Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › 2018.04–2021.02
RM33A0E _56 Audio / Visual / Telematics _065373 AUDIO / VIDEO _0323011 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

·

w/o Telematics Transceiver:

The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.

·

w/ Telematics Transceiver:

The radio and display receiver assembly, roof console box sub-assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the telematics transceiver sends power to the roof console box sub-assembly and telephone microphone assembly, and the roof console box sub-assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly via the telematics transceiver.


WIRING DIAGRAM

w/ Sliding Roof
E377468E01
0.521,3.281 1.906,3.833 1.385,0.552 10 false Telephone Microphone Assembly 2.729,3.323 3.865,3.844 1.135,0.521 10 false Roof Console Box Sub-assembly 5.354,3.385 7.031,3.865 1.677,0.479 10 false Radio and Display Receiver Assembly 2.542,2.854 2.917,3.208 0.375,0.354 10 false B 2.531,1.917 2.906,2.271 0.375,0.354 10 false B 2.531,1.448 2.906,1.802 0.375,0.354 10 false B 2.531,0.969 2.906,1.323 0.375,0.354 10 false B 3.677,0.948 4.052,1.302 0.375,0.354 10 false V14 3.667,1.438 4.042,1.792 0.375,0.354 10 false V14 3.667,1.906 4.042,2.26 0.375,0.354 10 false V14 3.656,2.354 4.031,2.708 0.375,0.354 10 false V14 3.677,2.854 4.052,3.208 0.375,0.354 10 false V14 3.75,2.656 4.125,3.01 0.375,0.354 10 false 6 3.719,2.156 4.094,2.51 0.375,0.354 10 false 15 3.74,1.24 4.104,1.594 0.365,0.354 10 false 8 3.75,1.708 4.115,2.063 0.365,0.354 10 false 7 3.75,0.74 4.115,1.094 0.365,0.354 10 false 9 2.542,0.76 2.906,1.115 0.365,0.354 10 false 5 2.542,1.25 2.906,1.604 0.365,0.354 10 false 3 2.552,1.719 2.917,2.073 0.365,0.354 10 false 2 2.552,2.656 2.917,3.01 0.365,0.354 10 false 1 3.188,2.854 3.625,3.177 0.438,0.323 10 false SNS2 3.26,2.344 3.677,2.604 0.417,0.26 10 false GND 3.188,1.896 3.677,2.198 0.49,0.302 10 false MCO- 3.146,1.427 3.635,1.76 0.49,0.333 10 false MCO+ 3.146,0.938 3.635,1.271 0.49,0.333 10 false MACC 5.708,0.969 6.198,1.302 0.49,0.333 10 false MACC 5.698,1.448 6.188,1.781 0.49,0.333 10 false MIN+ 5.708,1.917 6.198,2.25 0.49,0.333 10 false MIN- 5.698,2.385 6.188,2.719 0.49,0.333 10 false SGND 5.708,2.865 6.146,3.188 0.438,0.323 10 false SNS2 5.479,2.75 5.854,3.104 0.375,0.354 10 false 25 5.49,2.281 5.865,2.635 0.375,0.354 10 false 24 5.479,1.802 5.854,2.156 0.375,0.354 10 false 22 5.479,1.323 5.854,1.677 0.375,0.354 10 false 21 5.469,0.844 5.844,1.198 0.375,0.354 10 false 23 5.302,3.177 5.698,3.604 0.396,0.427 10 false K2 4.375,2.208 5.094,2.531 0.719,0.323 10 false (Shielded)

w/o Sliding Roof
E371451E12
0.115,0.115 2.271,0.417 2.156,0.302 12 false w/o Telematics Transceiver: 0.083,4.51 2.125,4.813 2.042,0.302 12 false w/ Telematics Transceiver: 5.677,3.25 6.885,3.688 1.208,0.438 10 false Radio and Display Receiver Assembly 5.677,3.094 6.24,3.375 0.563,0.281 10 false K2 2.875,3.146 4.01,3.594 1.135,0.448 10 false Roof Console Box Sub-assembly 0.656,3.146 2.052,3.594 1.396,0.448 10 false Telephone Microphone Assembly 2.75,2.698 3.177,3.042 0.427,0.344 10 false B 2.74,1.74 3.167,2.083 0.427,0.344 10 false B 2.74,1.271 3.167,1.615 0.427,0.344 10 false B 2.74,0.792 3.167,1.135 0.427,0.344 10 false B 3.875,0.781 4.302,1.125 0.427,0.344 10 false V13 3.885,1.271 4.313,1.615 0.427,0.344 10 false V13 3.875,1.75 4.302,2.094 0.427,0.344 10 false V13 3.323,5.125 3.75,5.469 0.427,0.344 10 false V20 5.917,0.802 6.458,1.073 0.542,0.271 10 false MACC 5.917,1.271 6.458,1.542 0.542,0.271 10 false MIN+ 5.927,1.75 6.469,2.021 0.542,0.271 10 false MIN- 5.917,2.219 6.458,2.49 0.542,0.271 10 false SGND 5.917,2.708 6.458,2.979 0.542,0.271 10 false SNS2 5.698,2.594 6.24,2.865 0.542,0.271 10 false 25 5.708,2.125 6.25,2.396 0.542,0.271 10 false 24 5.698,1.635 6.24,1.906 0.542,0.271 10 false 22 5.698,1.177 6.24,1.448 0.542,0.271 10 false 21 5.698,0.708 6.24,0.979 0.542,0.271 10 false 23 4.573,2.052 5.292,2.375 0.719,0.323 10 false (Shielded) 3.927,1.073 4.469,1.344 0.542,0.271 10 false 10 3.948,0.594 4.49,0.865 0.542,0.271 10 false 9 3.927,1.552 4.469,1.823 0.542,0.271 10 false 11 3.396,4.938 3.938,5.208 0.542,0.271 10 false 3 3.354,0.792 3.896,1.063 0.542,0.271 10 false MACC 3.365,1.26 3.906,1.531 0.542,0.271 10 false MCO+ 3.406,1.729 3.948,2 0.542,0.271 10 false MCO- 3.406,2.698 3.948,2.969 0.542,0.271 10 false SNS2 2.75,2.5 3.021,2.75 0.271,0.25 10 false 1 2.75,1.563 3.021,1.813 0.271,0.25 10 false 2 2.76,1.094 3.031,1.344 0.271,0.25 10 false 3 2.76,0.604 3.031,0.854 0.271,0.25 10 false 5 2.865,5.125 3.406,5.396 0.542,0.271 10 false SNS2 3.865,2.698 4.292,3.042 0.427,0.344 10 false V13 2.833,5.594 3.375,5.865 0.542,0.271 10 false MACC 2.865,6.542 3.406,6.813 0.542,0.271 10 false MCO- 2.833,6.073 3.375,6.344 0.542,0.271 10 false MCO+ 3.333,5.604 3.76,5.948 0.427,0.344 10 false V20 3.323,6.073 3.75,6.417 0.427,0.344 10 false V20 3.323,6.552 3.75,6.896 0.427,0.344 10 false V20 5.708,7.5 6.917,7.938 1.208,0.438 10 false Radio and Display Receiver Assembly 5.719,7.333 6.281,7.615 0.563,0.281 10 false K2 0.688,7.479 2.073,8.021 1.385,0.542 10 false Telephone Microphone Assembly 4.052,7.521 5.531,7.875 1.479,0.354 10 false Telematics Transceiver 4.052,7.354 4.615,7.635 0.563,0.281 10 false K145 4.135,5.51 4.563,5.854 0.427,0.344 10 false 33 4.135,6 4.563,6.344 0.427,0.344 10 false 34 4.135,6.448 4.563,6.792 0.427,0.344 10 false 35 4.135,6.917 4.563,7.26 0.427,0.344 10 false 32 5.917,5.104 6.458,5.375 0.542,0.271 10 false SNS2 5.927,6.063 6.469,6.333 0.542,0.271 10 false MIN+ 5.927,6.552 6.469,6.823 0.542,0.271 10 false MIN- 5.938,7.01 6.479,7.281 0.542,0.271 10 false SGND 5.698,6.906 6.24,7.177 0.542,0.271 10 false 24 5.708,6.448 6.25,6.719 0.542,0.271 10 false 22 5.708,5.969 6.25,6.24 0.542,0.271 10 false 21 5.688,5.021 6.229,5.292 0.542,0.271 10 false 25 5.125,6.427 5.552,6.771 0.427,0.344 10 false 19 5.125,5.958 5.552,6.302 0.427,0.344 10 false 18 4.333,5.615 4.875,5.885 0.542,0.271 10 false MCVD 4.333,6.104 4.875,6.375 0.542,0.271 10 false MCI+ 4.344,6.531 4.885,6.802 0.542,0.271 10 false MCI- 4.344,7.021 4.885,7.292 0.542,0.271 10 false SGND 4.719,6.521 5.26,6.792 0.542,0.271 10 false MCO- 4.688,6.031 5.229,6.302 0.542,0.271 10 false MCO+ 2.385,6.552 2.813,6.896 0.427,0.344 10 false B 2.375,6.073 2.802,6.417 0.427,0.344 10 false B 2.375,5.583 2.802,5.927 0.427,0.344 10 false B 2.385,5.115 2.813,5.458 0.427,0.344 10 false B 2.385,4.938 2.656,5.188 0.271,0.25 10 false 1 2.385,5.396 2.656,5.646 0.271,0.25 10 false 5 2.375,5.896 2.646,6.146 0.271,0.25 10 false 3 2.385,6.365 2.656,6.615 0.271,0.25 10 false 2 3.865,2.198 4.292,2.542 0.427,0.344 10 false V13 3.958,2.01 4.5,2.281 0.542,0.271 10 false 4 3.469,2.198 3.896,2.542 0.427,0.344 10 false GND 3.333,6.99 3.76,7.333 0.427,0.344 10 false V20 2.938,7 3.365,7.344 0.427,0.344 10 false GND 3.385,6.823 3.927,7.094 0.542,0.271 10 false 11 3.417,6.365 3.958,6.635 0.542,0.271 10 false 4 3.417,5.885 3.958,6.156 0.542,0.271 10 false 5 3.406,5.417 3.948,5.688 0.542,0.271 10 false 6 3.927,2.51 4.469,2.781 0.542,0.271 10 false 12 2.438,7.365 3.573,7.813 1.135,0.448 10 false Roof Console Box Sub-assembly 3.865,6.813 4.292,7.156 0.427,0.344 10 false * 5.448,6.813 5.875,7.156 0.427,0.344 10 false * 1.979,8.417 3.094,8.688 1.115,0.271 10 false *: Shielded

CAUTION / NOTICE / HINT

NOTICE:
·

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>PRECAUTION

·

When replacing the radio and display receiver assembly, always replace it with a new one. If a radio and display receiver assembly which was installed to another vehicle is used, the following may occur:

-

A communication malfunction DTC may be stored.

-

The radio and display receiver assembly may not operate normally.




PROCEDURE

1.CHECK MICROPHONE (OPERATION CHECK)
a.
E268457

Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM (for Radio and Display Type)>OPERATION CHECK


b.

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



Result:
Result Proceed to
NG (w/ Sliding Roof) A
NG (w/o Sliding Roof and w/o Telematics Transceiver) B
NG (w/o Sliding Roof and w/ Telematics Transceiver) C
OK D



A

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

B

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

C

14.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)

D

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V14 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V14-6 (SNS2) Always Below 1 Ω
K2-23 (MACC) - V14-9 (MACC) Always Below 1 Ω
K2-21 (MIN+) - V14-8 (MCO+) Always Below 1 Ω
K2-22 (MIN-) - V14-7 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V14-6 (SNS2) - Body ground Always 10 kΩ or higher
K2-23 (MACC) or V14-9 (MACC) - Body ground Always 10 kΩ or higher
K2-21 (MIN+) or V14-8 (MCO+) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V14-7 (MCO-) - Body ground Always 10 kΩ or higher
K2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V14 roof console box sub-assembly connector.


c.
E360498C01
1.531,0.729 1.896,1.01 0.365,0.281 2.813,2.604 2.052,2.156 false 2.271,2.896 1.927,2.156 false 1.198,2.833 1.813,2.146 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN- 2.083,2.896 2.583,3.115 0.5,0.219 10 false MACC 1.01,2.854 1.625,3.052 0.615,0.198 10 false SGND
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-24 (SGND) - Body ground Always Below 1 Ω
K2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E360501C01
1.76,1.24 1.688,0.698 false 1.969,1.24 2.208,0.719 false 0.156,0.146 0.469,0.344 0.313,0.198 10 false *a 1.521,0.531 1.948,0.74 0.427,0.208 10 false MCO- 2.104,0.552 2.531,0.771 0.427,0.219 10 false SNS2
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (SNS2) - 7 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
5.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V14 roof console box sub-assembly connector.


c.

Turn the ignition switch to ACC.


d.
E371629C01
1.563,0.188 2.01,0.427 0.448,0.24 1.167,0.49 1.625,1.333 false 2.219,0.448 1.771,1.333 false 0.167,0.188 0.479,0.385 0.313,0.198 10 false *a 1.656,0.24 1.969,0.438 0.313,0.198 10 false V14 0.802,0.302 1.313,0.51 0.51,0.208 10 false MCO+ 2.281,0.313 2.792,0.521 0.51,0.208 10 false MCO- 2.823,3.438 3.333,3.646 0.51,0.208 10 false GND
*a Component with harness connected
(Roof Console Box Sub-assembly)


Connect an oscilloscope to terminals 8 (MCO+) and 7 (MCO-) of the V14 roof console box sub-assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V14-8 (MCO+) - V14-7 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
6.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C05
1.427,2.792 1.885,3.052 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.677,1.573 1.417,0.865 false 1.833,1.552 2.094,0.854 false 2.448,2.448 2.708,1.75 false 1.031,0.74 1.542,1.01 0.51,0.271 10 false MCO+ 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.708 0.531,2.906 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.573,2.833 2.052,3.052 0.479,0.219 10 false B 2.167,0.75 2.708,0.969 0.542,0.219 10 false MCO- 2.135,2.396 2.677,2.615 0.542,0.219 10 false GND
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-8 (MCO+) - B-3 Always Below 1 Ω
V14-7 (MCO-) - B-2 Always Below 1 Ω
V14-8 (MCO+) or B-3 - V14-15 (GND) Always 10 kΩ or higher
V14-7 (MCO-) or B-2 - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

7.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371472C06
1.427,2.938 1.885,3.198 0.458,0.26 1.563,0.427 2.021,0.688 0.458,0.26 1.969,1.583 2.229,0.885 false 2.5,2.281 2.708,1.75 false 1.813,1.583 1.375,0.917 false 0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 0.219,2.896 0.531,3.094 0.313,0.198 10 false *b 1.646,0.479 2.125,0.698 0.479,0.219 10 false V14 1.583,2.979 2.063,3.198 0.479,0.219 10 false B 2.302,0.781 2.844,1 0.542,0.219 10 false SNS2 2.188,2.281 2.729,2.5 0.542,0.219 10 false GND 0.979,0.802 1.521,1.021 0.542,0.219 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V14-6 (SNS2) - B-1 Always Below 1 Ω
V14-7 (MCO-) - B-2 Always Below 1 Ω
V14-6 (SNS2) or B-1 - V14-15 (GND) Always 10 kΩ or higher
V14-7 (MCO-) or B-2 - V14-15 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V13 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V13-12 (SNS2) Always Below 1 Ω
K2-23 (MACC) - V13-9 (MACC) Always Below 1 Ω
K2-21 (MIN+) - V13-10 (MCO+) Always Below 1 Ω
K2-22 (MIN-) - V13-11 (MCO-) Always Below 1 Ω
K2-25 (SNS2) or V13-12 (SNS2) - Body ground Always 10 kΩ or higher
K2-23 (MACC) or V13-9 (MACC) - Body ground Always 10 kΩ or higher
K2-21 (MIN+) or V13-10 (MCO+) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or V13-11 (MCO-) - Body ground Always 10 kΩ or higher
K2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V13 roof console box sub-assembly connector.


c.
E360498C03
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 false 2.188,2.885 1.927,2.146 false 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.094,2.896 2.729,3.115 0.635,0.219 10 false MACC 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K2-23 (MACC) - Body ground Ignition switch ACC 4 to 6 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-24 (SGND) - Body ground Always Below 1 Ω
K2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

10.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.
E360499C01
1.74,1.698 1.573,1.385 false 1.219,1.719 1.458,1.385 false 0.25,0.156 0.563,0.354 0.313,0.198 10 false *a 1.031,1.719 1.479,1.958 0.448,0.24 10 false SNS2 1.667,1.698 2.156,1.958 0.49,0.26 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
12 (SNS2) - 11 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

11.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
11.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V13 roof console box sub-assembly connector.


c.

Turn the ignition switch to ACC.


d.
E371634C03
1.448,0.177 1.906,0.458 0.458,0.281 2.063,2.135 1.792,1.448 false 1.198,2.146 1.542,1.427 false 0.156,0.167 0.552,0.375 0.396,0.208 10 false *a 1.542,0.24 1.938,0.448 0.396,0.208 10 false V13 0.823,2.104 1.323,2.302 0.5,0.198 10 false MCO- 2.115,2.083 2.615,2.281 0.5,0.198 10 false MCO+ 2.813,3.448 3.313,3.646 0.5,0.198 10 false GND
*a Component with harness connected
(Roof Console Box Sub-assembly)


Connect an oscilloscope to terminals 10 (MCO+) and 11 (MCO-) of the V13 roof console box sub-assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V13-10 (MCO+) - V13-11 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
12.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C11
1.5,2.75 1.917,3 0.417,0.25 1.417,0.583 1.833,0.833 0.417,0.25 1.042,1.531 0.771,0.969 false 1.51,2.083 1.625,1.74 false 2.156,2.208 1.917,1.771 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.198,2.073 1.708,2.354 0.51,0.281 10 false MCO- 2.208,2.177 2.719,2.458 0.51,0.281 10 false MCO+ 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V13 1.656,2.792 2.167,3.073 0.51,0.281 10 false B
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-10 (MCO+) - B-3 Always Below 1 Ω
V13-11 (MCO-) - B-2 Always Below 1 Ω
V13-10 (MCO+) or B-3 - V13-4 (GND) Always 10 kΩ or higher
V13-11 (MCO-) or B-2 - V13-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

13.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E371473C12
1.458,2.75 1.885,3.01 0.427,0.26 1.417,0.563 1.844,0.823 0.427,0.26 1.042,1.531 0.771,0.969 false 1.417,2.073 1.531,1.729 false 1.854,2.125 1.646,1.75 false 0.26,0.292 0.573,0.49 0.313,0.198 10 false *a 0.281,2.74 0.594,2.938 0.313,0.198 10 false *b 1.052,2.083 1.563,2.365 0.51,0.281 10 false SNS2 0.448,0.875 0.958,1.156 0.51,0.281 10 false GND 1.5,0.625 2.01,0.906 0.51,0.281 10 false V13 1.604,2.792 2.115,3.073 0.51,0.281 10 false B 1.896,2.094 2.406,2.375 0.51,0.281 10 false MCO-
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V13-12 (SNS2) - B-1 Always Below 1 Ω
V13-11 (MCO-) - B-2 Always Below 1 Ω
V13-12 (SNS2) or B-1 - V13-4 (GND) Always 10 kΩ or higher
V13-11 (MCO-) or B-2 - V13-4 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

14.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the V20 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-25 (SNS2) - V20-3 (SNS2) Always Below 1 Ω
K2-25 (SNS2) or V20-3 (SNS2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEMATICS TRANSCEIVER)
a.

Disconnect the K2 radio and display receiver assembly connector.


b.

Disconnect the K145 telematics transceiver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-21 (MIN+) - K145-18 (MCO+) Always Below 1 Ω
K2-22 (MIN-) - K145-19 (MCO-) Always Below 1 Ω
K2-21 (MIN+) or K145-18 (MCO+) - Body ground Always 10 kΩ or higher
K2-22 (MIN-) or K145-19 (MCO-) - Body ground Always 10 kΩ or higher
K2-24 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (TELEMATICS TRANSCEIVER - ROOF CONSOLE BOX SUB-ASSEMBLY)
a.

Disconnect the K145 telematics transceiver connector.


b.

Disconnect the V20 roof console box sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K145-33 (MCVD) - V20-6 (MACC) Always Below 1 Ω
K145-34 (MCI+) - V20-5 (MCO+) Always Below 1 Ω
K145-35 (MCI-) - V20-4 (MCO-) Always Below 1 Ω
K145-33 (MCVD) or V20-6 (MACC) - Body ground Always 10 kΩ or higher
K145-34 (MCI+) or V20-5 (MCO+) - Body ground Always 10 kΩ or higher
K145-35 (MCI-) or V20-4 (MCO-) - Body ground Always 10 kΩ or higher
K145-32 (SGND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Disconnect the K145 telematics transceiver connector.


b.
E360498C02
1.531,0.729 1.896,1.01 0.365,0.281 1.292,2.792 1.802,2.156 false 2.813,2.604 2.052,2.156 false 0.25,0.24 0.563,0.438 0.313,0.198 10 false *a 1.635,0.792 1.948,0.99 0.313,0.198 10 false K2 1.042,2.813 1.49,3.052 0.448,0.24 10 false SGND 2.865,2.563 3.24,2.771 0.375,0.208 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Connect the K2 radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K2-24 (SGND) - Body ground Always Below 1 Ω
K2-22 (MIN-) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

18.INSPECT TELEMATICS TRANSCEIVER

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

18.INSPECT TELEMATICS TRANSCEIVER
a.

Connect the K145 telematics transceiver connector.


b.
E259127C82
1.469,0.531 1.906,0.802 0.438,0.271 0.583,2.75 1.188,2.125 false 1.083,2.75 1.385,2.125 false 2.083,2.75 1.49,2.125 false 0.167,0.167 0.417,0.333 0.25,0.167 10 false *a 1.521,0.583 1.917,0.781 0.396,0.198 10 false K145 0.333,2.781 0.75,2.948 0.417,0.167 10 false MCI- 0.833,2.781 1.333,2.948 0.5,0.167 10 false MCVD 2,2.781 2.5,2.948 0.5,0.167 10 false SGND
*a Component with harness connected
(Telematics Transceiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
K145-33 (MCVD) - Body ground Ignition switch ACC 4 to 6 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K145-35 (MCI-) - Body ground Always Below 1 Ω
K145-32 (SGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

19.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY

NG

19.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Connect the B telephone microphone assembly connector.


c.
E360500C02
1.927,1.229 1.479,0.698 false 2.104,1.219 2.583,0.719 false 0.125,0.135 0.438,0.333 0.313,0.198 10 false *a 1.302,0.521 1.813,0.729 0.51,0.208 10 false MCO- 2.438,0.542 2.969,0.802 0.531,0.26 10 false SNS2
*a Component without harness connected
(Roof Console Box Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 (SNS2) - 4 (MCO-) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

20.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

23.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
20.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V20 roof console box sub-assembly connector.


c.

Turn the ignition switch to ACC.


d.
E369494C10
1.542,0.344 1.917,0.594 0.375,0.25 1.771,1.479 1.208,0.583 false 1.917,1.469 2.354,0.604 false 1,0.396 1.615,0.594 0.615,0.198 10 false MCO+ 2.24,0.417 2.854,0.615 0.615,0.198 10 false MCO- 1.615,0.396 2.229,0.594 0.615,0.198 10 false V20 2.813,3.438 3.427,3.635 0.615,0.198 10 false GND 0.135,0.094 0.75,0.292 0.615,0.198 10 false *a
*a Component with harness connected
(Roof Console Box Sub-assembly)


Connect an oscilloscope to terminals 5 (MCO+) and 4 (MCO-) of the V20 roof console box sub-assembly connector.


e.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal V20-5 (MCO+) - V20-4 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

21.INSPECT TELEMATICS TRANSCEIVER (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

22.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
21.INSPECT TELEMATICS TRANSCEIVER (OUTPUT TO RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Connect the K2 radio and display receiver assembly connector.


b.

Connect the V20 roof console box sub-assembly connector.


c.

Connect the K145 telematics transceiver connector.


d.

Turn the ignition switch to ACC.


e.
E364296C26
1.5,0.229 1.906,0.49 0.406,0.26 1.24,1.385 1.104,0.563 false 1.083,2.125 1.323,1.385 false 0.229,0.188 0.542,0.385 0.313,0.198 10 false *a 1.542,0.281 2,0.479 0.458,0.198 10 false K145 0.677,2.073 1.292,2.271 0.615,0.198 10 false MCO+ 0.719,0.406 1.333,0.604 0.615,0.198 10 false MCO- 2.823,3.458 3.24,3.656 0.417,0.198 10 false GND
*a Component with harness connected
(Telematics Transceiver)


Connect an oscilloscope to terminals 18 (MCO+) and 19 (MCO-) of the K145 telematics transceiver connector.


f.

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Measurement terminal K145-18 (MCO+) - K145-19 (MCO-)
Tool setting 50 mV/DIV., 500 ms/DIV.
Vehicle condition
1.

Turn the ignition switch to ACC.

2.

Sound is input to the roof console box sub-assembly when the user is closer than 125 mm from the roof console box sub-assembly sound holes.



OK:

The waveform is similar to that shown in the illustration.


HINT:

The oscilloscope waveform shown in the illustration is an example for reference only.



Result:
Proceed to
OK
NG



OK

NG

22.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E369493C32
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 2.542,2.156 2.333,1.708 false 1.75,1.438 1.25,0.927 false 1.906,1.438 2.333,0.927 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 1.021,0.75 1.521,0.969 0.5,0.219 10 false MCO+ 2.188,0.76 2.667,0.969 0.479,0.208 10 false MCO- 2.438,2.188 2.927,2.417 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.531,0.448 2.01,0.656 0.479,0.208 10 false V20
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V20-5 (MCO+) - B-3 Always Below 1 Ω
V20-4 (MCO-) - B-2 Always Below 1 Ω
V20-5 (MCO+) or B-3 - V20-11 (GND) Always 10 kΩ or higher
V20-4 (MCO-) or B-2 - V20-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY

23.INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY
a.

Remove the roof console box sub-assembly.

Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL


b.

Disconnect the B telephone microphone assembly connector.


c.
E369493C33
1.458,0.396 1.844,0.646 0.385,0.25 1.479,2.813 1.875,3.063 0.396,0.25 2.542,2.156 2.333,1.708 false 1.896,1.438 1.396,0.927 false 2.052,1.438 2.479,0.927 false 0.521,0.385 0.833,0.583 0.313,0.198 10 false *a 0.521,2.719 0.833,2.917 0.313,0.198 10 false *b 2.354,0.75 2.854,0.969 0.5,0.219 10 false SNS2 1.198,0.75 1.677,0.958 0.479,0.208 10 false MCO- 2.438,2.188 2.927,2.417 0.49,0.229 10 false GND 1.635,2.854 1.948,3.052 0.313,0.198 10 false B 1.531,0.448 2.01,0.656 0.479,0.208 10 false V20
*a Component without harness connected
(Roof Console Box Sub-assembly (No. 1 Roof Wire Side))
*b Component without harness connected
(Roof Console Box Sub-assembly (Telephone Microphone Assembly Side))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
V20-3 (SNS2) - B-1 Always Below 1 Ω
V20-4 (MCO-) - B-2 Always Below 1 Ω
V20-3 (SNS2) or B-1 - V20-11 (GND) Always 10 kΩ or higher
V20-4 (MCO-) or B-2 - V20-11 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE ROOF CONSOLE BOX SUB-ASSEMBLY