, which switches on and off a current to the primary coil. When the current to the primary coil is cut off, high voltage is generated in the secondary coil and this voltage is applied to the spark plugs to create sparks inside the cylinders.

WIRING DIAGRAM

A402877E04
3.385,1.354 5.177,1.75 1.792,0.396 10 false C2 3.344,1.51 5.833,1.885 2.49,0.375 10 false Ignition Coil Assembly (No. 1 Cylinder) 3.344,3.125 6.271,3.406 2.927,0.281 10 false Ignition Coil Assembly (No. 2 Cylinder) 3.344,2.969 5.135,3.365 1.792,0.396 10 false C4 3.323,4.729 5.823,5.219 2.5,0.49 10 false Ignition Coil Assembly (No. 3 Cylinder) 3.365,4.573 5.156,4.969 1.792,0.396 10 false C8 3.281,6.354 5.719,6.635 2.438,0.281 10 false Ignition Coil Assembly (No. 4 Cylinder) 3.313,6.208 5.104,6.604 1.792,0.396 10 false C11 0.375,4.01 1.219,4.365 0.844,0.354 10 false FL MAIN 0.375,2.344 1.219,2.698 0.844,0.354 10 false IG2-MAIN 1.219,1.531 2.063,1.885 0.844,0.354 10 false IG2 NO. 1 5.781,0.573 6.323,0.875 0.542,0.302 10 false IGT1 5.792,2.198 6.333,2.5 0.542,0.302 10 false IGT2 5.792,3.781 6.333,4.083 0.542,0.302 10 false IGT3 5.792,5.292 6.333,5.594 0.542,0.302 10 false IGT4 6.302,6.208 6.844,6.51 0.542,0.302 10 false ECM 5.917,6.208 6.458,6.51 0.542,0.302 10 false C57 2.198,0.833 3.042,1.188 0.844,0.354 10 false INJ 1.021,3.094 2.844,3.573 1.823,0.479 10 false from Certification ECU (Smart Key ECU Assembly)*1 1.01,3.792 2.802,4.323 1.792,0.531 10 false from Ignition Switch Assembly*2 0.667,5.656 2.927,6.135 2.26,0.479 10 false *1: w/ Smart Entry and Start System 0.656,6.115 3.063,6.625 2.406,0.51 10 false *2: w/o Smart Entry and Start System 0.552,4.938 1.396,5.292 0.844,0.354 10 false Battery 1.094,0.573 1.938,0.927 0.844,0.354 10 false 5 1.094,1.073 1.938,1.427 0.844,0.354 10 false 2 1.865,0.573 2.708,0.927 0.844,0.354 10 false 3 1.854,1.083 2.698,1.438 0.844,0.354 10 false 1 3.781,0.563 4.625,0.917 0.844,0.354 10 false 1 3.792,0.885 4.635,1.24 0.844,0.354 10 false 3 4.896,0.583 5.74,0.938 0.844,0.354 10 false 2 3.969,0.688 4.813,1.042 0.844,0.354 10 false +B 3.979,1.01 4.823,1.365 0.844,0.354 10 false GND 4.51,0.698 5.354,1.052 0.844,0.354 10 false IGT1 3.979,2.292 4.823,2.646 0.844,0.354 10 false +B 3.969,3.885 4.813,4.24 0.844,0.354 10 false +B 3.979,5.406 4.823,5.76 0.844,0.354 10 false +B 3.979,2.625 4.823,2.979 0.844,0.354 10 false GND 3.969,4.208 4.813,4.563 0.844,0.354 10 false GND 3.979,5.823 4.823,6.177 0.844,0.354 10 false GND 4.51,2.313 5.354,2.667 0.844,0.354 10 false IGT2 4.5,3.906 5.344,4.26 0.844,0.354 10 false IGT3 4.5,5.427 5.344,5.781 0.844,0.354 10 false IGT4 3.792,2.188 4.635,2.542 0.844,0.354 10 false 1 3.792,3.771 4.635,4.125 0.844,0.354 10 false 1 3.792,5.292 4.635,5.646 0.844,0.354 10 false 1 3.792,2.51 4.635,2.865 0.844,0.354 10 false 3 3.792,4.083 4.635,4.438 0.844,0.354 10 false 3 3.792,5.698 4.635,6.052 0.844,0.354 10 false 3 4.896,2.198 5.74,2.552 0.844,0.354 10 false 2 4.896,3.781 5.74,4.135 0.844,0.354 10 false 2 4.906,5.292 5.75,5.646 0.844,0.354 10 false 2 5.531,0.583 6.375,0.938 0.844,0.354 10 false 49 5.521,2.198 6.365,2.552 0.844,0.354 10 false 48 5.531,3.781 6.375,4.135 0.844,0.354 10 false 47 5.531,5.302 6.375,5.656 0.844,0.354 10 false 46

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:

Perform a spark test before proceeding. If there is no spark for any cylinder, inspect this circuit.

Click hereEngine / Hybrid System>A25A-FKS (ENGINE CONTROL)>IGNITION SYSTEM>ON-VEHICLE INSPECTION


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY)
A402447C01
0.281,0.469 0.688,0.688 0.406,0.219 0.281,0.813 0.688,1.031 0.406,0.219 0.281,1.146 0.688,1.365 0.406,0.219 0.281,1.479 0.688,1.698 0.406,0.219 0.948,1.719 1.365,1.302 false 2.521,1.708 2.104,1.302 false 0.167,0.156 0.479,0.354 0.313,0.198 10 false *a 0.74,1.667 1.052,1.865 0.313,0.198 10 false +B 2.583,1.667 2.896,1.865 0.313,0.198 10 false GND 0.406,0.51 0.719,0.708 0.313,0.198 10 false C2 0.406,0.844 0.719,1.042 0.313,0.198 10 false C4 0.406,1.167 0.719,1.365 0.313,0.198 10 false C8 0.375,1.51 0.688,1.708 0.313,0.198 10 false C11
*a Front view of wire harness connector
(to Ignition Coil Assembly)


a.

Disconnect the ignition coil assembly connectors.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C2-1 (+B) - C2-3 (GND) Ignition switch ON 11 to 14 V
C4-1 (+B) - C4-3 (GND) Ignition switch ON 11 to 14 V
C8-1 (+B) - C8-3 (GND) Ignition switch ON 11 to 14 V
C11-1 (+B) - C11-3 (GND) Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
a.

Disconnect the ignition coil assembly connectors.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-2 (IGT1) - C57-49 (IGT1) Always Below 1 Ω
C4-2 (IGT2) - C57-48 (IGT2) Always Below 1 Ω
C8-2 (IGT3) - C57-47 (IGT3) Always Below 1 Ω
C11-2 (IGT4) - C57-46 (IGT4) Always Below 1 Ω
C2-2 (IGT1) or C57-49 (IGT1) - Body ground and other terminals Always 10 kΩ or higher
C4-2 (IGT2) or C57-48 (IGT2) - Body ground and other terminals Always 10 kΩ or higher
C8-2 (IGT3) or C57-47 (IGT3) - Body ground and other terminals Always 10 kΩ or higher
C11-2 (IGT4) or C57-46 (IGT4) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
a.

Disconnect the ignition coil assembly connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C2-3 (GND) - Body ground Always Below 1 Ω
C4-3 (GND) - Body ground Always Below 1 Ω
C8-3 (GND) - Body ground Always Below 1 Ω
C11-3 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - IGNITION COIL ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (IG2 NO. 1 RELAY - IGNITION COIL ASSEMBLY)
a.

Disconnect the IG2 NO. 1 relay from engine room relay block and junction block assembly.


b.

Disconnect the ignition coil assembly connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (IG2 NO. 1 relay) - C2-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C4-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C8-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) - C11-1 (+B) Always Below 1 Ω
3 (IG2 NO. 1 relay) or C2-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C4-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C8-1 (+B) - Body ground and other terminals Always 10 kΩ or higher
3 (IG2 NO. 1 relay) or C11-1 (+B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR