The cooler control switch assembly is connected via AVC-LAN communication line.
This DTC is stored when an AVC-LAN communication error occurs between the radio and display receiver assembly and cooler control switch assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15DA | Rear Console Recognition Disconnected | When either of the following conditions is met:
·
The cooler control switch assembly is/was not connected while the ignition switch is/was ON or IG ·
Communication between the master unit and the cooler control switch assembly is not possible when the engine is started |
·
Cooler control switch assembly power source circuit ·
AVC-LAN circuit between radio and display receiver assembly and cooler control switch assembly ·
Cooler control switch assembly ·
Stereo component amplifier assembly* ·
Radio and display receiver assembly ·
Harness or connector |
*: for 9 Speakers
The radio and display receiver assembly is the master unit.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:
A communication malfunction DTC may be stored.
The radio and display receiver assembly may not operate normally.
Inspect the fuses for circuits related to this system before performing the following procedure.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 9 Speakers | B |
A
B
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z1 cooler control switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-16 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-9 (+B) - Z1-16 (GND) | Always | 11 to 14 V |
| Z1-10 (IG+) - Z1-16 (GND) | Ignition switch ON | 11 to 14 V |
| Z1-1 (ACC) - Z1-16 (GND) | Ignition switch ACC | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z1 cooler control switch assembly connector.
Disconnect the K3 radio and display receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-7 (TX+) - K3-5 (TX1+) | Always | Below 1 Ω |
| Z1-8 (TX-) - K3-6 (TX1-) | Always | Below 1 Ω |
| Z1-7 (TX+) or K3-5 (TX1+) - Body ground | Always | 10 kΩ or higher |
| Z1-8 (TX-) or K3-6 (TX1-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the cooler control switch assembly with a new or known good one.
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>DISASSEMBLY
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
If DTC B15D3 is output, perform troubleshooting for DTC B15D3 first.
| Result | Proceed to |
|---|---|
| DTC B15D3 is not output. | A |
| DTC B15D3 is output. | B |
A
B
Check that optional components (including associated wiring) which generate radio waves are not installed.
| Result | Proceed to |
|---|---|
| Optional components (including associated wiring) are installed. | A |
| Optional components (including associated wiring) are not installed. | B |
Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.
A
B
Remove optional components (including associated wiring).
Do not remove optional components or associated wiring without the permission of the customer.
| Proceed to |
|---|
| NEXT |
NEXT
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z1 cooler control switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-16 (GND) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-9 (+B) - Z1-16 (GND) | Always | 11 to 14 V |
| Z1-10 (IG+) - Z1-16 (GND) | Ignition switch ON | 11 to 14 V |
| Z1-1 (ACC) - Z1-16 (GND) | Ignition switch ACC | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the Z1 cooler control switch assembly connector.
Disconnect the K10 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Z1-7 (TX+) - K10-20 (TXD+) | Always | Below 1 Ω |
| Z1-8 (TX-) - K10-19 (TXD-) | Always | Below 1 Ω |
| Z1-7 (TX+) or K10-20 (TXD+) - Body ground | Always | 10 kΩ or higher |
| Z1-8 (TX-) or K10-19 (TXD-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the cooler control switch assembly with a new or known good one.
Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY (for Reclining Seat Type)>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the stereo component amplifier assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>STEREO COMPONENT AMPLIFIER>REMOVAL
Clear the DTCs.
Recheck for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG