Home › Engine / Hybrid System › A25A-FKS (EMISSION CONTROL) › EGR VALVE › 2017.12–2020.08
RM33A0E _51 Engine / Hybrid System _065344 A25A-FKS EMISSION CONTROL _0328566 EGR VALVE A

A25A-FKS EMISSION CONTROL  EGR VALVE  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during EGR valve assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.DRAIN ENGINE COOLANT

Hide 12601B 2.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY

Hide 3.REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 25680 4.REMOVE EGR COOLER ASSEMBLY

Hide 5.DISCONNECT ENGINE WIRE

a.
A402225C01
0.875,0.042 1.083,0.24 0.208,0.198 10 true *a 2.844,0.323 3.063,0.521 0.219,0.198 10 true *b
*a No. 5 Engine Wire Connector
*b EGR Valve Assembly Connector


Disconnect the No. 5 engine wire connector.


b.

Disconnect the EGR valve assembly connector.


c.

Remove the bolt.


d.

Disengage the 2 wire harness clamps and disconnect the engine wire.


Hide 25601 6.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY

a.
A402228

Using an 8 mm socket wrench, remove the 4 bolts and No. 1 EGR pipe sub-assembly from the intake manifold and EGR valve assembly.


b.
A402226

Remove the EGR valve adapter gasket from the No. 1 EGR pipe sub-assembly.


c.
A402227

Remove the EGR inlet gasket from the intake manifold.


Hide 25620 7.REMOVE EGR VALVE ASSEMBLY

a.
A402229

Slide the clip and disconnect the No. 8 water by-pass hose from the EGR valve assembly.


b.
A402230C01
0.958,2.365 1.375,2.365 false 0.802,2.271 1.052,2.5 0.25,0.229 10 true *a
*a Retainer
V100135

Pinch
V100136

Pull
V100137

Pull off


w/ Water Hose Connector:

i.

Pinch the retainer of the water hose connector and then pull out the retainer to disengage the lock claws and pull off the No. 4 water by-pass hose from the EGR valve assembly.



c.
A430162

w/o Water Hose Connector:

i.

Slide the clip and remove the No. 4 water by-pass hose from the EGR valve assembly.



d.
A402232

Remove the 2 bolts and EGR cooler bracket from the EGR valve bracket and water outlet.


e.
A402233

for EGR Valve Bracket Connection Type:

i.

Using an 8 mm socket wrench, remove the bolt and disconnect the fuel pipe sub-assembly from the EGR valve bracket.



f.
A402234

Using the 8 mm socket wrench, remove the bolt.


g.
A406949C01
2.323,0.813 2.51,0.552 2.51,0.552 2.656,0.552 true 2.333,0.938 2.542,0.938 true 2.583,0.854 2.896,1.052 0.313,0.198 10 true *a 2.708,0.448 3.021,0.646 0.313,0.198 10 true *b
*a Pin
*b Hole


Remove the EGR valve assembly with the EGR valve bracket from the camshaft housing vertically.


h.
A402235

Using the 8 mm socket wrench, remove the bolt and EGR valve assembly from the EGR valve bracket.