Home › Engine / Hybrid System › A25A-FKS (FUEL) › FUEL INJECTOR (for Port Injection) › 2017.12–2018.04
RM33A0E _51 Engine / Hybrid System _065343 A25A-FKS FUEL _0319392 FUEL INJECTOR(for Port Injection) A

A25A-FKS FUEL  FUEL INJECTOR(for Port Injection)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during port fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Replacement of port fuel injector assembly

·

Replacement of fuel pressure sensor (fuel delivery pipe with sensor assembly)

·

Replacement of throttle body with motor assembly

·

Cleaning the deposits from the throttle body with motor assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)for A25A-FKS (w/ Canister Pump Module)
(Click here)for A25A-FKS (w/o Canister Pump Module)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 23801P 5.REMOVE NO. 1 FUEL PIPE SUB-ASSEMBLY

Hide 23910A 6.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A401646

Remove the fuel pipe clamp from the fuel tube connector.


b.
A401647

Disconnect the fuel tube sub-assembly from the fuel delivery pipe with sensor assembly.

Click hereEngine / Hybrid System>A25A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23800 7.REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY

a.
A401648

Remove the 2 bolts and fuel delivery pipe with sensor assembly with the 4 port fuel injector assemblies from the cylinder head sub-assembly.

NOTICE:

Be careful not to drop the port fuel injector assemblies when removing the fuel delivery pipe with sensor assembly.



Hide 23807V 8.REMOVE NO. 1 DELIVERY PIPE SPACER

a.
A401649

Remove the 2 No. 1 delivery pipe spacers from the cylinder head sub-assembly.


Hide 23291 9.REMOVE INJECTOR VIBRATION INSULATOR

a.
A401650

Remove the 4 injector vibration insulators from the cylinder head sub-assembly.


Hide 82125N 10.REMOVE NO. 5 ENGINE WIRE

a.
A401651

Disconnect the 4 port fuel injector assembly connectors and fuel pressure sensor connector.


b.

Disengage the 2 clamps to remove the No. 5 engine wire from the fuel delivery pipe with sensor assembly.


Hide 23250F 11.REMOVE PORT FUEL INJECTOR ASSEMBLY

a.
A401652

Pull the 4 port fuel injector assemblies out of the fuel delivery pipe with sensor assembly.


b.
A401653

Remove the O-ring from each port fuel injector assembly.


c.
A401654N01
2,0.417 2.771,0.615 0.771,0.198 10 false No. 1

Attach a tag or label with the corresponding cylinder number to each port fuel injector assembly so that they can be installed to their original locations.

NOTICE:

Cover the port fuel injector assemblies with plastic bags to prevent damage and contamination.