Home › Engine / Hybrid System › A25A-FKS (COOLING) › FLOW SHUTTING VALVE (for ATF) › 2017.12–2018.04
RM33A0E _51 Engine / Hybrid System _065346 A25A-FKS COOLING _0319573 FLOW SHUTTING VALVE(for ATF) A

A25A-FKS COOLING  FLOW SHUTTING VALVE(for ATF)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during flow shutting valve (No. 1 water by-pass hose) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: When the ECM is replaced with a new one, reset memory is unnecessary.

Battery terminal is disconnected/reconnected Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control) (Click here)
Pre-collision system
Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of ECM Perform Vehicle Identification Number (VIN) or frame number registration MIL comes on (Click here)(w/ Canister Pump Module)
(Click here)(w/o Canister Pump Module)
Perform code registration (Immobiliser system) Engine start function See Service Bulletin for the registration method.
Replacement of ECM
(If possible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Transfer transaxle compensation code

3.

Perform road test to allow ECM to learn


·

Large shift shock

·

Deterioration of fuel efficiency


(Click here)for UB80E Initialization
(Click here)for UB80E Registration
Replacement of ECM
(If impossible, read the transaxle compensation code from the previous ECM)
1.

Reset memory*1

2.

Reset transaxle compensation code

3.

Perform road test to allow ECM to learn


Replacement of ECM Perform code registration (Immobiliser function)
·

Wireless door lock control system

·

Smart Entry and Start System (for Entry Function)

·

Smart Entry and Start System (for Start Function)

·

Steering lock function


See Service Bulletin for the registration method.

PROCEDURE

Hide 28800 1.REMOVE BATTERY

Hide 74404A 3.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 4.REMOVE FRONT WHEEL LH

Hide 53851M 5.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

Hide 53852K 6.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 8.REMOVE NO. 2 ENGINE UNDER COVER ASSEMBLY

Hide 53737B 9.REMOVE FRONT FENDER APRON SEAL LH

Hide 10.DRAIN ENGINE COOLANT

Hide 16261G 11.REMOVE FLOW SHUTTING VALVE (NO. 1 WATER BY-PASS HOSE)

a.
A402643

Disengage the 3 clamps to remove the transmission breather clamp.


b.
A402644

Disengage the 3 clamps to remove the hose clamp.


c.
A402645

Disengage the 2 clamps to disconnect the flow shutting valve (No. 1 water by-pass hose) and transmission breather hose from the hose clamp.


d.
A403597

Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the water outlet.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and water outlet.



e.
A403596

Slide the clip and disconnect the flow shutting valve (No. 1 water by-pass hose) from the transmission oil cooler.

HINT:

Use a container to catch any engine coolant which flows out of the flow shutting valve (No. 1 water by-pass hose) and transmission oil cooler.



f.
A403577

Disconnect the flow shutting valve connector.


g.
A402650

Remove the bolt and flow shutting valve (No. 1 water by-pass hose).